Influence of third monomer on the crystal phase transition behavior of ethylene-tetrafluoroethylene copolymer

Crystal phase transition between the low- and high-temperature phases has been investigated for ethylene (E)-tetrafluoroethylene (TFE) alternating copolymer (ETFE) containing the third monomeric species by the temperature dependent measurements of wide-angle X-ray diffraction (WAXD) and small-angle X-ray scattering (SAXS) and differential scanning calorimetry. Nonafluoro-1-hexene (NFH) and hexafluoropropylene (HFP) were chosen as the third monomers, where they are different in the side-branch length, -(CF₂)₃CF₃ and -CF₃, respectively. In the case of E/TFE/NFH copolymer (ET-C4F9), the crystal phase transition temperature of the original ETFE two-components copolymer was not very much affected by the existence of NFH in the range of NFH content from 0.7 to 3 mol%. Contrarily, the crystal phase transition temperature of E/TFE/HFP copolymer (ET-CF3) was found to decrease drastically with increasing HFP content. The melting temperature and the higher-order structure were also affected sensitively depending on the HFP content. This difference in phase transition behavior between ET-C4F9 and ET-CF3 copolymers is reasonably interpreted as follows: the short side groups (-CF₃) of HFP monomeric unit are included in the crystal lattice of E/TFE chains and the unit cell is expanded gradually with an increment of the HFP content, resulting in the decrease in phase transition point because of easier thermal motion of the chains. On the other hand, the long side groups [-(CF₂)₃CF₃] of NFH monomeric units are excluded out of the crystal lattice and located on the lamellar surfaces or in the amorphous region and do not affect very much the phase transition temperature even when the NFH content is increased. In association with such a change in crystal structure, the long period of stacked lamellar structure was found to decrease remarkably in the case of NFH, whereas it does not change very much for HFP, consistent with the interpretation of the above-mentioned WAXD data.     

Preparation and properties of polyimide/silica hybrid composites based on polymer‐modified colloidal silica

A new type of polyimide/silica (PI/SiO₂) hybrid composite films was prepared by blending polymer‐modified colloidal silica with the semiflexible polyimide. Polyimide was solution‐imidized at higher temperature than the glass transition temperature (T_g) using 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA) and 4,4′‐diaminodiphenyl ether (ODA). The morphological observation on the prepared hybrid films by scanning electron microscopy (SEM) pointed to the existence of miscible organic–inorganic phase, which resulted in improved mechanical properties compared with pure PI. The incorporation of the silica structures in the PI matrix also increased both T_g and thermal stability of the resulting films. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2053–2061, 2006     

Antioxidizing component,musizin, inrumex japonicus houtt

A substance with antioxidant properties was obtained from the hexane extract of roots ofRumex japonicus Houtt. The active component of the hexane extract was isolated and characterized as 2-acetyl-1,8-dihydroxy-3-methyl naphthalene, trivially named musizin (MUS). The antioxidant activities of MUS in six types of fats and oils were higher than that of butyl hydroxyanisole (BHA) and δ-tocopherol (δ-TOC). Together, TOC and MUS have a synergistic effect, because comparable amounts of either had lower antioxidant activity than various combinations of the two antioxidants. When we studied the antioxidant properties of a mixture of MUS and δ-TOC with methyl linoleate (MeLH), we found that the rates of destruction of the two antioxidants were comparable, but that their destruction occurred sequentially, with MUS first followed by δ-TOC, after which the oxidation of MeLH quickly occurred. Comparison of the antioxidant activity of MUS and its analogs suggests that only one of the two hydroxyl groups in MUS is involved in its antioxidant activit. Intermolecular hydrogen bonding may be involved.     

The eta phases and mechanical properties of TIG welded joints of WC-Co cemented carbide and steel

The tungsten-inert-gas (TIG) arc welding experiments of cemented carbide YG30 and steel 45 were carried out using the Ni-Fe-C filling alloys. The eta phases and mechanical properties of welded joints were analyzed by means of scanning electronic microscope (SEM) , transmission electronic microscope (TEM) coupled with selected diffraction, electronic probe microanalysis and bending strength method. The experimental results show that the chemical composition of the filling alloys affects eta phase formation. When the carbon and nickel contents in filling alloys are O. 61 wt% and 55. 29 wt% ,respectively, no eta phases form. And the joint bending strength is the highest to 1. 352 GPa. But if they are O. 01wt% and 55.38wt%, the eta phases are formed at the boundaries of the cemented carbide and the weld, and the thickness of eta phase layer is about 110 micrometers. And the joint bending strength is low. Usually, these eta phases are anomalously granular,and easy to accumulate at the boundaries between cemented carbides and the weld. They are multiple M6C rich in tungsten and iron.     

A new approach to the design of high-Tc superconductors: Metallised interlayers

We show from muon spin relaxation (SR) studies on mercury HTS superconductors that a 50-fold increase in irreversibility field obtained by partial substitution of Re for Hg is due to metallisation of the Hg/Re layer. Induced superconductivity on this metallic layer doubles the overall superfluid density. This suggests a new approach to the design of high performance HTS materials: metallising one of the non-CuO₂ interlayers and thereby greatly enhancing the superconducting properties.     

Experimental and numerical study on hydrodynamics of riparian vegetation

Recently, many channelized rivers tend to be heavily vegetated due to regime shifts in hydrological, fluvial and ecological processes. Dense vegetation in a river frequently obstructs a flood flow and reduces conveyance capacity of channels. On the other hand, river vegetation provides various ecological services such as habitats for various species and life, natural cycle of organic and inorganic substances, etc.. It is of engineering importance to understand vegetation hydrodynamics in order to preserve vegetation nature and keep a certain level of flow conveyance capacity. In view that willows tend to be densely vegetated along the shoreline of floodplains or sandbars, a field measurement, a physical model experiment and a numerical analysis were carried out for investigating hydrodynamics in an open channel with riparian vegetation. Discussion was made focusing on flow and shear layer structures developed around the vegetation canopy.     

Selective Patterning of Gold Surfaces by Core/Shell,Semisoft Hybrid Nanoparticles

The generation of patterned surfaces with well‐defined nano‐ and microdomains is demonstrated by attaching core/shell, semisoft nanoparticles with narrow size distribution to microdomains of a gold‐coated silicon wafer. Near monodisperse nanoparticles are prepared using reversible addition‐fragmentation chain transfer (RAFT) polymerization, initiated from a silica surface, to prepare a polystyrene shell around a silica core. The particles are then used as‐prepared, or after aminolysis of the terminal thiocarbonyl group of the polystyrene shell, to give thiol‐terminated nanoparticles. When gold‐coated silicon wafers are immersed into very dilute suspensions of these particles (as low as 0.004 wt%), both types of particles are shown to adhere to the gold domains. The thiolated particles adhere selectively to the gold microdomains, allowing for microdomain patterning, while particles that contain the trithiocarbonate functionality lead to a much more even coverage of the gold surface with fewer particle aggregations.     

Electronic Structures of Two-Phase Microstructures in Pb-doped Bi2Sr2CaCu2O y

We have performed scanning tunneling microscopy/spectroscopy (STM/STS) on single crystals of heavily Pb-doped Bi ₂ Sr ₂ CaCu ₂ O _y (Pb-Bi2212). The obtained STM images clearly demonstrated phase separation into the and phases with lamella-type and new zigzag-like microstructures. From the site-specified tunneling measurements, it was directly confirmed that the phase possesses higher T _c . This suggests that the phase boundaries act as strong pinning sites especially at higher temperatures.