Atomistic simulations of grain boundary migration in copper

While the motion of twist boundaries can be readily studied by atomistic simulations with molecular dynamics (MD) under the action of an elastic driving force, the approach fails for tilt boundaries. This is due to the interaction of the elastic stress with the grain boundary (GB) structure, which causes plastic strain by GB sliding. A novel concept, the orientation correlated driving force, is introduced to circumvent this problem. It is shown that this concept can be successfully applied to the study of the migration of tilt boundaries. The migration behavior of several twist and tilt GBs was investigated. The transition from low-to high-angle boundaries can be captured, and a structural transition of tilt boundaries was found at high temperatures, which also affected the migration behavior. The results compare well with experimental results of the motion high-angle boundaries, but for low-angle boundaries, the agreement is poor. This article is based on a presentation made in the “Hillert Symposium on Thermodynamics & Kinetics of Migrating Interfaces in Steels and Other Complex Alloys,” December 2–3, 2004, organized by The Royal Institute of Technology in Stockholm, Sweden.     

Synthesis and characterization of biocompatible hydroxyapatite coated ferrite

Ferrite particles coated with biocompatible phases can be used for hyperthermia treatment of cancer. We have synthesized substituted calcium hexaferrite, which is not stable on its own but is stabilized with small substitution of La. Hexaferrite of chemical composition (CaO)_0.75(La₂0₃)_0.20(Fe₂O₃)₆ was prepared using citrate gel method. Hydroxyapatite was prepared by precipitating it from aqueous solution of Ca(NO₃)₂ and (NH₄)₂HPO₄ maintaining pH above 11. Four different methods were used for coating of hydroxyapatite on ferrite particles. SEM with EDX and X-ray diffraction analysis shows clear evidence of coating of hydroxyapatite on ferrite particles. These coated ferrite particles exhibited coercive field up to 2 kOe, which could be made useful for hysteresis heating in hyperthermia. Studies by culturing BHK-21 cells and WBC over the samples show evidence of biocompatibility. SEM micrographs and cell counts give clear indication of cell growth on the surface of the sample. Finally coated ferrite particle was implanted in Kasaulli mouse to test its biocompatibility. The magnetic properties and biocompatibility studies show that these hydroxyapatite coated ferrites could be useful for hyperthermia.     

Untersuchung der Verteilung und Intensität filamentierter Barrierenplasmen für die Behandlung von Oberflächen

The application of barrier discharges at atmospheric pressure in air expands on the market of plasma technology, because it is an ecological and cost‐effective alternative to other processes of surface treatment. These plasmas usually consist of a multitude of spatially and temporally localized filaments, whose distribution should be as even as possible for homogeneous treatment. This holds especially for the plasma treatment of sensitive goods such as wool or other textiles. In equipment for continuous pass of material the barrier arrangements often consist of a system cylinder – cylinder or cylinder – plane, whereby the gap width changes locally. Space distribution and intensity of filaments has been investigated by means of short‐time photography and spatially resolved measurement of current distribution and energy distribution derived from it. The local dependency found can be explained by means of a capacitive equivalent circuit.     

Electrochemical synthesis and characterization of chloride doped polyaniline

Chloride doped polyaniline conducting polymer films have been prepared in a protic acid medium (HCl) by potentiodynamic method in an electrochemical cell and studied by cyclic voltammetry and FTIR techniques. The FTIR spectra confirmed Cl^- ion doping in the polymers. The polymerization rate was found to increase with increasing concentration of aniline monomer. But the films obtained at high monomer concentration were rough having a nonuniform flaky polyaniline distribution. Results showed that the polymerization rate did not increase beyond a critical HCl concentration. Cyclic voltammetry suggested that, the oxidation-reduction current increased with an increase in scan rate and that the undoped polyaniline films were not hygroscopic whereas chloride doped polyaniline films were found to be highly hygroscopic.     

Strengthening of concrete prisms using the plate-bonding technique

This paper presents the use of fracture mechanics for the plate bonding technique. Plates of steel or carbon-fibre reinforced plastic are bonded with an epoxy adhesive to rectangular concrete prisms and loaded in shear up to failure, what is normally known in fracture mechanics as mode II failure. In this special application a linear and a nonlinear approach are presented. The nonlinear equation derived for a realistic shear-deformation curve can only be used for numerical calculations. However, for simplified shear-deformation curves, the derived formula can be solved analytically. Results from tests, which are compared with the theory, are also presented.     

Electromigration-induced damage in bamboo Al interconnects

Depletion and hillock formation were examined in-situ in a scanning electron microscope (SEM) during electromigration of bamboo Al interconnect segments. Hillocks formed directly at the anode ends of the segments by epitaxial addition of Al at the bottom Al/TiN interface. Depletion occurred nonuniformly from the cathode end and stopped once the distance between the leading void and the hillock reached the critical length for electromigration at the given current density. A modified equation for the drift velocity is proposed, which includes the effect of nonuniform depletion and predicts that interconnects with nonuniform depletion are more reliable than those with uniform depletion.     

Evaluating the impact of CASE: an empirical comparison of retrospective and cross-sectional survey approaches

The purpose of this paper is to evaluate two methods of assessing the productivity and quality impact of Computer Aided Software Engineering (CASE) and Fourth Generation Language (4GL) technologies: (1) by the retrospective method; and (2) the cross-sectional method. Both methods involve the use of questionnaire surveys. Developers' perceptions depend on the context in which they are expressed and this includes expectations about the effectiveness of a given software product. Consequently, it is generally not reliable to base inferences about the relative merits of CASE and 4GLs on a cross-sectional comparison of two separate samples of users. The retrospective method that requires each respondent to directly compare different products is shown to be more reliable. However, there may be scope to employ cross-sectional comparisons of the findings from different samples where both sets of respondents use the same reference point for their judgements, and where numerical rather than verbal rating scales are used to measure perceptions.