Fundamental Evaluation of Power Supply and Rectifiers for Wireless Power Transfer Using Magnetic Resonant Coupling

This paper provides a fundamental analysis of a power supply and rectifiers for wireless power transfer using magnetic resonant coupling (MRC). MRC enables efficient wireless power transfer over middle‐range transfer distances. MRC for wireless power transfer should operate at a high frequency in the industry science medical band, such as 13.56 MHz, because the size of the transfer device decreases at higher transfer frequencies. Therefore, the output frequency of the power supply on the transmitting side should be 13.56 MHz. In addition, the rectifier on the receiving side is operated at a high frequency. This paper focuses on the reflected power in the power supply and rectifiers. Thus, the parametric design method is clarified for the power supply, including a low‐pass filter to match the output, the impedance of the power supply with the characteristic impedance of the transmission line. In addition, the effects on the rectifiers of silicon carbide and gallium nitride diodes are confirmed by performing an experiment and a loss analysis.     

Studies on chitin. IX. Crosslinking of water-soluble chitin and evaluation of the products as adsorbents for cupric ion

Water-soluble chitin was successfully crosslinked to varying extents with glutaraldehyde in homogeneous aqueous solutions to improve the properties as an adsorbent for metal cations, and the effects of crosslinking were discussed. Complete insolubilization was achieved with the fivefold excess aldehyde, but, in terms of adsorptivity of Cu²⁺, the chitin crosslinked at an aldehyde/amino group ratio of 1.0 was found to exhibit remarkable capacity and was much superior to others. The desorption of Cu²⁺ from the adsorption complex was also attained effectively at pH 2.0. These results indicated that the loose crosslinking was quite simple and efficient to produce high capacity adsorbents for practical use. Thermal behavior of the crosslinked chitin was examined by TMA and TGA; a softening phenomenon was observed at 145°C.     

370 W output power GaN-FET amplifier for W-CDMA cellular base stations

A single-ended amplifier using small packaged GaN-FETs exhibits a record 2.14 GHz W-CDMA output power. The amplifier, composed of paralleled 48 mm gate periphery FET die, delivers a peak saturated output power of 371 W with a linear gain of 11.2 dB at a drain voltage of 45 V under 2.14 GHz 3GPP W-CDMA signal input. The output power density (output power/package size) of 1.1 W/mm/sup 2/ is twice as high as that of the existing over 300 W GaAs-FET amplifiers. A low 5 MHz offset ACLR of -36 dBc with a drain efficiency of 24% is also obtained at 8 dB power back off from the saturated output power.     

Mechanical alloying in the Al-Bi alloy system

Mechanical alloying (MA) was carried out to investigate the MA behaviour of the immiscible Al-10, 30 at % Bi alloys. After the MA processing, the Al and Bi were finely and homogeneously alloyed. The Bi crystallite size decreased to 25 nm and 30 nm in the Al-10 at % Bi and Al-30 at % Bi alloys, respectively. By increasing the MA time, the hardness increased up to a value of 80 H _v, which is larger than that obtained from the rule of mixtures. The lattice parameter of Bi decreased by about 0.27%, which shows the formation of a non-equilibrium hcp Bi super-saturated solid solution. The extended solubility of Al in Bi was 1.9% in the Al-30 at % Bi alloy. Due to the extended solubility, depression of the melting temperature of hcp Bi was confirmed in the mechanically alloyed Al-Bi alloys. The maximum depression in the temperature was about 10 K. The measured values corresponded well with those estimated from the extrapolation of the solidus line.     

Immunoassay method for the determination of immunoglobulin G using bacterial magnetic particles.

We have developed a novel immunoassay method using bacterial magnetic particles for the determination of immunoglobulin G (IgG). Fluorescein isothiocyanate (FITC) conjugated anti IgG-bacterial magnetic particles were prepared. The fluorescence quenching caused by agglutination of FITC-anti IgG antibody-bacterial magnetic particle conjugates was measured by using a fluorescence spectrophotometer. The aggregates based on specific immunoreaction were separated by a gelatin solution. The aggregation of bacterial magnetic particle conjugates was enhanced by application of a magnetic field. The relative fluorescence intensity correlated linearly with a concentration of IgG in the range 0.5-100 ng/mL.     

Recovery retardation in equal channel angular pressed Al–Zr alloy during friction stir welding

The effect of Zr on reduction of hardness and microstructure in an FS weld of equal channel angular-pressed Al alloy was investigated. Zr addition to Al suppressed dynamic recovery in the thermomechanically affected zone and enabled retention of the high hardness of the ECA-pressed material throughout the weld.     

Successful eradication of H. pylori in an elderly patient with gastric cancer after effective UFT-E therapy

The patient was a 83-year-old female with 2' T2-type gastric cancer associated with positive H. pylori in the lesser curvature of the stomach. The patient was treated with oral UFT-E alone in a daily dose of 400 mg. The tumor exhibited an O' IIa + IIc-like appearance 4 weeks after the start of administration and became scarred 8 weeks later, revealing marked tumor reduction in a short period of time. At 8 weeks, biopsy showed marked polymorphonuclear cells infiltration of gastric mucosa with no evidence of malignancy. In an attempt to eradicate H. pylori, 30 mg of lansoprazole, 400 mg of clarithromycin, and 2.0 g of ecabet-Na (3.0 g of Gastrom) were administered for 2 weeks. H. pylori was found to have been successfully eradicated, and the inflammatory lesions were no longer visible histologically. UFT-E was highly effective in this patient, and the eradication of H. pylori may contribute to the prevention of cancer recurrence.     

The first specific antibody against cytotoxic polyacetylenic alcohol, panaxynol

Antitumor polyacetylenic alcohol, panaxynol, was isolated and purified from a powder of the root of Panax ginseng C.A. Meyer. Panaxynol inhibited the growth of various kinds of cultured tumor cell lines in a dose-dependent manner. In this paper we demonstrated the first specific antibody production against panaxynol. Anti-panaxynol antibody was elicited in rabbits by immunization with panaxynol hemisuccinate-bovine serum albumin conjugate (panaxynol hemisuccinate-BSA conjugate). An enzyme immunoassay (EIA) for the determination of panaxynol was established using a double-antibody technique. The EIA was highly specific against panaxynol although the antibody showed a minimal cross-reactivity with other types of polyacetylenic alcohol, i.e. panaxydol (12.0%) and panaxytriol (0.77%). Panaxynol at a concentration as low as 6.4 ng/ml can be detected. Using this assay we reconfirmed the rapid consumption of panaxynol by target tumor cells in an in vitro-culture system. The anti-panaxynol antibody may be a valuable tool for studies of the biological properties of polyacetylenic compounds.     

Antiproliferative constituents in umbelliferae plants. IV. Constituents in the fruits of Anthriscus sylvestris Hoffm

The constituents in the fruit of Anthriscus sylvestris Hoffm. were investigated, and four lignans [deoxypodophyllotoxin, morelensin, (-)-deoxypodorhizone, and (-)-hinokinin], one phenylpropanoid [1-(3',4'-dimethoxyphenyl)-1 xi-hydroxy-2-propene], two phenylpropanoid esters [3',4'-dimethoxycinnamyl (Z)-2-angeloyloxymethyl-2-butenoate and 3',4'-dimethoxycinnamyl (Z)-2-tigloyloxymethyl-2-butenoate], and one polyacetylenic compound (falcarindiol) were isolated. Their antiproliferative activity against MK-1, HeLa and B16F10 cell lines is reported.     

A 20 GHz 8 bit multiplexer IC implemented with 0.5 μm WNx/W-gate GaAs MESFET's

An ultrahigh-speed 8 bit multiplexer (MUX) has been developed for future-generation optical-fiber communication systems having a data rate of 20 Gb/s. This IC was fabricated using a 0.5 μm WN_x/W-gate GaAs MESFET process based on optical lithography, ion implantation, and furnace annealing for good reproducibility and high throughput. The WN_x/W bilayer gate has a low sheet resistance, improving the circuit high frequency performance. To attain 20 GHz operation, advanced circuit techniques for the source-coupled FET logic (SCFL) were introduced. A cross coupled source-follower (CCSF) was developed mainly for the highest speed buffers to enhance the bandwidth. The first-stage T-type flip-flop was designed with optimization techniques and operated up to 21.1 GHz