Analysis of stepwise charging limits and its implementation for efficiency improvement in switched capacitor DC–DC converters

In this work we analysed the stepwise charging technique to find the limits from which it is beneficial in terms of load capacitance and charge–discharge frequency. We included in the analysis practical limitations such as the consumption of auxiliary logic needed to implement the technique and the minimum size of auxiliary switches imposed by the technology. We proposed an ultra-low-power logic block to push these limits and to obtain benefits from this technique in small capacitances. Finally, we proposed to use a stepwise driver in the driving of the gate capacitance of power switches in switched-capacitor (SC) DC–DC converters. We designed and manufactured, in a 130 nm process, a SC DC–DC converter and measured a 29% energy reduction in the gate-drive losses of the converter. This accounts for an improvement of 4% (from 69 to 73%) in the overall converter efficiency.

     

Evaluation of direct light processing for the fabrication of bioactive ceramic scaffolds: Effect of pore/strut size on manufacturability and mechanical performance

Bioactive ceramic scaffolds for bone regeneration consisting of a three-dimensional mesh of interpenetrating struts with square section were fabricated via Digital Light Processing (DLP). The ability of the technique to manufacture 3D porous structures from β-tricalcium phosphate (β-TCP) powders with different dimensions of struts and pores was evaluated, identifying the possibilities and limitations of the manufacturing process. Small pore sizes were found to seriously complicate the elimination of excess slurry from the scaffold’s innermost pores. The effect of the strut/pore size on the mechanical performance of the scaffolds under compressive stresses was also evaluated, but no significant influence was found. Under compressive stresses, the structures resulted weaker when tested perpendicularly to the printing plane due to interlayer shear failure. Interlayer superficial grooves are proposed as potential failure-controlling defects, which could also explain the lack of a Weibull size effect on the mechanical strength of the fabricated DLP scaffolds.     

Design of a Web Based Underwater Acoustic Communication Testbed and Simulation Platform

Wireless Personal Communications - Underwater Wireless Sensor Networks (UWSNs) are playing a vital role in exploring the unseen underwater (UW) natural resources. However, performance evaluation of...     

Two-step sinter-crystallization of K2O–CaO–P2O5–SiO2 (45S5-K) bioactive glass

Bioactive glasses and glass-ceramics (GCs) effectively regenerate bone tissue, however most GCs show improved mechanical properties. In this work, we developed and tested a rarely studied bioactive glass composition (24.4K₂O-26.9CaO-46.1SiO₂-2.6P₂O₅ mol%, identified as 45S5-K) with different particle sizes and heating rates to obtain a sintered GC that combines good fracture strength, low elastic modulus, and bioactivity. We analyzed the influence of the sintering processing conditions in the elastic modulus, Vickers microhardness, density, and crystal phase formation in the GC. The best GC shows improved properties compared with its parent glass. This glass achieves a good densification degree with a two-step viscous flow sintering approach and the resulting GC shows as high bioactivity as that of the standard 45S5 Bioglass®. Furthermore, the GC elastic modulus (56 GPa) is relatively low, minimizing stress shielding. Therefore, we unveiled the glass sintering behavior with concurrent crystallization of this complex bioactive glass composition and developed a potential GC for bone regeneration.     

Fat Distribution and Lipid Profile of Young Adults with Congenital Adrenal Hyperplasia Due to 21-Hydroxylase Enzyme Deficiency

We aimed to compare detailed fat distribution and lipid profile between young adults with congenital adrenal hyperplasia due to 21-hydroxylase enzyme deficiency and a control group. We also verified independent associations of treatment duration and daily hydrocortisone dose equivalent (HDE) with lipid profile within patients. This case–control study included 23 patients (7 male and 16 female) matched by an age range of young adults (18–31 years) with 20 control subjects (8 male and 12 female). Dual energy X-ray absorptiometry was used to measure the fat distribution. Male patients demonstrated elevated indices of fat mass for total (7.7 ± 2.1 vs. 4.5 ± 1.3 kg/m², p = 0.003), trunk (4.0 ± 1.2 vs. 2.2 ± 0.8 kg/m², p = 0.005), android (0.63 ± 0.24 vs. 0.32 ± 0.15 kg/m², p = 0.008), gynoid (1.34 ± 0.43 vs. 0.74 ± 0.24 kg/m², p = 0.005), arm (0.65 ± 0.16 vs. 0.39 ± 0.10 kg/m², p = 0.009), and leg regions (2.7 ± 0.8 vs. 1.6 ± 0.4 kg/m², p = 0.005) than the control group, but not in females. However, female patients demonstrated elevated ratio of low-density lipoprotein cholesterol to high-density lipoprotein cholesterol (1.90 ± 0.46 vs. 1.39 ± 0.47, p = 0.009) than the control group, but not in males. Total fat mass was inversely correlated with total testosterone (r = −0.64, p = 0.014) and positively correlated with leptin in males (r = 0.75, p = 0.002). An elevated daily HDE (β = 0.43, p = 0.038 and β = 0.47, p = 0.033) and trunk to total fat mass ratio (β = 0.46, p = 0.025, and β = 0.45, p = 0.037) were independently correlated with impaired lipid profile markers. Although there is no altered lipid profile, male patients demonstrated an increased fat distribution. However, female patients presented with an impaired lipid profile marker but demonstrated close values of normal fat distribution. Interestingly, the dose of glucocorticoid therapy can have some role in the lipid mechanisms.     

Physicochemical and technological properties of beef burger as influenced by the addition of pea fibre

This study aimed to evaluate the physicochemical characteristics and sensory attributes of beef burgers with the addition of pea fibre as a partial substitute of meat or fat. Three formulations were prepared: control (CON) – similar to the commercial formulation; fibre/less meat (FLM)—5% meat reduction and addition of 1% pea fibre; fibre/less fat (FLF)—7% fat reduction and addition of 1% pea fibre. Non-significant differences were obtained for pH, colour parameters (L* and b*), texture profile, cooking loss and size reduction among formulations. Moreover, sensory analysis with consumers of beef burgers did not indicate differences among the formulations for all the analysed attributes. Therefore, pea fibre is a promising partial replacer for meat and fat in beef burgers due to the preservation of technological parameters and sensory acceptance.     

Optimization of quinacridone magenta,Cu-phthalocyanine cyan,and arylide yellow ink films formulated for maximum color gamut

Investigation of ink formulation options with the purpose to obtain color-gamut-optimal set of Cyan Magenta and Yellow CMY inks is reported. Implementation of the thickness dependent Kubelka-Munk model on multiple ink layers having different and well-defined thicknesses, provides characteristic absorption and scattering (K, S ) spectra of the ink ingredients. These data enable accurate computation of the reflectance spectrum and thus the L*a*b* color coordinates for any given ink thickness or substrate. Pigment materials investigated are quinacridone as magenta, copper-phthalocyanine as cyan, and arylide yellow. Scaling the peak of the absorption band to the number of molecules per unit area for the specific pigments studied in this article provides the molar extinction coefficients, 1.21 × 10⁴ , 4.7 × 10⁴ , and 3.3 × 10⁴ cm²/millimole respectively, regardless of the different ink formulations used, in accord with Avogadro's principle. Having a set of three pairs of K, S spectra is used to compute the color gamut of any CMY color combination in the L*a*b* space as a function of ink layer thickness and formulation. Using an iterative algorithm, a color-gamut-optimal set of CMY inks is obtained.