Role of Al2O3 layer in oxidation resistance of Cu-Al dilute alloys pre-annealed in H2 atmospheres

Copper was alloyed with small amounts of Al (0.2, 0.5, 1.0 and 2.0 mass%) to improve the oxidation resistance. Copper (6 N) and the Cu-Al alloys were oxidized at 773-1173 K in 0.1 MPa oxygen atmosphere after hydrogen annealing at 873 K. Continuous very thin Al₂O₃ layers were formed on the surface of all Cu-Al dilute alloys during the hydrogen annealing. Oxidation resistance of Cu-Al alloys was improved especially for Cu-2.0Al at 773-973 K, while it decreases on increasing the oxidation temperature. Cu-Al alloys followed the parabolic rate law at 1173 K, but most of other cases do not at and below 1073 K. Oxidation resistance for Cu-Al alloys was found relevant to the maintenance of the thin Al₂O₃ layer at the Cu₂O/Cu-Al alloy interface.     

Combined efficacy of nisin and pediocin with sodium lactate, citric acid, phytic acid, and potassium sorbate and EDTA in reducing the Listeria monocytogenes population of inoculated fresh-cut produce

The inability of chlorine to completely inactivate human bacterial pathogens on whole and fresh-cut produce suggests a need for other antimicrobial washing treatments. Nisin (50 microg/ml) and pediocin (100 AU/ml) individually or in combination with sodium lactate (2%), potassium sorbate (0.02%), phytic acid (0.02%), and citric acid (10 mM) were tested as possible sanitizer treatments for reducing the population of Listeria monocytogenes on cabbage, broccoli, and mung bean sprouts. Cabbage, broccoli, and mung bean sprouts were inoculated with a five-strain cocktail of L. monocytogenes at 4.61, 4.34, and 4.67 log CFU/g, respectively. Inoculated produce was left at room temperature (25 degrees C) for up to 4 h before antimicrobial treatment. Washing treatments were applied to inoculated produce for 1 min, and surviving bacterial populations were determined. When tested alone, all compounds resulted in 2.20- to 4.35-log reductions of L. monocytogenes on mung bean, cabbage, and broccoli, respectively. The combination treatments nisin-phytic acid and nisin-pediocin-phytic acid caused significant (P < 0.05) reductions of L. monocytogenes on cabbage and broccoli but not on mung bean sprouts. Pediocin treatment alone or in combination with any of the organic acid tested was more effective in reducing L. monocytogenes populations than the nisin treatment alone. Although none of the combination treatments completely eliminated the pathogen on the produce, the results suggest that some of the treatments evaluated in this study can be used to improve the microbial safety of fresh-cut cabbage, broccoli, and mung bean sprouts.     

Rubber‐toughened polyamide‐6 with a low thermal expansion coefficient: effect of preferential distribution of rubber and inorganic filler

The effects of morphological changes on the thermal expansion, toughness and heat resistance of polyamide‐6 (PA)/styrene–ethylene–butylene–styrene (SEBS)/polyphenylene ether (PPE) blends were investigated. Compared with the typical ‘sea (PA matrix)–island (PPE domain)–lake (SEBS in PPE domain)’ morphology, an injection‐molded ternary blend with a preferential distribution of SEBS component at the interface between PA and PPE exhibited a low coefficient of linear thermal expansion (CLTE) in the flow direction. This low CLTE was ascribed to the deformation of SEBS and PA into a co‐continuous microlayer network structure during injection molding. Consequently, the expansion preferentially occurred towards the thickness direction. Further CLTE reduction either by a change in PA viscosity or by the selective location of an inorganic filler was examined, and its influences on impact strength and heat resistance are discussed based on transmission electron microscopy observations. © 2015 Society of Chemical Industry     

The influence of side chains on formation of inclusion complexes prepared with polyolefin and cyclodextrins

We investigated the formation of inclusion complexes (ICs) between cyclodextrins (CDs) with different cavity size and polyolefin (PO) with different side chains by using Fourier transform infrared (FTIR) spectroscopy, wide-angle X-ray diffraction (WAXD) and differential scanning calorimetry. The analysis of FTIR spectra revealed that the resultants were complexes of CD and PO, and the analysis of WAXD revealed that the molecules of CD had a channel structure due to the formation of ICs. We found that IC could not be obtained when the cavity size of CD was small for PO molecules to thread and it was too large for cross-sectional area of PO molecules. Thus, it was found that PO1 with few side chains could form IC with α-CD, and PO2 with ethyl side chain could form IC with β-CD and γ-CD, while the PO3 with 2-methyl-propyl side chain could form IC with γ-CD. These results suggest that the cross-sectional areas of polymer and the cavity size of CDs play critical roles in the formation of ICs. It is only possible to form ICs when the polymer chains can tread into cavities of CDs, and the space between the polymer and CD is suitable to provide enough intermolecular interaction to keep the structure of IC stable.     

The evaporation and carburization behavior of coated systems of niobium on molybdenum and niobium on titanium

The evaporation, carburization and diffusion behavior of Nb-coated Mo and of Nb-coated Ti were investigated in order to estimate the surface characteristics of the coated systems. Nb layers were formed on Mo by both chemical and physical vapor deposition and on Ti by just physical vapor deposition. From the diffusion behavior, interdiffusion coefficients were obtained at 1860°C, 1980°C and 2080°C for the chemically vapor-deposited Nb/Mo system. From evaporation experiments it was found that simultaneous evaporation of Nb and Mo occured at about 2300°C for thick films of Nb on Mo. For thin films of Nb on Mo, the evaporation of both Nb and Mo was confirmed at 1900°C by ion microprobe analysis of the condensate. For Nb/Ti, rapid diffusion of Nb into Ti and evaporation of Ti similar to the case of Nb-Ti alloys were observed. From the carburization study, it was found that an Nb coating appreciably retards the carburization of Ti and Mo.     

Nucleation effect of inclusion complexes with different polyolefin as guest molecules on the crystallization of polypropylene

The γ‐cyclodextrin (γ‐CD) inclusion complexes (ICs) with four kinds of polyolefin (PO) as guest molecules were prepared. The crystallization behavior of isotactic polypropylene (iPP) blended with the γ‐CD and γ‐CD–PO ICs was investigated by differential scanning calorimetry, polarized optical microscopy, and light scattering. The iPP blended with the ICs was found to exhibit higher crystallization temperature (T_C), smaller spherulites, and faster crystallization rate than those of neat iPP, indicating that the ICs play a role of nucleating agent on the crystallization of iPP and induce accelerated crystallization. The IC with PO having higher T_C as guest molecules showed higher nucleation effect than the IC with PO having lower T_C as guest molecules. The results suggest that the nucleation effect of these ICs was affected by the kinds of the guest molecules. The higher T_C guest molecules could result in higher nucleation effect. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

The role of the msh homeobox gene during Drosophila neurogenesis: implication for the dorsoventral specification of the neuroectoderm

Development of the Drosophila central nervous system begins with the delamination of neural and glial precursors, called neuroblasts, from the neuroectoderm. An early and important step in the generation of neural diversity is the specification of individual neuroblasts according to their position. In this study, we describe the genetic analysis of the msh gene which is likely to play a role in this process. The msh/Msx genes are one of the most highly conserved families of homeobox genes. During vertebrate spinal cord development, Msx genes (Msx1-3) are regionally expressed in the dorsal portion of the developing neuroectoderm. Similarly in Drosophila, msh is expressed in two longitudinal bands that correspond to the dorsal half of the neuroectoderm, and subsequently in many dorsal neuroblasts and their progeny. We showed that Drosophila msh loss-of-function mutations led to cell fate alterations of neuroblasts formed in the dorsal aspect of the neuroectoderm, including a possible dorsal-to-ventral fate switch. Conversely, ectopic expression of msh in the entire neuroectoderm severely disrupted the proper development of the midline and ventral neuroblasts. The results provide the first in vivo evidence for the role of the msh/Msx genes in neural development, and support the notion that they may perform phylogenetically conserved functions in the dorsoventral patterning of the neuroectoderm.     

Precise analysis of H, C, N, and O as dominant impurities in Cu films: complementary use of SIMS and GDMS

Secondary ion mass spectrometry (SIMS) and glow discharge mass spectrometry (GDMS) were used to determine the impurity concentrations of hydrogen, carbon, nitrogen, and oxygen elements in Cu films, and the results of SIMS and GDMS were carefully interpreted. The Cu films were deposited on Si (100) substrates at substrate bias voltages ranging from 0 V to −150 V using a non-mass separated ion beam deposition method. From the results of SIMS using a Cs⁻ ion beam, as a whole, many high intensity peaks were observed in the Cu films deposited without substrate bias voltage. From the quantitative GDMS results, these peaks were determined to be signals detected as a cluster state such as C_xH_x, O_xH_x, C_xO_xH_x. Therefore, using a combination of these dominant impurities, all the unknown peaks observed in the SIMS results could be interpreted. Moreover, it was found that the dominant impurities having a great influence on the film purity were hydrogen, carbon, nitrogen, and oxygen.     

Vocal mechanics as the basis for phonosurgery

OBJECTIVE: A number of modifications in laryngoplastic phonosurgery have recently been proposed. This report is intended to clarify the concept on which the surgery should be based, vocal mechanics, for further rational development of the surgery. STUDY DESIGN: The results of various previous surgeries were compared. In an attempt to elucidate what makes the difference in the results, simulation of voice production was conducted with the use of excised larynges. METHODS: Excised larynges were mounted on a tube so as to be blown from below. Experimental variables in the model included the glottal area initially set, stiffness of the vocal folds, and subglottal pressure. The conditions under which the voice became hoarse were examined. RESULTS: The voice became hoarse under the following major conditions: 1) the initial glottal area exceeded a certain value, 2) stiffness was too high, and 3) the glottis was too tightly closed. Clinical representation for each condition was made, particularly for excessively tight glottal closure such as in spasmodic dysphonia. A new type of surgical treatment for spasmodic dysphonia, lateralization thyroplasty, was briefly reported, which restored the voice to normal without recurrence for 1 year at the time of this writing. CONCLUSIONS: A potential new type of laryngoplastic phonosurgery should be conformed to the mechanics of voice production. In treating dysphonia, it is often necessary to switch from etiologic or radical treatment, if infertile, to symptomatic treatment instead, at the level of mechanics.