Analysis of surface wave behavior in corrugated piezomagnetic layer resting on inhomogeneous half-space

This paper deals with propagation of Love type waves in a Piezomagnetic layer with corrugated boundaries overlying an inhomogeneous half-space. Inhomogeneity of elastic half-space is caused due to exponential variations in elastic parameters. Dispersion relations are obtained for magnetically open and short cases. Prominent effects of inhomogeneity, layer's width and corrugation on the phase velocity of considered wave are illustrated through graphs. Some particular cases are derived and exhibited through graphs. Also the influence of undulation parameter, elastic parameter, and piezomagnetic coefficient on phase velocity of considered wave has been marked separately. The present study finds its applications in designing and optimization of Love wave sensors and Seismic Acoustic Wave (SAW) devices. Findings may also be used for analytical study of wave propagation in piezomagnetic coupled structures.     

Evaluation of alternate power conversion unit designs for the GT-MHR

General Atomics in the USA and Experimental Design Bureau of Machine Building (OKBM) in the Russian Federation have jointly developed a nuclear power plant design, the gas turbine modular helium reactor (GT-MHR). There have been considerable improvements during the last 10 years, which resulted in a more effective, efficient and safe design. The existing design is based on a 600 MW(t) reactor cooled by helium at a pressure of about 7 MPa. The power conversion unit (PCU) uses reactor outlet helium with a temperature of 850 °C in a direct Brayton cycle to achieve the cycle efficiency of about 48%. The PCU consists of a gas turbine, a recuperator, a precooler, low-pressure and high-pressure compressors, an intercooler, and a generator. The turbomachine (TM) includes the turbine, compressors and generator mounted on a single vertical shaft. TM shaft rotation speed is 4400 rpm. The shaft of generator is connected to the turbine shaft by a flexible coupling. The required grid frequency of generated electricity is achieved by a converter. All PCU components are enclosed in a single vessel. TM uses radial and axial electromagnetic bearings (EMB) for support. Catcher bearings (CB) are provided as redundant support for the TM rotor in case of EMBs failure. Several alternative PCU designs were analyzed on the basis of current progress in technologies, new world experience, and experience accumulated in the process of GT-MHR design development. Results of these analyses will be taken into account when a final PCU design is selected.     

Preparation,characterization, and in vivo evaluation of nano formulations of ferulic acid in diabetic wound healing

Diabetes mellitus is most common disorder characterize by hyperglycemia. Chronic hyperglycemia may lead to over production of free radicals thereby results in oxidative stress which impaired healing of wounds. Ferulic acid (FA) has been shown to have antidiabetic and antioxidant properties. The aim of the present study was to develop Ferulic acid nanoparticles and to study its hypoglycemic and wound healing activities. Ferulic acid-poly(lactic-co-glycolic acid) (FA-PLGA) nanoparticles were prepared by nano precipitation method. The prepared FA-PLGA nanoparticles had an average size of 240?nm. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) analysis showed the prepared FA-PLGA nanoparticles were spherical in shape. Drug encapsulation assay showed that 88.49% FA was encapsulated in PLGA. Carbopol 980 was used to formulate FA-PLGA nanoparticles loaded hydrogel. FA-loaded polymeric nanoparticles dispersion (oral administration) and FA-loaded polymeric nanoparticles based hydrogel (topical administration) treated wounds were found to epithelize faster as compared with diabetic wound control group. The hydroxyproline content increased significantly when compared with diabetic wound control. Therefore, the results indicate that FA significantly promotes wound healing in diabetic rats.     

预冷循环粗氩泵时突发故障的分析

在准备切换6000 m3/h空分设备制氩系统循环粗氩泵时,由于预冷阀和进液阀开度过大,使运行泵发生汽蚀,运行效率降低,导致主塔工况波动。简介制氩系统的流程和主要技术参数,介绍故障发生时相关运行参数的变化情况和处理措施,阐述相应的防范措施。     

Characterization and frictional behavior of nanostructured Ni–W–MoS2 composite coatings

Ni–W–MoS₂ composite coatings were obtained by pulse plating from a Ni–W electrolyte containing suspended MoS₂ particles. The coating composition, morphology, crystalline structure, microhardness and frictional behavior were studied as a function of MoS₂ concentration. The results obtained in this study indicate that co-deposited lubricant particles strongly influenced the composite Ni–W coating properties. It was found that increasing co-deposited MoS₂ diminished tungsten content in the coating and consequently increased the average grain size. Ni–W nanostructured coatings with high MoS₂ content have a porous sponge-like structure, high surface roughness and irregular frictional behavior. However, the friction coefficient of Ni–W coatings is reduced to half its value with low MoS₂ content.     

Use of discriminant analysis to predict arson-prone structures

Summary The technique of discriminant analysis is widely used for discriminating arson from nonarson structures. Since in this particular case only two groups are involved viz., the arson and the match groups, the computations required for obtaining a discriminant function are relatively simple. Because of this, it is possible to delete a variable by examining the value of a _i d _i where a _i is the coefficient for the i ^th variable in the discriminant function and d _i is the difference between the means for the arson and the match groups for the i ^th variable (i=1, 2, …, p). Thus, if a _i d _i <0 then we delete the i ^th variable from consideration because inclusion of such a varable, increases the probability of misclassification. A prior knowledge of a _i d _i is particularly useful when we have large numbers of variables to be considered. This will help to reduce the number of discriminant functions one needs to consider in order to arrive at the discriminant function which minimizes the misclassification probability. Frequently, in developing a discriminant function one strives to increase the probability of correct classification. However, this probability reflects two components, viz., the probability of correct classification of known arson structures and the probability of correct classification of known nonarson structures. Even if the overall probability of correct classification is high, it does not necessarily imply, as the illustrations of Boston and New York City indicate, that the resulting discriminant function is also efficient in the sense that more arson cases are correctly classified than the nonarson cases. To this end, a procedure has been suggested to compute the cost of the wrong decision for a discriminant function which can be used to compare the cost of two similar types of discriminant functions. Using the relative cost efficiency criterion, it has been shown that the discriminant function for Newark is more efficient than the discriminant function for either Boston or New York City. Reference: Shiledar Baxi, H., “Use of Discriminant Analysis to Predict Arson-Prone Structures,” Fire Technology, Vol. 20, No. 4, November 1984, p. 17