Aripiprazole as a potential pharmacotherapy for stimulant dependence: Human laboratory studies with d-amphetamine.

Amphetamine and cocaine dependence present significant public health concerns, yet no broadly effective pharmacotherapy for stimulant dependence has been developed. Two human laboratory studies are reviewed that tested the ability of aripiprazole, a novel antipsychotic with partial agonist activity at D2 dopamine receptors, to alter the behavioral effects of stimulants using d-amphetamine as a model agent. In each of these experiments, volunteers learned to discriminate 15 mg d-amphetamine (i.e., ≥80% drug-appropriate responding over 4 consecutive sessions). The effects of a range of doses of d-amphetamine (0, 2.5, 5, 10, and 15 mg) were then tested alone and following pretreatment with aripiprazole (20 mg in Experiment 1; 10 mg in Experiment 2). In Experiment 1, aripiprazole (20 mg) attenuated the discriminative stimulus and many of the subject-rated effects of amphetamine. Aripiprazole alone produced performance decrements. To determine whether a lower dose of aripiprazole would also attenuate the behavioral effects of d-amphetamine without impairing performance, Experiment 2 was conducted. Aripiprazole (10 mg) failed to alter the discriminative-stimulus effects but attenuated some of the subject-rated effects of d-amphetamine. This dose of aripiprazole did not impair performance. The results of these experiments indicate that aripiprazole may have clinical utility in treating stimulant dependence. Future human laboratory research should better model the clinical use of aripiprazole by examining the effects of chronic aripiprazole combined with either methamphetamine or cocaine in dependent individuals. A large-scale clinical trial is also needed to evaluate the efficacy of aripiprazole for the treatment of stimulant dependence. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Recovery of gold cyanide using inherently conducting polymers

Removal of gold from basic solutions containing [Au(CN)₂]^? has been demonstrated using the inherently conducting polymer polypyrrole. Polymers containing sulfonated aromatic dopants have been found to display a significant ability to remove gold from such solutions. Experiments performed in solutions containing both gold and copper cyanide complexes indicate that the recovery process is not highly selective. However, the polypyrroles used display significantly faster rates of gold recovery than activated carbon. © 2003 Society of Chemical Industry     

Scanning Acoustic Microscopy of SCS-6 Silicon Carbide Fiber

Scanning acoustic microscopy of SCS-6 silicon carbide fiber reveals large radial variations in acoustic reflectivity associated with the chemical composition and microstructure of a given fiber region. Rayleigh wave fringe patterns observed in each of five subregions are used to calculate the average Young modulus of that subregion. The Young modulus is found to increase monotonically from 40 GPa in the carbon core to a value of 413 GPa in the stoichiometric SiC region. The effective Young modulus of the fiber as a whole is estimated from the moduli of the individual regions and it is compared with mechanical measurements reported in the literature.     

REENGINEERING DONE RIGHT Intermediate Solutions That Are Cost-Effective

Effective systems development techniques attract a lot of attention, but little has been done to effectively address systems maintenance. This article describes an effective, proven approach to resurrecting existing systems and Increasing their useful life, using a system that employs both software tools and a rigorous methodology.     

Overview and update.

A summary of points of agreement and disagreement among the preceding articles is presented. Attention is called to implicit assumptions which if openly acknowledged would improve dialogue on peer review issues. Pertinent events that have occurred since the Anaheim symposium are reviewed. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

The effects of pressure on the isothermal fluid behavior of bituminous coals

An investigation into the effects of pressure (helium gas) on the isothermal fluid behavior includes: (1) the effect of pressure on the rate of melting and coking as evidenced by the rate constants k(melt) and k(coke); (2) the effect of pressure on the energies of activation of melting and coking; (3) the effects of pressure on the characteristic times; (4) the effects of pressure on the maximum isothermal fluidity. Results from the effects of pressure on k(melt) revealed that it was generally the high total sulfur, low nitrogen, low reactives/mineral matter ratio, medium rank coals which show the greatest increase in k(melt), whereas the highest rank coals show the least decrease in k(coke). The energies of activation of melting and coking were not significantly affected by pressure. The investigation also reveals increases or decreases in the respective times of softening, maximum fluidity, resolidification and total time of fluid behavior under isothermal pressurized conditions. There appears the possibility that these shifts may be rank dependent. Additionally, the lower rank coals show the largest relative increase in their fluidities when subjected to pressure. Empirical relationships were derived in order to quantitatively predict the maximum isothermal fluidity for most (fluid) coals at a given pressure.     

A Built-in Self-Test Scheme with Diagnostics Support for Embedded SRAM

In this paper we propose a novel built-in self-test (BIST) design for embedded SRAM cores. Our contribution includes a compact and efficient BIST circuit with diagnosis support and an automatic diagnostic system. The diagnosis module of our BIST circuit can capture the error syndromes as well as fault locations for the purposes of repair and fault/failure analysis. In addition, our design provides programmability for custom March algorithms with lower hardware cost. The combination of the on-line programming mode and diagnostic system dramatically reduces the effort in design debugging and yield enhancement. We have designed and implemented test chips with our BIST design. Experimental results show that the area overhead of the proposed BIST design is only 2.4% for a 128 KB SRAM, and 0.65% for a 2 MB one.