Transient liquid phase sintering of high-purity mullite for high-temperature structural ceramics

High-purity mullite ceramics, promising engineering ceramics for high-temperature applications, were fabricated using transient liquid phase sintering to improve their high-temperature mechanical properties. Small amounts of ultrafine alumina or silica powders were uniformly mixed with the mullite precursor depending on the silica-alumina ratio of the resulting ceramics to allow for the formation of a transient liquid phase during sintering, thus, enhancing densification at the early stage of sintering and mullite formation by the reaction between additional alumina and the residual glassy phase (mullitization) at the final stage of sintering. The addition of alumina powder to the silica-rich mullite precursor resulted in a reaction between the glassy silica and alumina phases during sintering, thereby forming a mullite phase without inhibiting densification. The addition of fine silica powder to the mullite single-phase precursor led to densification with an abnormal grain growth of mullite, whereas some of the added silica remained as a glassy phase after sintering. The resulting mullite ceramics prepared using different powder compositions showed different sintering behaviors, depending on the amount of alumina added. Upon selecting an optimum process and the amount of alumina to be added, the pure mullite ceramics obtained via transient liquid phase sintering exhibited high density (approximately 99%) and excellent high-temperature flexural strength (approximately 320 MPa) at 1500 °C in air. These results clearly demonstrate that pure mullite ceramics fabricated via transient liquid phase sintering with compositions close to those of stoichiometric mullite could be a promising process for the fabrication of high-temperature structural ceramics used in an ambient atmosphere. The transient liquid phase sintering process proposed in this study could be a powerful processing tool that allows for the preparation of superior high-temperature structural ceramics used in the ambient processing atmosphere.     

Dielectric relaxation of vegetable-based polyurethane

Vegetable-based polyurethane (PU) was prepared in the thin film form by spin coating. This polymer is synthesised from castor oil, which can be extracted from the seeds of a native plant in Brazil called mamona. This polymer is biocompatible and is being used as material for artificial bone. The PU was characterised by dielectric spectroscopy in a wide range of frequency (10^–5 Hz to 10⁵ Hz) and by thermally stimulated discharge current (TSDC) measurements. The glass transition temperature (T _g = 39°C) was determined and using the initial rise method the activation energy was found to be 1.58 eV.     

超低失真多层陶瓷电容相较于薄膜电容的优势

在滤波应用中,超低失真的表面贴装多层陶瓷电容(MLCC),已经成为模拟电路设计者在SMD塑料薄膜(薄膜片式)电容之外的另一种选择,它的体积更小、成本更低、也更为可靠。这些潜在的模拟电路应用实例包括:音响设备、无线设备、锁相环(PLL)和通信设备(如调制/解调器)等。这些新型电容的等效串连电阻(ESR)极低,因此非常适合于高效率的DC/DC变换器和高速微处理器应用。低失真电容的应用随着处理器速度的提高和工作电压的降低,噪声会给信号完整性带来严重的影响,除非能通过过滤或解耦的办法将其去除。在声频、射频、PLL和通信电路中,跟踪误差…     

Analysis of the genes encoding the variable regions of human IgG rheumatoid factor

OBJECTIVE: To better understand the immunoglobulin variable (V) region repertoire of rheumatoid factors (RF). METHODS: We characterized the heavy (H) and light (L) chain gene segments utilized in a monospecific IgG RF secreting hybridoma (AEE111F) which were derived from a patient with rheumatoid arthritis (RA). The hybridoma was established by fusion of a mouse myeloma cell line with bone marrow derived mononuclear cells from a patient with RA. First strand complementary DNA (cDNA) was generated and used for a polymerase chain reaction amplification of the H and L chain V domains. The amplified V domains were sequenced and compared with an extensive database of germline and cDNA V gene segments. RESULTS: The VH sequence was found to be 96% homologous to a previously described fetal VH3 cDNA (60P2). The VL sequence was also highly homologous to the previously described V lambda II gene (96%) derived from a patient with systemic lupus erythematosus which correlated with an 8.12 idiotype (Id), and to an antibacterial antibody against the Haemophilus influenzae type b capsular polysaccharide (94.7%). CONCLUSION: The overlap among this RF VL gene and the 2 reported V lambda sequences of antibodies that expressed anti-DNA related Id and an environmental pathogen specificity suggests that a part of the IgG RF isolated from patients with RA may thus be derived from the physiological natural antibody repertoire during an abnormal immune response and then develop high affinity, monospecific RF by the selection of an antigen driven mechanism.     

On A Maximum Likelihood Method for Clustering

Behaviormetrika - In this paper, we propose a new clustering method based on the concept of maximum likelihood (ML) estimation. In general, the problem of local minima arises when we try to use the...     

Hierarchical Clustering Method Using Probabilistic Similarity Measure

In this paper, we propose a new hierarchical clustering method, which is useful to find appropriate clusters of attributes from given dichotomous or frequency data. Important features of our method are 1) the similarity between two attributes is defined as a probability of their pattern vectors being observed under the hypothesis of independence, 2) for each generated cluster, one pattern vector is defined in a natural manner, and 3) it can be used freely without distinguishing the frequency data from the dichotomous one.

A typical frequency data is analyzed to illustrate how our method works effectively. The discussion on similarities among objects is also included to propose a new similarity measure based on our clustering method.

     

Near-zone gain of open-ended rectangular waveguides

Full-wave solutions to the problem of radiation by open-ended rectangular waveguides (OEG) are presented. The radiation problem is formulated in terms of an electric field integral equation (EFIE). The EFIE is solved using the method of moments for three OEG antennas covering the frequency range from 200 to 750 MHz. Results for the near-zone gains as a function of both frequency and distance from the OEG aperture are presented. Estimates for uncertainties in the calculated gain are also given     

Relationship Between Local Atomic Arrangements and Properties of High-T c Superconductive Copper Oxides

Here various approaches to understanding the complex relationship among the local atomic arrangements, the distribution of charge/holes and the superconductivity characteristics are discussed for a variety of multi-layered copper-oxide superconductors. Regarding the structural parameters, i.e. bond lengths and angles, no single parameter is revealed to control the superconductivity characteristics alone. As a matter of fact, superconductivity properties are found to be correlated with the whole delicately balanced fine-structure that is described by a set of multiple parameters: it is shown that T _c and H_irr are enhanced in somewhat opposite ways. Expressing the delicately balanced fine-structure through the charge/hole distribution, it is concluded that the more homogeneously distributed the charge carriers are the more enhanced is the H_irr characteristics, while the opposite is likely to apply to the T _c value.     

The Michigan benchmark: towards XML query performance diagnostics

We propose a micro-benchmark for XML data management to aid engineers in designing improved XML processing engines. This benchmark is inherently different from application-level benchmarks, which are designed to help users choose between alternative products. We primarily attempt to capture the rich variety of data structures and distributions possible in XML, and to isolate their effects, without imitating any particular application. The benchmark specifies a single data set against which carefully specified queries can be used to evaluate system performance for XML data with various characteristics.     

Preparation and characterization of porous and electrically conducting carbon-clay composites

Porous and electrically conducting carbon-clay composites were prepared by firing mixtures of carbon powder (0 to 20 wt%) and clay minerals. They showed porosity of 50 to 65% and had high mechanical strength (compressive strength = 130 to 400 kg cm^–2) as well as high resistance against thermal oxidation in air. Their electrical conductivity, , increased with increasing carbon content levelling off at about 20 wt% of carbon content to give a value of about 2 S cm^–1. Formation of carbon chains is considered to be responsible for the electrical conduction in the composite, and a model to correlate the electrical conductivity with the carbon content has been proposed by modifying a model previously proposed by Scarisbrick.