On the variation with flux and frequency of the core loss coefficients in electrical machines

A model of core losses, in which the hysteresis coefficients are variable with the frequency and induction (flux density) and the eddy-current and excess loss coefficients are variable only with the induction, is proposed. A procedure for identifying the model coefficients from multifrequency Epstein tests is described, and examples are provided for three typical grades of non-grain-oriented laminated steel suitable for electric motor manufacturing. Over a wide range of frequencies between 20-400 Hz and inductions from 0.05 to 2 T, the new model yielded much lower errors for the specific core losses than conventional models. The applicability of the model for electric machine analysis is also discussed, and examples from an interior permanent-magnet and an induction motor are included.     

Stable Isomers of Sila - and Germadodecahedrane. a Semiempirical (Am1) Investigation of the Structure of 4/6 and 4/5/6 Ring Containing E20 (E=SI, GE) Systems

AMI molecular orbital calculations with full geometry optimisation of 4/6, 5/5 and 4/5/6 isomers of E₂₀ (E=Si, Ge) show a clear preference of germanium to be accommodated in four membered rings and to achieve coordination numbers greater than 3 (V A). as a consequence, unlike C₂₀ or Si₂₀, the dodecahedral form of Ge₂₀ was not localised on the potential surface, instead an opened structure derived from an octagermaprismane (IV B) can be predicted. Notable kinetic stabilisation in the (SiR)₂₀ systems is suggested by the HOMO-LUMO differences.     

Inulin mixed esters crosslinked with 2-ethyl-hexyl-acrylate and their promotion as bio-based materials

New inulin-based materials were obtained by graft-copolymerization of inulin (poly-β(1 → 2)-fructoside) with 2-ethyl-hexyl acrylate. Inulin mixed esters were first synthesized by acylation using methacryloyl and palmitoyl chlorides. Further, these esters were copolymerized with 2-ethyl-hexyl acrylate in order to obtain bio-based crosslinked materials that could be used as commodity plastics and that would have biodegradable properties. The obtained products were characterized using FT-IR and ¹H NMR spectroscopies, thermogravimetry; differential scanning calorimetry, and activation energy for the degradation processes (using Kissinger method) was calculated. These biomaterials were also subjected to density measurement, tensile and torsion tests to evaluate their mechanical properties.     

Organic phase PPO biosensor based on hydrophilic films of electropolymerized polypyrrole

We described herein, the construction of an organic phase enzyme electrode (OPEE) via polyphenol oxidase (PPO) entrapment within a hydrophilic polypyrrole film electrogenerated from on a new bispyrrolic derivative (1) containing a long hydrophilic spacer. The so-called “adsorption step procedure” was adopted for the preparation of the organic phase PPO biosensor. The amperometric detection of catechol was carried out in anhydrous chloroform at −0.2 V versus Ag/AgCl. The electroanalytical parameters of the biosensor strongly depend on its configuration and on the hydration state of the enzyme matrix. The best sensitivity obtained for catechol in chloroform was 15.6 mA M⁻¹ cm⁻².     

Kinetic characterization of Prussian Blue-modified graphite electrodes for amperometric detection of hydrogen peroxide

Prussian Blue-modified graphite electrodes (G/PB) with electrocatalytic activity toward H₂O₂ reduction were obtained by PB potentiostatic electrodeposition from a mixture containing 2.5 mm FeCl₃ + 2.5 mm K₃[Fe(CN)₆] + 0.1 m KCl + 0.1 m HCl. From cyclic voltammetric measurements, performed in KCl aqueous solutions of different concentrations (5 × 10⁻²–1 m), the rate constant for the heterogeneous electron transfer (k _s) was estimated by using the Laviron treatment. The highest k_s value (10.7 s⁻¹) was found for 1 m KCl solution. The differences between the electrochemical parameters of the voltammetric response, as well as the shift of the formal potential, observed in the presence of Cl⁻ and NO₃⁻ compared to those observed in the presence of SO₄²⁻ ions, points to the involvement of anions in the redox reactions of PB. The G/PB electrodes showed a good electrochemical stability proved by a low deactivation rate constant (0.8 × 10⁻¹² mol cm² s⁻¹). The electrocatalytic efficiency, estimated as the ratio , was found to be 3.6 (at an applied potential of 0 mV vs. SCE; Γ = 5 × 10⁻⁸ mol cm⁻²) for a H₂O₂ concentration of 5 mm, thus indicating G/PB electrodes as possible H₂O₂ sensors.     

Development and characterisation of microporous biomimetic scaffolds loaded with magnetic nanoparticles as bone repairing material

Fine-tuning of the scaffolds structural features for bone tissue engineering can be an efficient approach to regulate the specific response of the osteoblasts. Here, we loaded magnetic nanoparticles aka superparamagnetic iron oxide nanoparticles (SPIONs) into 3D composite scaffolds based on biological macromolecules (chitosan, collagen, hyaluronic acid) and calcium phosphates for potential applications in bone regeneration, using a biomimetic approach. We assessed the effects of organic (chitosan/collagen/hyaluronic acid) and inorganic (calcium phosphates, SPIONs) phase over the final features of the magnetic scaffolds (MS). Mechanical properties, magnetic susceptibility and biological fluids retention are strongly dependent on the final composition of MS and within the recommended range for application in bone regeneration. The MS architecture/pore size can be made bespoken through changes of the final organic/inorganic ratio. The scaffolds undertake mild degradation as the presence of inorganic components hinders the enzyme catalytic activity. In vitro studies indicated that osteoblasts (SaOS-2) on MS9 had similar cell behaviour activity in comparison with the TCP control. In vivo data showed an evident development of integration and resorption of the MS composites with low inflammation activity. Current findings suggest that the combination of SPIONs into 3D composite scaffolds can be a promising toolkit for bone regeneration.