Value of information in remanufacturing complex products

Remanufacturing facilities usually face a trade-off between limited information about remanufacturing yields and potentially long supplier lead times. To improve production performance, these firms may attempt to acquire more timely and accurate information about remanufacturing yields or alternatively, to reduce the lead times of purchased parts. We develop four decision-making models to evaluate the impact of yield information and supplier lead time on manufacturing costs. We identify the operating conditions under which these capabilities are valuable, along with their relative impact on facility performance. Each model is formulated as an infinite horizon, stochastic dynamic program (Markov decision process). Our results indicate that the yield information is generally quite valuable, while investments in supplier responsiveness provide trivial returns to products with few parts. However, as product complexity increases with large number of target parts, the value of short lead times increases.     

Application of novel extractants for actinide(III)/ lanthanide(III) separation in hollow-fibre modules

Separation tests using hollow-fibre modules were performed for the difficult selective extraction of trivalent actinides over fission lanthanides from acidic media. This article shows that with 2,6-di(5,6-dipropyl-1,2,4-triazin-3-yl)pyridine as the extractant, up to 94% americium could be extracted from 1.0 kmol/m³ HNO₃, with minimal lanthanide co-extraction. Using a synergistic mixture of bis(chlorophenyl)dithiophosphinic acid and tri-n-octyl phosphine oxide, tests were performed on extraction, lanthanide scrubbing and stripping. In the extraction test, up to 99.99% americium could be extracted from 0.5 kmol/m³ HNO₃, with approximately one third of the lanthanides being co-extracted. Mass transfer calculations using a consistent set of input data showed good agreement with the experiments.     

Synthesis of heterocyclic metal complexes and their evaluation as marine antifoulants

4-Amino-3-thio-1,24-triazolidine (L₁) and 4-amino-5-thio-1,3,4-thiadiazole (L_II) as well as their metal complexes of the general formulae ML_I·2H₂O and ML_IICl (M; Pb(II), Cd(II) and Zn(II)) were prepared. With Sn(II), we obtained Sn(L_I)₂·2H₂O and SnL_IICl, respectively. The structures of the compounds were identified through elemental analysis, and IR and UV spectra measurements, in addition to thermal analysis in case of the metal complexes. The antifouling properties of the compounds were tested by their incorporation into paint formulations which were applied to PVC substrates and tested in water from Alexandria western harbour. When the compounds were added at 17·5% by volume, the coated panels were fouled after 3 months of immersion. The addition of 6·7% by volume of tributyltin oxide to 15·8% of the prepared compounds in one formulation elevated the paint efficiency and prevented fouling for 11 months. Paint containing solely tributyltin oxide at the same concentration was inactive against algae.     

Shallow Linear Action Graphs and their Embeddings

Action calculi, which generalise process calculi such as Petri nets, π-calculusand ambient calculus, have been presented in terms of action graphs. We here offer linear action graphs as a primitive basis for action calculi. This paper presents the category of embeddings of undirected linear action graphs without nesting, using a novel form of graphical reasoning which simplifies some otherwise complex manipulations in regular algebra. The results are adapted in a few lines to directed graphs. This work is part of a long-term search for a uniform behavioural theory for process calculi. Received October 2000 / Accepted in revised form April 2001     

Adiabatic couplers: design rules and optimization

Explicit analytic design rules are derived for both 3 dB and full adiabatic couplers. The design rules are in excellent agreement with numerical calculations using the beam propagation method (BPM). It is shown that the length scaling for 3 dB couplers compared to full couplers makes the former more difficult to design. The design for each case is optimized to obtain the upper limit of performance and a comparison is carried out between two different design geometries for both 3 dB and full adiabatic couplers     

Reactivity of steam in exhaust gas catalysis III. Steam and oxygen/steam conversions of propane on a Pd/Al2O3 catalyst

A 1% Pd catalyst (38% dispersion) was prepared by impregnating a γ-alumina with palladium acetylacetonate dissolved in acetone. The behaviour of this catalyst in oxidation and steam reforming (SR) of propane was investigated. Temperature-programmed reactions of C₃H₈ with O₂ or with O₂ + H₂O were carried out with different stoichiometric ratios S(S =[O₂]/5[C₃H₈]). The conversion profiles of C₃H₈ for the reaction carried out in substoichiometry of O₂ (S < 1) showed two discrete domains of conversion: oxidation at temperatures below 350°C and SR at temperatures above 350°C. The presence of steam in the inlet gases is not necessary for SR to occur: there is sufficient water produced in the oxidation to form H₂ and carbon oxides by this reaction. Contrary to what was observed with Pt, an apparent deactivation between 310 and 385°C could be observed with Pd in oxidation. This is due to a reduction of PdO_x into Pd⁰, which is much less active than the oxide in propane oxidation. Steam added to the reactants inhibits oxidation while it prevents the reduction of PdO_x into Pd⁰. Compared to Pt and to Rh, Pd has a higher thermal resistance: no deactivation occurred after treatment up to 700°C and limited deactivation after treatment up to 900°C, provided that the catalyst is maintained in an oxygen-rich atmosphere during the cooling.     

Analysis of thin walled structures using the boundary element method

In this article the direct boundary element formulations of stretching and bending plate problems are combined together to solve thin walled structures and other similar frames. The final system is obtained by assuming each individual plane structural element as a subregion. After the necessary transforms of these equations they can be combined together taking into account the displacement compatibility and equilibrium conditions.     

Measurement and prediction of pressure drop in two-phase flow

Experimental data for air–water two-phase co-current flow in two different pipe diameters were used to test the prediction of pressure drop by a number of existing theories and correlations. Several models are shown to be useful for prediction, particularly with the stratified regimes which have proved difficult to handle in the past. The model suggested by Olujic proved to be of particular value.     

Power engineering industry interaction at Clemson University

The authors present a successful model of industry/university cooperation in establishing a strong power system curriculum in both the graduate and undergraduate level. Numerous long-term and short-term research projects have been developed to satisfy the university mission and to tackle challenging problems facing the power industry. A unique structure for the Clemson University Electric Power Research Association (CUEPRA) has been established to promote electric power system research and to meet the need for a working communication link between the power industry and the academic community. The power industries involvements in the power program at Clemson University and the strategic improvements that have been accomplished in research and education are outlined