Dye adsorption characteristics of alginate/polyaspartate hydrogels

This study examined the removal of some basic dyes, such as Methylene Blue, Malachite Green and Methyl Orange, using alginate or alginate/polyaspartate composite gel beads. The adsorption of dyes from aqueous solutions at 25 °C was examined using a batch sorption technique. The effects of CaCl₂ and the dye concentration on the adsorption were examined. Type-S adsorption isotherms were obtained, which is characteristic of a weak solute–solid interaction. The ionic interaction between the dye molecule and gel matrix appears to be responsible for the efficient adsorption of cationic dyes in this system. These results suggest that an alginate/polyaspartate gel can be used as an effective sorbent for water pollutants such as dyes, and the immobilization of these organic contaminants in the hydrogels from wastewater can solve one of the most important environmental problems in the related industry.     

Compact Dipole Antenna for Terrestrial Digital Multimedia Broadcasting Service

A compact dipole antenna for the terrestrial digital multimedia broadcasting (TDMB) application is presented. The length of the antenna is about 0.06λ at the TDMB resonance frequency of 190 MHz. Miniaturization of the antenna is achieved by using meander structures and lumped elements. The proposed antenna has two resonance frequencies and covers the TDMB band from 174 MHz to 216 MHz in Korea. The antenna has good impedance bandwidth and radiation characteristics for the TDMB. The experimental results of the designed dipole antenna are presented and analyzed.     

89-GHz fT room-temperature silicon MOSFETs

The authors report the implementation of deep-submicrometer Si MOSFETs that at room temperature have a unity-current-gain cutoff frequency (f_T) of 89 GHz, for a drain-to-source bias of 1.5 V, a gate-to-source bias of 1 V, a gate oxide thickness of 40 Å, and a channel length of 0.15 μm. The fabrication procedure is mostly conventional, except for the e-beam defined gates. The speed performance is achieved through an intrinsic transit time of only 1.8 ps across the active device region     

Efficiency increase of an induction motor by improving coolingperformance

Improving the efficiency of induction motors, which are the most energy consuming electric machines in the world, saves much energy. The efficiency can be increased by improving cooling performance as well as by using better materials or by improving electromagnetic performance with better design. This paper presents the relationship between the efficiency or the losses and the temperature of coils with experiments as well as simulations by changing parameters such as the load and the flow rate of cooling air. The losses and the efficiency are calculated from an equivalent circuit method as well as experiments. Coil temperatures variation affects much on the efficiency. The internal cooling method is better than that of external cooling for the coil temperature reduction. Several cooling methods are compared focusing on the fan efficiency and performance, from which the values of the efficiencies of the motors are expected. The fan efficiency as well as the fan performance should be considered for the optimum fan design to increase the total efficiency of a motor. The simulations are validated by the comparison with the experiments     

Performance of asynchronous DS-CDMA using a maximal ratio combiningdiversity over a Rician fading channel

The final closed-form expression for bit error probability (BEP) is presented for a DS-CDMA system using a maximal ratio combining (MRC) diversity over a Rician fading channel. The accuracy of the BEP estimate evaluated by this expression is verified by comparison with a semi-analytic simulation result. The effect that diversity order has on the BEP is also considered for typical multipath delay profiles with different Rician ratios     

PGT: news recommendation coalescing personal and global temporal preferences

Knowledge and Information Systems - Given sequential news watch logs of users, how can we accurately recommend news articles? Compared to other items (e.g., movies and e-commerce products) for a...     

An investigation into vehicle rollover prevention by coordinated control of active anti-roll bar and electronic stability program

This paper presents a method for designing a controller that uses an active anti-roll bar (AARB) and an electronic stability program (ESP) for rollover prevention. ESP with longitudinal speed control (LSC) can carry out active braking to reduce vehicle speed and lateral acceleration to prevent a rollover. To enhance the rollover prevention capability of the ESP, an AARB is adopted. The controller for the AARB was designed based on linear quadratic (LQ) static output feedback (SOF) control methodology, which attenuates the effect of lateral acceleration on the roll angle and roll rate by control of the suspension stroke and the tire deflection of the vehicle. Although this AARB significantly increases ride comfort and rollover prevention, it has a drawback — the vehicle loses its maneuverability. Therefore, the ESP with LSC is used to overcome this drawback. Simulations showed that the proposed method was effective in preventing a rollover.     

Magnetic mechanical capsule robot for multiple locomotion mechanisms

This paper proposes a magnetic mechanical capsule robot which crawls in a fluid-filled tube. The developed capsule robot employs two locomotion mechanisms simultaneously. It has spiral ribs at both ends, which are rotated by a small on-board motor. Such rotating spiral structures generate a driving force of the capsule robot. We invented a magnetic mechanical mechanism to transfer the rotational motion of the frontal part into the linear motion of the middle part. Using this original mechanism, the linearly moving part at the middle of the capsule robot generates a supportive driving force. The improved mobility is evaluated in experiments. The developed capsule robot employing multiple locomotion mechanisms moves 44% faster than the spiral motion-based capsule robot. The developed magnetic mechanical mechanism and the mobile robotic platform could be used for pipe inspection robots or medical robots.     

Leakage current in a Si-based nanopore structure and its influence on noise characteristics

We have measured leakage current in a silicon substrate-based nanopore membrane device immersed in an aqueous environment which typically shows the current level of few nA. This current level is compared with the measured current density (400 nA/cm² at 1 V) from the pristine Si wafer (p-type, 10¹⁶/cm³ boron doping) indicating that the exposed Si surface in a nanopore membrane device acts as an electrochemical reaction site. The leakage current is drastically reduced from >10 nA to <100 pA at 1 V by the deposition of a dielectric layer to the Si-based nanopore membrane device. We also noted that the root-mean-square noise of the ionic current is also reduced from 38 to 28 pA in correlation with the reduction of leakage current, indicating that electrochemical reaction provides one of the major sources of noise.     

Influence of wall charge distribution on time lag of address discharge in AC plasma display panels

The influence of wall charge distribution on the time lag of address discharge in an AC plasma display panel is investigated using two different reset waveforms: one (typical reset) induces both face and surface discharges and the other (TR reset) induces face discharges only. The measured formative time lag and statistical time lag of address discharge for TR were 21–31 ns and 31–74 ns shorter than the one for the typical reset, respectively. The TR reset resulted in much less increase of statistical time lag than the typical reset when the reset-to-address time interval was increased, and 70 ns smaller deviation of the statistical time lag among different color cells. Calculations show that the TR reset forms a much smoother wall charge profile, which is less susceptible to cell parameter variations, than the typical reset. The observed differences in the time lags of address discharge between different scan lines and color cells are strongly correlated to the differences of the wall charge profile, indicating that a smooth wall charge profile formed by the reset using face discharges only reduces the time lag of address discharge and minimizes the susceptibility of address discharge to cell parameter variation.