Evaluation of direct light processing for the fabrication of bioactive ceramic scaffolds: Effect of pore/strut size on manufacturability and mechanical performance

Bioactive ceramic scaffolds for bone regeneration consisting of a three-dimensional mesh of interpenetrating struts with square section were fabricated via Digital Light Processing (DLP). The ability of the technique to manufacture 3D porous structures from β-tricalcium phosphate (β-TCP) powders with different dimensions of struts and pores was evaluated, identifying the possibilities and limitations of the manufacturing process. Small pore sizes were found to seriously complicate the elimination of excess slurry from the scaffold’s innermost pores. The effect of the strut/pore size on the mechanical performance of the scaffolds under compressive stresses was also evaluated, but no significant influence was found. Under compressive stresses, the structures resulted weaker when tested perpendicularly to the printing plane due to interlayer shear failure. Interlayer superficial grooves are proposed as potential failure-controlling defects, which could also explain the lack of a Weibull size effect on the mechanical strength of the fabricated DLP scaffolds.     

The Impact of PbF2-Based Glasses on Radiation Shielding and Mechanical Concepts: An Extensive Theoretical and Monte Carlo Simulation Study

Journal of Inorganic and Organometallic Polymers and Materials - This work aimed to investigate the impact of Lead-fluoride based glasses via theoretical and simulation techniques on mechanical and...     

Call admission control schemes: a review

Over the last few years, a substantial number of call admission control (CAC) schemes have been proposed for ATM networks. We review the salient features of some of these algorithms. Also, we quantitatively compare the performance of three of these schemes     

Transition to turbulence in rotating-disk boundary layers—convective and absolute instabilities

This work is an experimental study of mechanisms for transition to turbulence in the boundary layer on a rotating disk. In one case, the focus was on a triad resonance between pairs of traveling cross-flow modes and a stationary cross-flow mode. The other was on the temporal growth of traveling modes through a linear absolute instability mechanism first discovered by Lingwood (1995, J Fluid Mech 314:373–405). Both research directions made use of methods for introducing controlled initial disturbances. One used a distributed array of ink dots placed on the disk surface to enhance a narrow band of azimuthal and radial wave numbers of both stationary and traveling modes. The size of the dots was small so that the disturbances they produce were linear. Another approach introduced temporal disturbances by a short-duration air pulse from a hypodermic tube located above the disk and outside the boundary layer. Hot-wire sensors primarily sensitive to the azimuthal velocity component, were positioned at different spatial (r,θ) locations on the disk to document the growth of disturbances. Spatial correlation measurements were used with two simultaneous sensors to obtain wavenumber vectors. Cross-bicoherence was used to identify three-frequency phase locking. Ensemble averages conditioned on the air pulses revealed wave packets that evolved in time and space. The space–time evolution of the leading and trailing edges of the wave packets were followed past the critical radius for the absolute instability, r _{c A} . With documented linear amplitudes, the spreading of the disturbance wave packets did not continue to grow in time as r _{c A} was approached. Rather, the spreading of the trailing edge of the wave packet decelerated and asymptotically approached a constant. This result supports the linear DNS simulations of Davies and Carpenter (2003, J Fluid Mech 486:287–329) who concluded that the absolute instability mechanism does not result in a global mode, and that linear-disturbance wave packets are dominated by the convective instability. In contrast, wave-number matching between traveling cross-flow modes confirmed a triad resonance that lead to the growth of a low azimuthal number (n = 4) stationary mode. At transition, this mode had the largest amplitude. Signs of this mechanism can be found in past flow visualization of transition to turbulence in rotating disk flows.     

Bayes and classical estimation of environmental factors for thebinomial distribution

An environmental factor converts reliability test results at one environmental condition into equivalent “failure” information at other environments. This paper studies environmental-factor estimation for the binomial distribution. Under general conditions, Bayes point estimates and credibility limits for environmental factors are derived. Classical point and confidence interval estimates are introduced and compared with the Bayes estimators. The characteristics of Bayes and classical estimators for the binomial distribution are summarized through numerical computation and theoretical analysis. A numerical example of reliability assessment by means of environmental factors is presented     

Comments on “Distinguishability quantification of fuzzy sets”

This paper presents some comments on the above paper regarding the manipulation of Gaussian fuzzy sets and provides two useful generalized formulas for both of similarity and similarity/possibility relationships of Gaussian fuzzy sets with different widths.     

On an evolutionary approach for constrained optimization problem solving

Over the last few decades, many different evolutionary algorithms have been introduced for solving constrained optimization problems. However, due to the variability of problem characteristics, no single algorithm performs consistently over a range of problems. In this paper, instead of introducing another such algorithm, we propose an evolutionary framework that utilizes existing knowledge to make logical changes for better performance. The algorithmic aspects considered here are: the way of using search operators, dealing with feasibility, setting parameters, and refining solutions. The combined impact of such modifications is significant as has been shown by solving two sets of test problems: (i) a set of 24 test problems that were used for the CEC2006 constrained optimization competition and (ii) a second set of 36 test instances introduced for the CEC2010 constrained optimization competition. The results demonstrate that the proposed algorithm shows better performance in comparison to the state-of-the-art algorithms.     

Additive Behavior in Copper Electrorefining

This paper reports on the mode of action of two different organic additives—gelatine and thiourea—during the electrorefining of copper from acid copper sulfate solutions. Gelatine increases the cathode current efficiency and produces smoother deposits up to a certain level of concentration, beyond which, however, these effects are diminished by the steric hinderance of bulky molecular entities adsorbed to the electrode surface. Thiourea decreases the cathode current efficiency when present at concentrations around 5 mg/1. Nonetheless, it improves deposit quality. In higher concentrations, thiourea increases the cathodic current efficiency but also promotes nodule formation and rough deposits. The degradation and/or hydrolysis of both additives and the various interactions with the electrode surface and with cupric ions in solution are also examined.     

Combustion synthesis of NbC/ZrO2 composites: Influence of Cr additives on the microstructure and mechanical properties

Composites of NbC/ZrO₂ reinforced with different weight ratios of Cr metal were prepared by dynamic compaction combustion from a blend of Nb₂O₅–Zr–Cr powders. Factors controlling the synthesis process, the microstructure, and the mechanical properties of the samples, such as Cr wt% and the compression loads were studied. The samples were characterized by XRD, SEM, porosity, and hardness measurements. The porosity value of the sample with no additives was high and reached 31.6 vol%. A sudden decrease in the sample porosity to 2.4 vol % was noticed for the sample containing 3.0 wt% of Cr. A high-density sample with less than 2.0 vol % porosity and maximum hardness of 1038 HV was produced using 5.0 wt% Cr under 300 MPa compression load. Detailed thermodynamic calculations for the effect of Cr additives on the physicochemical properties of the system were introduced.