Efficiency of repeated batch penicillin fermentation using two fermentors. Computer simulation and optimisation

Repeated batch operation using two fermentors (RBTF) to penicillin fermentation was demonstrated by computer simulation to improve productivity. Three operation modes were compared: chemostat, repeated batch operation using a single fermentor (RBSF) and RBTF; in each case account was made of the lag period before growth. The simulated fermentor performances were assessed on the basis of the penicillin productivity and concentration; the simulation was based on published batch fermentation data. It was shown that RBTF was superior to RBSF and chemostat. The advantage of RBTF increased as the lag period became greater.     

Comparison of activities in selective catalytic reduction of NOx by C3H8 over Co/MFI, Fe/MFI, and H/MFI zeolite catalysts

The Co/MFI(SiO₂/Al₂O₃ = 30) were prepared by a precipitation method with NaOCl in alkali solutions exhibited high activities to N₂ at 250 °C for the selective catalytic reduction (SCR) of NO_x. These catalysts showed two UV–vis bands at 700 and 400 nm, indicating the presence of octahedral Co(III) as well as tetrahedral Co(II). The high SCR activity over such Co(III, II)/MFI(30) seems to come from Co(III)---O moieties. The Co(II)MFI(30) catalysts prepared from Co(II)Cl₂ exhibited low SCR activities due to the presence of tetrahedral Co(II) ions in MFI. Less CO formation occurred over Co/MFI catalysts. The Fe/MFI(30) catalyst exhibited high activity due to the presence of some Fe---O species in MFI but more amount of CO were produced during SCR. H/MFI(30) catalyst exhibited a good SCR activity. However, more amount of carbonaceous deposits were produced on it. The correlation between acid concentration and SCR activity was discussed over H/MFIs.     

Periodic limb movement disorder in neuroleptic-induced akathisia

We recorded all-night polysomnograms of four schizophrenic patients with neuroleptic-induced akathisia (NIA) before and during treatment with clonazepam. Also, four non-akathitic schizophrenic patients were recorded all-night polysomnograms as control subjects. Daily treatment with 1.5 to 3 mg clonazepam improved subjective complaints of all the 4 patients with NIA. Three of 4 patients with NIA exhibited periodic limb movements (PLM) on bilateral legs, but none of 4 control subjects showed PLM. Total number of PLM and PLM per hour decreased during clonazepam treatment. Moreover, mean inter-movement intervals of PLM of 3 patients were prolonged on bilateral legs. NIA might change its feature as PLM during night sleep.     

Preferential Oxidation of CO in H2-Rich Gas at Low Temperatures over Au Nanoparticles Supported on Metal Oxides

We investigated Au catalysts supported on TiO₂, Fe₂O₃, and ZnO for their preferential oxidation of CO in a H₂-rich atmosphere. Both full conversion and selectivity were achieved over Au/Fe₂O₃ and Au/ZnO around room temperature, but at higher temperatures the CO conversion was suppressed due to competition between CO and H₂.     

A novel on-chip electrostatic discharge (ESD) protection withcommon discharge line for high-speed CMOS LSIs

A novel on-chip electrostatic discharge (ESD) protection for high-speed CMOS LSI's that operate at higher than 500 MHz has been developed. Introduction of a newly developed common discharge line (CDL) can completely eliminate the protection device influence on the inner circuit operation. This enables minimization of the I/O capacitance by shrinking the dimension of the output transistor, which also serves as a protection device in conventional devices. This new protection (CDL protection) was applied to a high-speed DRAM of which I/O pin capacitance specification is 2 pF. As a result, the ESD tolerance of 4 kV for the charged device model test, 4 kV for the human body model test, and 700 V for the machine model test were obtained. In addition, the DRAM data rate higher than 660 MHz at room temperature was achieved. The results show significant improvement for both ESD and the I/O capacitance, compared with the conventional structure     

Development of a distributed sensing technique using Brillouinscattering

This paper reviews the developments of a distributed strain and temperature sensing technique that uses Brillouin scattering in single-mode optical fibers. This technique is based on strain- and temperature-induced changes in the Brillouin frequency shift. Several approaches for measuring the weak Brillouin line are compared     

Preparation of SiB4±x and SiB6 plates by chemical vapour deposition of SiCl4 + B2H6 system

SiB_4±x and SiB₆ plates were prepared by chemical vapour deposition (CVD) using SiCl₄, B₂H₆ and H₂ gases under the conditions of deposition temperatures (T _dep) from 1323–1773 K, total gas pressures (P _tot) from 4–40 kPa and B/Si source gas ratio (m _B/Si=2B₂H₆/SiCl₄) from 0.2–2.8. The effects of CVD conditions on the morphology, structure and composition of the deposits were examined. High-purity and high-density SiB_4±x and SiB₆ plates about 1 mm thick were obtained at the deposition rates of 71 and 47 nm s⁻¹, respectively. The lattice parameter, composition and density of CVD SiB_4±x plates were dependent on their non-stoichiometry. The lattice parameter,a, was 0.6325 nm, butc ranged from 1.262–1.271 nm.The B/Si atomic ratio ranged from 3.1–5.0, and the density ranged from 2.39–2.45×10³ kg m⁻³. The CVD SiB₆ plates showed constant values of lattice parameters (a=1.444 nm,b=1.828 nm,c=0.9915 nm), composition (B/Si=6.0) and density (2.42×10³ kg m⁻³), independent of CVD conditions.     

Loss distribution measurement of silica-based waveguides by using ajaggedness-free optical low coherence reflectometer

The loss distributions in silica-based waveguides are successfully measured using a jaggedness-free optical reflectometer (OLCR). The OLCR reduces jagged fluctuations which appear in Rayleigh backscattering measurements undertaken with conventional OLCRs to within ±1 dB by averaging the wavelength-dependent Rayleigh backscatter signals. Constant loss distributions and a step-like loss increase in the waveguides were clearly observed     

An efficient method for developing requirement specifications for plant control software using a component-based software prototype

This paper proposes an efficient method to develop requirement specifications for Plant Control Software (PCSW) using software-component-based prototypes. Prior to this proposal, domain analyses were conducted on existing PCSWs, and their functions were classified into “similar functions” and “individual functions”. Then PCSW Software Components (PSC: PCSW Software Component, PSCs: PCSW Software Components) were developed to correspond to these functions. PSCs as parameter-style components were developed in order to satisfy the clients’ (we define clients as owners, managers and operators of plants) requirements. A support environment for developing requirement specifications was developed. The environment consists of the Prototype Development Tool (PDT), the Behavior Check Simulator (BCS) and the Requirement Specification Development Tool (RSDT). The method consists of four steps. In the first step, PDT is used to define the parameters to customize PSCs and to compose a PCSW prototype by setting these parameters to PSCs. In the second step, BCS is used to execute the composed PCSW prototype and check its behavior and relevancy against the clients’ expectations. In the third step, steps 1 and 2 are repeated until the behavior of the PCSW prototype satisfies the clients’ requirements. Finally, a requirement specification is developed from the PCSW prototype which fully reflects the clients’ requirements. In order to evaluate the proposed method, it has been applied in five development cases. A Requirement Coverage of 91%, a Requirement Revision Rate of 6%, a PSC Reuse Rate of 92% and a LOC Reuse Rate of 83% have been achieved. In addition, a reduction of 55% in the amount of time required to develop requirement specifications has been achieved. These results indicate that the proposed method has sufficient capability to develop an exhaustive and an adequate PCSW requirement specification. And the developed PSCs have sufficient functions and capability to compose PCSW prototypes, and the support environment is capable of shortening the time taken to develop requirement specifications.     

Direct dispersion measurement of highly-erbium-doped optical amplifiers using a low coherence reflectometer coupled with dispersive fourier spectroscopy

The group delay and dispersion, including the erbium ion contributions, of the highly erbium-doped silica planar waveguide amplifier and multicomponent glass fibre amplifiers are directly measured at different pump powers using a low coherence reflectometer and dispersive Fourier spectroscopy. This method derives the refractive index spectra of these amplifiers directly from the produced reflectograms without any physical or mathematical assumptions. The dispersion of the planar waveguide amplifier at 500 mW pumping changes between +300 and -200 ps/km/nm with a 0.4 wt.% erbium concentration.<>