Characteristics of tiger nut milk: effects of milling

A standard method for the extraction of tiger nut milk has been introduced. It has been shown that, although milling duration improves the yield of tiger nut milk solids and its nutrient composition, there is a quantifiable loss of nutrient in the pressing residue during milk extraction. Milling duration improved the colloidal stability of the milk against creaming during 16 h of storage. A higher milling intensity resulted in the aggregation of biological polymers which resulted in colloidal destabilisation. Milling improved the lightness and stability and reduced browning rate of the tiger nut milk during storage. This report is important for the production of tiger nut milk of consistent and comparable characteristics. Milling has been introduced as a processing method for the qualitative and quantitative modulation of the properties of tiger nut milk. It is recommended to develop further strategies to improve the colloidal stability of tiger nut milk as a beverage.     

Combination of nuclear magnetic resonance spectroscopy and nonlinear methods to analyze the copolymerization of phosphonic acid derivatives

We demonstrate in this study that the combination of modern inline monitoring methods [here: inline nuclear magnetic resonance (NMR)] with simulations gains more exact and profound kinetic results than previously used methods like linearization without that combination. The ¹H-NMR spectroscopic data (more than 100 data points) are used to construct the copolymerization diagram. The reactivity ratios are obtained applying the van Herks nonlinear least square method. The examination of the radical copolymerization of 2-hydroxyethyl methacrylate (HEMA) with (2-{[2-(ethoxycarbonyl)prop-2-en-1-yl]oxy}ethyl) phosphonic acid (ECPPA) as important adhesive monomer used in dentistry yields reactivity ratios of r_HEMA = 1.83; r_ECPPA = 0.42. The copolymerization diagram reflects nonideal, non-azeotropic copolymerization. The sequence distribution of the obtained by Monte Carlo simulation indicates the generation of statistical copolymers. As an important finding, it is demonstrated that the repeating units responsible for etching and adhesion are arranged over the whole polymer chain, which is necessary to achieve proper functionality. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 48256.     

ENHANCING THE CREATIVITY OF REENGINEERING Techniques for Making IS More Creative

Industries in the US continue to lose ground in international competition. If IS is to help change that trend, it will have to become more creative. Creativity improvement programs are being introduced in other areas of the company— now is the time for IS organizations to follow suit.     

Development and characterization of a biocompatible OH-modified copolymer based on polyurethane

Different polyurethanes were synthesized by varying the diol as well as the diisocyanate components and chain extenders. Polyurethanes with OH-groups were obtained by photo- and thermoinitiation of the radical polymerization of hydroxy alkyl acrylates in the presence of the polyurethanes. The polymers were evaluated with respect to their biocompatibility by measuring the cell spreading, the rates of DNA- and protein synthesis and the swelling behaviour. The differences in the surfaces and the bulks between the selected basic polyurethane and the functionalized modification were determined and characterized by XPS, FTIR-ATR and ¹³C-FT-NMR-spectroscopy. The mechanical data of Tecoflex EG 60D® and Pellethane 2363–80AE® were compared with the data of the synthesized polyurethanes.     

Lifetime assessment of epoxies by the kinetics of thermal degradation

The kinetics of thermal degradation of 4,4′‐diaminodiphenylsulfone (DDS)‐cured glycidylethers (DGBA) and glycidylamines (TGDDM) have been studied by isothermal annealing. Thermal degradation proceeds via first‐order kinetics with activation energies of 138 (DGBA/DDS) and 95 kJ/mol (TGDDM/DDS). From these data the temperature‐dependent lifetime can be calculated. Based on the heat distortion temperature and 20 years' service as criteria, the upper service temperature is found to be around 115–120°C. In spite of the different activation energies and bond stabilities, only marginal differences in the upper allowed service temperatures between these resins were found. Only slight improvements can be expected by optimizing the cure conditions. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1881–1886, 2004     

Effects of microreactor wall heat conduction on the reforming process of methane

In this paper, the effect of wall conduction of an autothermal tubular methane microreformer is investigated numerically. It is found that the axial wall conduction can strongly influence the performance of the microreactor and should not be neglected without a careful a priori investigation of its impact. By increasing the wall thermal conductivity, the maximum wall surface temperature is decreased. Due to the complex exothermic–endothermic nature of the chemistry of reforming, the axial variation of the wall temperature is not monotonic. Methane conversion and hydrogen yield are strongly dependent on the wall inner surface temperature, hence the heat conduction through the channel wall. The equivalence ratio and the wall thickness also significantly affect the reforming effectiveness and must be carefully considered in reactor optimization. Furthermore, it is found that exothermic oxidation reaction mechanisms, especially partial oxidation, are responsible for syngas (hydrogen and carbon monoxide) production near the inlet. Farther downstream, in the oxygen deficient region, endothermic steam reforming is the main hydrogen producing mechanism. By increasing the thermal conductivity, steam reforming becomes stronger and partial oxidation becomes weaker. For all investigated inlet conditions, the highest hydrogen yield is obtained for no or very low conductive walls.     

Investigating teamwork and taskwork in single- and multi-display groupware systems

Multi-display groupware (MDG) systems, which typically comprise both public and personal displays, promise to enhance collaboration, yet little is understood about how they differ in use from single-display groupware (SDG) systems. While research has established the technical feasibility of MDG systems, evaluations have not addressed the question of how users’ behave in such environments, how their interface design can impact group behavior, or what advantages they offer for collaboration. This paper presents a user study that investigates the impact of display configuration and software interface design on taskwork and teamwork. Groups of three completed a collaborative optimization task in single- and multi-display environments, under different task interface constraints. Our results suggest that MDG configurations offer advantages for performing individual task duties, whereas SDG conditions offer advantages for coordinating access to shared resources. The results also reveal the importance of ergonomic design considerations when designing co-located groupware systems.     

Sub‐Micron Anisotropic InP‐based III–V Semiconductor Material Deep Etching for On‐Chip Laser Photonics Devices

Two InP‐based III–V semiconductor etching recipes are presented for fabrication of on‐chip laser photonic devices. Using inductively coupled plasma system with a methane free gas chemistry of chlorine and nitrogen at a high substrate temperature of 250 °C, high aspect ratio, anisotropic InP‐based nano‐structures are etched. Scanning electron microscopy images show vertical sidewall profile of 90° ± 3°, with aspect ratio as high as 10. Atomic Force microscopy measures a smooth sidewall roughness root‐mean‐square of 2.60 nm over a 3 × 3 μm scan area. The smallest feature size etched in this work is a nano‐ring with inner diameter of 240 nm. The etching recipe and critical factors such as chamber pressure and the carrier plate effect are discussed. The second recipe is of low temperature (?10 °C) using Cl₂ and BCl₃ chemistry. This recipe is useful for etching large areas of III–V to reveal the underlying substrate. The availability of these two recipes has created a flexible III–V etching platform for fabrication of on‐chip laser photonic devices. As an application example, anisotropic InP‐based waveguides of 3 μm width are fabricated using the Cl₂ and N₂ etch recipe and waveguide loss of 4.5 dB mm^?1 is obtained.