Multi-dimensional transient mathematical simulator of blast furnace process based on multi-fluid and kinetic theories

The ironmaking blast furnace is regarded as one of the biggest and most complex industrial reactors, because it includes various materials like gas, lump granular materials, liquids and powders and more than 30 major reactions and phase changes in a single reaction vessel. The mathematical simulator of this process developed in this study used the multi-fluid treatment as its framework, since the motions of these materials were governed by different flow mechanisms. The rates of the interactions among the phases and the chemical reactions were evaluated based on kinetic theories. The model successfully reproduced the fields of velocity, temperature and reaction in the furnace and its validity was confirmed. The simulator was also applied to a novel operation, namely the top gas recycling combined with the carbon-composite iron-ore charging and the waste plastics injection, and the advantages in furnace efficiency and environmental load were quantitatively indicated.     

Free energy perturbation study on a Trp-binding mutant (Ser88 ->Cys) of the trp-repressor

The Ser⁸⁸Cys mutant of the trp-repressor showed a lower affinityfor the corepressor than the wild-type repressor [G = 1.7 ±0.3 kcal/mol, Chou and Matthews (1989) J. Biol. Chem., 264,18314–18319].A molecular dynamics/free energy cycle perturbation study wasperformed to understand the origin of the decreased affinity.A value (G = 1.58 ± 0.28 kcal/mol) comparable with theexperimental value was obtained by the simulation. Free energycomponent analysis revealed that destabilization of the vander Waals interaction between Ser⁸⁸ and Trp¹⁰⁹ (corepressor)mainly contributed to the decreased affinity of the mutant.The rotational transition of the hydroxyl (sulfhydryl) groupof Ser⁸⁸ (Cys⁸⁸) during the simulations affected the contributionsof Arg⁸⁴ and water to the free energy change in the aporepressorand those of Arg⁸⁴ and Trp ¹⁰⁹ to that in the holorepressor.However, the contributions from different residues compensatedeach other, and the total free energy changes were almost invariablein the various simulations.     

Fault tolerant approach for biosignal-based robot control

This paper proposes a fault tolerant framework for biosignal-based robot control with multiple sensor electrodes. In this approach, to cope with sensor faults, a reliable joint torque estimation model is selected from a group of estimation models based on sensor failure classifiers. The correlation among the electromyography (EMG) signal streams is used as input feature vectors for fault detection. To validate our proposed method, we artificially disconnect an EMG electrode or detach one side of an EMG probe from the skin surface during elbow-joint torque estimation experiments with five participants. When one EMG sensor electrode experiences one of the problems, the experimental results show that the joint torque can be estimated with significantly fewer errors using our proposed approach than a joint torque estimation method without sensor fault detection or than a method with a conventional sensor fault detection algorithm. Furthermore, we controlled a mannequin-arm-attached one-DOF exoskeleton based on the estimated torque profiles by generating movements with the estimated torque derived from the selected model.     

Numerical Simulation of Innovative Operation of Blast Furnace Based on Multi-Fluid Model

To date ,blast furnace operators have a relative-ly good understanding of internal mechanisms ,andno longer treat blast furnace as a“black box”. Forthe blast furnace , however , one of the most com-plex metallurgical units inthe field of chemical engi-neering,the complexity keeps proliferating with theadoption of newtechnologies ,such as high rate in-jection of pulverized coal ,effective use of carbona-ceous andferrous materials ,and so on.If merely bydirect instrumentation and empirical kno…     

The preattentive emperor has no clothes: A dynamic redressing.

Preattentive models of early vision have not been supported by the evidence. Instead, an input filtering system, which is dynamically reconfigured so as to optimize performance on the task at hand, is proposed. As a case in point, the authors examined Sagi and Julesz's (1985a) claim that detection tasks are processed preattentively and efficiently (shallow search slopes), whereas discrimination tasks require focal attention and yield inefficient steep slopes. In 5 visual search experiments, efficiency was found to depend not on the nature of the task but on whether the task is single or dual. The second component of a dual task, whether detection or discrimination, is performed inefficiently if it does not fit the configuration of the input system, which had been set optimally for the first component. But, even the second component is processed efficiently if there is enough time to reconfigure the system after processing the first component. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Needle penetrometry with variable force loading for measuring viscosity of pelletized coal upon heating

A needle penetrometry was performed loading steady force in a range from 1×10⁻³ to 2 N to pelletized coal upon heating via a cylindrical needle. From the observed effects of shear rate on apparent viscosity of softening coal pellet, defined as the shear-rate to shear-stress ratio, it was found that the pellet behaved as a Newtonian fluid for shear rates lower than a critical one while as a pseudo-plastic fluid for higher shear rates. The penetrometry was also carried out varying the force with time. The variable force loading enabled to maintain the shear rate well below the critical one, and thereby to measure the apparent viscosity of coal pellets as Newtonian fluids over a temperature range from 600 to 800 K. Upon heating at 10 K min⁻¹, the apparent viscosity of Goonyella coal pellet decreased from about 10¹⁰ Pa s at 640 K down to a minimum of about 10⁴ Pa s at 755 K, and increased up to 10⁹ Pa s at 800 K. In a course of heating as above, the viscosity of Blind Canyon coal pellet decreased above 600 K, underwent a minimum of about 10⁶ Pa s at 715 K, and increased up to 10¹⁰ Pa s at 770 K. Decreasing the heating rate from 10 to 3 K min⁻¹ caused the minimum viscosities of the pellets to increase by 1-2 orders of magnitude.     

Difference in environmental degradability between poly(ethylene succinate) and poly(3-hydroxybutyrate)

A chemosynthetic aliphatic polyester, poly(ethylene succinate) (PESu), was degraded by a poly(3-hydroxybutyrate) (P(3HB)) depolymerase in vitro. While P(3HB) exhibited good biodegradability in all environments, PESu hardly underwent biodegradation in a marine environment. To understand the difference in environmental degradability between PESu and P(3HB), we investigated the distribution of P(3HB)- and PESu-degrading microbes in various environments. PESu-degrading microbes were never detected in marine environments. PESu-degrading bacteria isolated from various environments in this study belonged to the phyla Firmicutes and Proteobacteria. Most PESu-degrading bacterial isolates could not degrade P(3HB), suggesting that PESu was not degraded by P(3HB) depolymerase in actual environments. In addition, all bacterial isolates that were screened for P(3HB) degrading activity from various environments in this study did not degrade PESu, suggesting that PESu does not induce P(3HB) depolymerase in their bacteria and P(3HB)-degrading bacteria are not involved in biodegradation of PESu in actual environments. Taken together, these results could be related with the low biodegradability of PESu in marine environments.     

Carboxylated polysulfone membranes having a chiral recognition site induced by an alternative molecular imprinting technique

SUMMARY Molecularly imprinted polymeric membranes were prepared from carboxylated polysulfone. Membranes imprinted by Z-D-Glu recognize the D-isomer in preference to the corresponding L-isomer, and vice versa. The amino acid preferentially adsorbed by the membrane was also selectively permeated by electrodialysis. Received: 22 January 1998/Accepted: 20 February 1998     

Attentional requirements in visual detection and identification: Evidence from the attentional blink.

Perception of the 2nd of 2 targets (T1 and T2) is impaired if the lag between them is short (0–500 ms). The authors used this attentional blink (AB) to index attentional requirements in detection and identification tasks, with or without backward masking of T2, in 2 stimulus domains (line orientation, coherent motion). With masking, the AB occurred because T2 was masked during the attentional dwell time created by T1 processing (Experiments 1, 2, and 3). Without masking, an AB occurred only in identification because during the attentional dwell time. T2 decayed to a level that could support simple detection but not complex identification. However, an AB occurred also in detection if T2 was sufficiently degraded (Experiment 4). The authors drew 2 major conclusions: (a) Attention is required in both identification and detection, and (b) 2 factors contribute to the AB, masking of T2 while attention is focused on T1 and decay of the T2 trace while unattended. (PsycINFO Database Record (c) 2010 APA, all rights reserved)