Improved atrial function in bicaval versus standard orthotopic techniques in cardiac transplantation

Atrial geometry is preserved in the bicaval technique of cardiac transplantation. Using Doppler echocardiography, we investigated the impact of this technique on preservation of atrial function and found that echocardiographic indexes of atrial function are improved in bicaval cardiac transplants versus the standard orthotopic transplants.     

Aortic valve papillary fibroelastoma. A diagnosis by transthoracic echocardiography

Cardiac papillary fibroelastomas are unusual, frond-like growths typically found on cardiac valves, diagnosed incidentally on autopsy or cardiac surgery, but rarely during life. We report a rare case of an aortic valve papillary fibroelastoma detected by transthoracic echocardiography and confirmed by histologic study.     

Radiation detector made of a high-quality polycrystalline diamond

Radiation detector was made of a high-quality CVD polycrystalline diamond composed of frost column like structure diamond grains, and induced charge distribution spectra and drift velocities were measured by using alpha particles. As a result, the CVD polycrystalline achieved maximum induced charge of 83% of HP/HT type IIa diamond. Moreover, the CVD crystal had lower charge loss on electrons compared with the HP/HT type IIa diamond. Drift velocities of electrons and holes were v_e = 7.7 × 10⁴ and v_h = 7.3 × 10⁴cm/s at an electric field of 20 kV/cm, respectively. In addition, response function measurement for 14 MeV neutrons was carried out.     

A feasibility study of a direct-mapping parallel processing method to solve linear equations in load-flow calculation

With the growing size and complexity of power systems, system analysis—such as transients calculation—takes much time. Hence, fast calculation methods are required. Although parallel processing is a hopeful method, there have been difficulties in the parallel solution of linear equations which appear in power-flow calculations by the Newton-Raphson method. This paper aims at the fast calculation of the power-flow problem by means of parallel processing. In order to improve the suitability to the parallel solution of the differential equation in transients calculation, we assume the use of a direct-mapping parallel processing machine to map directly the network of a power system onto a network of processors. Under this assumption, we propose a new parallel-processing-oriented method in which the linear equation is solved by linear iterations between nodes with Aitken acceleration. We simulate the method on three model power systems and compare this Parallel Iterative Method (PIN) with a Parallel Direct Method (PDM) which uses the banded matrix according to the number of operations required. As a result, we can expect that PIM may solve linear equations faster than PDM with m processors, although the PIM might be inferior to the PDM with m × m processors, where m denotes the half-band width of the banded matrix.     

A radix-8 wafer scale FFT processor

Wafer Scale Integration promises radical improvements in the performance of digital signal processing systems. This paper describes the design of a radix-8 systolic (pipeline) fast Fourier transform processor for implementation with wafer scale integration. By the use of the radix-8 FFT butterfly wafer that is currently under development, continuous data rates of 160 MSPS are anticipated for FFTs of up to 4096 points with 16-bit fixed point data.     

Observation of single-walled carbon nanotubes by photoemission microscopy

Single-walled carbon nanotube networks grown on SiO₂ pillars were studied by means of scanning photoemission microscopy. The individual nanotubes or nanotube bundles growing from the pillar tops were observed in C 1s images. Band bending near catalytic Fe/nanotube contacts in an end-bonded configuration was studied by measuring C 1s spectra along the tube axes. Within our experimental resolution, no band bending was observed. This implies that the depletion width is less than the spatial resolution of the scanning photoemission microscope (90 nm) or that the amount of the band bending is less than 0.1 eV.     

Preparation and characterization of electroplated amorphous gold-nickel alloy film for electrical contact applications

A process for electroplating amorphous gold-nickel alloy with the atomic ratio of unity was developed. The plating bath was prepared by adding potassium cyanoaurate(I) into a known plating bath which produces amorphous nickel-tungsten alloy. At a sufficiently high gold concentration, the alloy deposit did not contain any tungsten. The amorphous nature of the Au-Ni alloy produced in the new bath was confirmed by using TEM and THEED. Hardness, resistivity, and contact resistance of this new alloy were determined, and the results are discussed for applications as an electrical contact material.     

Generalized measuring-worm algorithm: high-accuracy mapping and movement via cooperating swarm robots

Recently, many extensive studies have been conducted on robot control via self-positioning estimation techniques. In the simultaneous localization and mapping (SLAM) method, which is one approach to self-positioning estimation, robots generally use both autonomous position information from internal sensors and observed information on external landmarks. SLAM can yield higher accuracy positioning estimations depending on the number of landmarks; however, this technique involves a degree of uncertainty and has a high computational cost, because it utilizes image processing to detect and recognize landmarks. To overcome this problem, we propose a state-of-the-art method called a generalized measuring-worm (GMW) algorithm for map creation and position estimation, which uses multiple cooperating robots that serve as moving landmarks for each other. This approach allows problems of uncertainty and computational cost to be overcome, because a robot must find only a simple two-dimensional marker rather than feature-point landmarks. In the GMW method, the robots are given a two-dimensional marker of known shape and size and use a front-positioned camera to determine the marker distance and direction. The robots use this information to estimate each other’s positions and to calibrate their movement. To evaluate the proposed method experimentally, we fabricated two real robots and observed their behavior in an indoor environment. The experimental results revealed that the distance measurement and control error could be reduced to less than 3 %.     

Effect of mechanical properties of material on rate of fatigue crack propagation

Many experimental and analytical equations on a rate of a fatigue crack propagation have been proposed. However, it seems that they can not fully express its complex behavior. There are still many problems remaining to be solved in order to clarify its mechanism. One of them is to clarify the relation between the rate of the crack propagation and the mechanical properties of material. In this paper, the rate of the crack propagation is analysed to clarify this problem. This analysis is based on the observation results of the fatigue crack propagation behavior previously by the authors. The analytical result is compared with the experimental one to make sure that they agree with each other. The conclusion obtained is; the rate of fatigue crack propagation is expressed by using the stress intensity factors as

$\text{dl}\text{dN}\text{= {}\text{c}\text{[Y}{}^2\text{F}{}^{\mathrm{a}}\text{E}{}^{\mathrm{a(1?n)}}\text{]}\text{} (K}{}_{\max }\text{)}{}^2\text{(K}{}_{\mathrm{a}}\text{)}{}^{\mathrm{a(2?n)}}$

. where C is a constant; E, Young's modulus; F, plastic coefficient; Y, yield stress; K_max and K_a, maximum and amplitude of the stress intensity factor, and α and n, exponents of the Manson-Coffin's law and work-hardening.