Generation of gas bubbles in microflow using micropipette with ultrasound

Ultrasound was applied to a micropipette micromixer to improve dispersion of gas and liquid in a microchannel. Flow visualization using a high-speed camera was performed to examine the effect of ultrasonic irradiation on bubble generation in the microchannel. Basically, nitrogen gas was injected using a (0.5 µm ID) glass micropipette into ethanol flowing in a rectangular (100 µm×200 µm) microchannel on polydimethylsiloxane (PDMS). Gas and liquid flow rates were regulated using mass flow controllers. At aflow condition that is typical of bubbly flow, ultrasound was transmitted into the microchannel using a piezo-electric (PZT) transducer over a range of operating voltages (2 to 200 Vp-p) and frequencies (50 to 60 kHz). Images captured during the action of the PZT transducer indicate that bubble formation is influenced by ultrasound. When subjected to ultrasound above 50 Vp-p and at the resonant frequency of the PZT transducer, bubbles formed that were smaller and closer together, signifying enhanced shearing of the gas at the micropipette tip by the liquid. The observation of gas slugs occurring sooner might be attributed to the coalescence of gas bubbles that became closely spaced.     

Strength of Al-Zn-Mg-Cu matrix composite reinforced with SiC particles

The AA7075 alloys reinforced with SiC and without SiC particles were fabricated by a pressureless infiltration method, and then, their tensile properties and microstructures were analyzed. The spontaneous infiltration of molten metal at 800 °C for 1 hour under a nitrogen atmosphere made it possible to fabricate 7075 Al matrix composite reinforced with SiC, as well as a control 7075 Al without SiC. A significant strengthening even in the control alloy occurred due to the formation of in-situ AlN particle even without an addition of SiC particles. Composite reinforced with SiC particles exhibited higher strength values than the control alloy in all aging conditions (underaged (UA), peak-aged (PA), and overaged (OA)), as well as a solution treated condition. Spontaneous infiltration was further prompted owing to the combined effect of both Mg and Zn. This may lead to an enhancement of wetting between the molten alloy and the reinforcement. Consequently, strength improvement in a composite may be attributed to good bond strength via enhancement of wetting. The grain size of the control alloy is greatly decreased to about 2.5 μm compared to 10 μm for the commercial alloy. In addition, the grain size in the composite is further decreased to about 2 μm. These grain refinements contributed to strengthening of the control alloy and the composite.     

Synthesis and surface properties of novel fluoroalkyl end-capped amphiphilic fullerene cooligomers

New fluoroalkyl end-capped fullerene cooligomers were prepared by the reactions of fluoroalkanoyl peroxides with fullerene and comonomers such as acryloylmorpholine, N,N-dimethylacrylamide and acrylic acid. These fluorinated fullerene cooligomers were easily soluble in water and common organic solvents, and were able to reduce the surface tensions of both water and benzene, quite effectively. Additionally, these fullerene cooligomers were found to form a stable monomolecular film at the air-water interface, and the modified polystyrene surface treated with these cooligomers was shown to have a strong hydrophilicity with good oil repellency.     

S06 桂花幻想之月夜——梦天

作为厦门园博会风景园林师园之一,本园以"梦天"为主题,结合东端开阔的水面条件,以月、桂、石为材,以天气的变化、月亮的位置、植物的变化、庭园本身的变化为主轴进行设计,使其成为一座可持续的庭园.     

High-performance carbon counter electrode for dye-sensitized solar cells

Here, we reported that a new carbon electrode prepared with an activated carbon was superior to a Pt sputtered electrode as the counter electrode of dye-sensitized solar cells. The photovoltaic performance was largely influenced by the roughness factor of carbon electrode. The open-circuit voltage increased by about 60 mV using the carbon counter electrode compared to the Pt counter electrode because of positive shift of the formal potential for I₃⁻/I⁻ couple.     

Mechanisms responsible for resistance of sublines derived from leukemia cell lines to an antitumor agent 9-beta-D-arabinofuranosyl-2-fluoroadenine

An agent 9-beta-D-arabinofuranosyl-2-fluoroadenine (2-F-Ara-A) is a main metabolite of fludarabine, a fluorinated purine analogue with antitumor activity in lymphoproliferative malignancies. In this study, the mechanism responsible for the resistance of cancer cells to fludarabine was examined using the 2-F-Ara-A-resistant sublines JOK-1/F-Ara-A and L1210/F-Ara-A from a human hairy leukemic cell line (JOK-1) and a mouse leukemic cell line (L1210) respectively, which were established by continuous treatment of the parental cell lines with 2-F-AraA. JOK-1/F-Ara-A and L1210/F-Ara-A cells were more than 55 and 29 times more resistant to 2-F-Ara-A than were their parent cell lines, and showed a high cross-resistance to 1-beta-D-arabinofuranosylcytosine but not to doxorubicin or vincristine. These resistant sublines intracellularly accumulated almost the same amount of 2-F-Ara-A as did their parent cell lines. However, the amount of 2-F-Ara-ATP, a cytotoxic metabolite of 2-F-Ara-A, decreased by 2.6% (JOK-1/F-Ara-A C3), 6% (L1210/F-Ara-A C1) and 3.7% (L1210/F-Ara-A C7) relative to the levels in the parent cell lines. Enzymatically, these resistant cells hardly activated deoxycytidine (dCyd) and 2-F-Ara-A. In addition, the abilities to phosphorylate deoxyadenosine and deoxyguanosine were also decreased in the resistant cells in comparison with the parent cells. These findings suggest that the deficiency in activity of dCyd kinase may contribute to the resistance of 2-F-Ara-A.     

Path planning for an autonomous mobile robot considering a region with a velocity constraint in a real environment

Recently, many research projects and competitions have attempted to find an autonomous mobile robot that can drive in the real world. In this article, we consider a path-planning method for an autonomous mobile robot that would be safe in a real environment. In such a case, it is very important for the robot to be able to identify its own position and orientation in real time. Therefore, we applied a localization method based on a particle filter. Moreover, in order to improve the safety of such autonomous locomotion, we improved the path-planning algorithm and the generation of the trajectory so that it can consider a region with a limited maximum velocity. In order to demonstrate the validity of the proposed method, we participated in the Real World Robot Challenge 2010. The experimental results are given.     

Catching a molecule at the air-water interface: Dynamic pore array for molecular recognition

As a soft and flexible porous structure, a pore array of a steroid cyclophane SC(OH), which consists of the rigid 1,6,20,25-tetraaza[6.1.6.1]paracyclophane ring connected to four steroid moieties (cholic acid) through flexible L-lysine spacers, was prepared at the air-water interface. As confirmed by surface pressure (π)-molecular area (A) isotherms, transition between open conformation and cavity conformation of the SC(OH) molecule was reversibly induced upon repeated compression and expansion of its monolayer at pH 11 where amino groups of the lysine residues are not fully deprotonated. Capture and release of an aqueous fluorescent guest (TNS) by SC(OH) was observed upon dynamic cavity formation through surface fluorescence spectroscopy. At pH 12, dynamic cavity formation of SC(OH) was sufficiently suppressed, and the capture and release of an aqueous TNS by the monolayer was not virtually observed. Lessened electrostatic repulsion between the SC(OH) molecules due to conversion of ammonium to free amine may prevent the cavity from reopening. The importance of dynamic nature of cavity formation on the guest binding was also proved by control experiments using SC(H), which cannot form cavity conformation at any surface pressures at both pH 11 and 12.