Long-term sensor measurements of lung deposited surface area of particulate matter emitted from local vehicular and residential wood combustion sources

Abstract

Lung deposited surface area (LDSA) is a relatively new metric that has been argued to be more accurate at predicting health effects from aerosol exposure. For typical atmospheric aerosol, the LDSA concentration depends mainly on the concentration of ultrafine particles (e.g. vehicular exhaust emissions and residential wood combustion) and therefore optical methods cannot be used to measure and quantify it. The objective of this study was to investigate and describe typical characteristics of LDSA under different urban environments and evaluate how a diffusion charging-based Pegasor AQ Urban sensor (Pegasor Ltd., Finland) can be used as an alternative to optical sensors when assessing local combustion emissions and respective LDSA concentrations. Long-term (12?months) sensor measurements of LDSA were carried out at three distinctly different measurement sites (four sensor nodes) in the Helsinki metropolitan area, Finland. The sites were affected mainly by vehicular exhaust emission (street canyon and urban background stations) and by residential wood combustion (two detached housing area stations). The results showed that the accuracy of the AQ Urban was good (R² = 0.90) for the measurement of LDSA when compared to differential mobility particle sizer. The mean concentrations of LDSA were more than twice as high at the street canyon (mean 22 µm² cm^?3) site when compared to the urban background site (mean 9.4 µm² cm^?3). In the detached housing area, the mean concentrations were 12 µm² cm^?3, and wood combustion typically caused high LDSA peaks in the evenings. High correlations and similar diurnal cycles were observed for the LDSA and black carbon at street canyon and urban background stations. The utilization of a small-scale sensor network (four nodes) showed that the cross-station variability in hourly LDSA concentrations was significant in every site, even within the same detached housing area (distance between the two sites ～670?m).     

Bio-derived fuels may ease the regeneration of diesel particulate traps

Particulate is the most problematic emission from diesel engines. To comply with environmental regulations, these engines are often equipped with particulate traps, which must be regenerated frequently for the sake of efficiency. The regeneration is commonly achieved by rising the temperature in the trap till the particulate self-ignites. However, this method implies energy losses and thermal shocks in the trap. Alternatively, catalysts and additives have been recently considered for reducing the ignition temperature of particulate, but these techniques suffer from poisoning and undesirable byproducts. The present experimental study shows that the ignition temperature of particulate from seed-derived oils (SO) and from blends of SO with diesel fuel oil (DO) can be lower than that of particulate from neat DO. If substantiated by more extensive studies, such finding could have noteworthy implications on the future of fuels and traps.     

Is the development of adenoma and carcinoma in proximal colon related to apolipoprotein E phenotype?

BACKGROUND & AIMS: Alterations in plasma lipoprotein levels and bile acid metabolism observed in patients with colorectal adenoma and carcinoma may reflect a genetic background predisposing to altered lipid metabolism and tumors. This study was designed to determine whether the polymorphism of apolipoprotein E, one of the key regulatory proteins in cholesterol metabolism, is associated with proximal or distal colonic neoplasia. METHODS: Apolipoprotein E phenotype was determined in 135 patients with colorectal adenoma, 122 patients with colorectal carcinoma, and 199 randomly selected control subjects. RESULTS: The frequency of the epsilon 4 allele of apolipoprotein E was low (0.075 and 0.073) in patients with proximal adenoma and those with carcinoma, respectively, compared with the control subjects (0.181) (P < 0.05). In patients with distal tumors, there was no alteration in epsilon 4 frequency. In all subjects with the epsilon 4 allele compared with subjects without epsilon 4, the odds ratio for proximal adenoma was 0.36 (95% confidence interval, 0.14-0.89), and the odds ratio for proximal carcinoma was 0.35 (95% confidence interval, 0.14-0.86). CONCLUSIONS: The data suggest that the epsilon 4 allele of apolipoprotein E provides protection from the development of adenoma and carcinoma of the proximal colon. These results support the theory that there are common susceptibility genes modulating the susceptibility to external carcinogenic factors.     

Iron Behavior in the Ozonation and Filtration of Groundwater

In Finnish groundwater, the main substances that require treatment are iron and manganese. In addition to this, groundwaters are soft and acidic. Iron removal is usually relatively effective by oxidizing dissolved iron into an insoluble form, either by aeration or chemical oxidization and removing the formed precipitate by sand filtration. Sometimes, if the untreated water contains high amounts of organic matter, problems may arise for iron removal. In Finland, it is quite common that groundwater contains high levels of both iron and natural organic matter, mainly as humic substances. The groundwater of the Kukkala intake plant in Liminka has been found to be problematic, due to its high level of natural organic matter. This research studied the removal of iron from this water by means of oxidation with ozone and filtration. While the oxidation of iron by ozone was rapid, the precipitate particles formed were small, and thus could not be removed by sand and anthracite filtration, and the iron residue in the treated water was more than 2 mgL^?1. And while the filtration was able to remove iron well without the feed of ozone, the iron residue in the treated water was only 0.30 mgL^?1. In this case, iron was led to the filter in a bivalent dissolved form. So, the result of iron removal was the best when the sand/anthracite filter functioned largely as an adsorption filter.     

Reaction engineering studies in a polytropic fixed-bed reactor over a highly active and selective catalyst for oxidative methane coupling

The oxidative coupling of methane (OCM) was carried out in a polytropic fixed-bed reactor applying a Zr/La/Sr catalyst developed by the Neste company. Over this catalyst the OCM reaction follows a complex reaction scheme which includes primary parallel reaction steps to CO, CO₂ and C₂H₆ and consecutive reactions of ethane to ethylene or CO_x. Yield of higher hydrocarbons C₂₊ obtained with this catalyst strongly depended on reaction conditions, i.e. low partial pressures of methane and oxygen obtained by diluting the feed gas with nitrogen and high reaction temperatures promoted C₂₊ selectivity and yield. The maximum yield amounted to 21.4% (20 Vol.-% CH₄, 9 Vol.-% O₂, 71 Vol.-% N₂, T = 860°C; X_CH4 = 41.8%, S = 52.5%). This result belongs to the highest yields reported in the open literature.     

A new failure criterion for the Gurson-Tvergaard dilational constitutive model

In the Gurson-Tvergaard model a failure criterion has to be used to signify the void coalescence. In the literature, a constant critical void volume fraction criterion has been widely used. However, it is questionable whether the critical void volume fraction is a material constant and, furthermore, it is also difficult in practice to determine the constant. By modifying Thomason's plastic limit-load model, a new failure criterion which is fully compatible with the Gurson-Tvergaard model, is presented in this study. In the present criterion, the void coalescence failure mechanism by internal necking has been considered and the material failure is a natural result of the development of dual constitutive, stable and unstable, responses. In practical application of the present criterion, no critical void volume fraction needs to be pre-determined either numerically or experimentally. Furthermore, according to the new criterion, the void volume fraction corresponding to void coalescence is not a material constant, rather a function of stress triaxiality. The predictions using the present criterion have been compared with the finite element results by Koplik and Needleman, and very good agreement is observed. The potential advantage of this criterion and other related issues are discussed.     

Normalising OLAP cubes for controlling sparsity

A poorly designed OLAP (on-line analytical processing) cube can have a size much larger than the volume of information, potentially leading to problems with performance and usability. We give a new normal form for OLAP cube design and synthesis and decomposition algorithms to produce normalised OLAP cube schemata. OLAP cube normalisation controls the structural sparsity resulting from inter-dimensional functional dependencies. We assume that functional dependencies are used to describe the constraints of the application universe of discourse. Our methods help the user to identify cube schemata with structural sparsity, and to change the design in order to obtain more economy of space.     

A Microprocessor Controlled System For Photoelectrochemical Measurements

ABSTRACT

An automatic system for measuring photocurrent of electrodes as a function of excitation wavelength and electrode potential is described. Applications to a chemically modified transparent Sn0₂ electrode and an oxide-covered tantalum electrode are shown.     

Optimisation model for integration of cooling and heating systems in large industrial plants

Large industrial plants have often hundreds of heating and cooling heat exchangers. A common situation is that cooling demands of the processes are satisfied without any deeper analysis of the overall impact of the cooling systems on the plant’s economy or the environment. If cooling water is available it is used as much as needed and then pumped back to the river, some degrees warmer.An optimisation model was developed for integration of cooling and heating systems to tackle the problem. An industrial cooling system is a complex energy system comprising different options of producing cooling, distribution pipelines for cold media and cooling storages. Integration of power generation and heating systems to the cooling systems was included in the model. An illustrative example is presented in the paper. 10 process streams with cooling demand and 10 streams with heating demand were chosen, situated at different locations at the plant site. The optimal matches between the streams were found together with the sizes of the heat exchangers and the demands of hot and cold utilities. The costs of pipelines and the pumping costs of the streams are included in the model. The model can be used in the design of greenfield and retrofit investments and in versatile what-if analyses of the plant design or operation.