Structural Aspects of P2-Type Na0.67Mn0.6Ni0.2Li0.2O2 (MNL) Stabilization by Lithium Defects as a Cathode Material for Sodium-Ion Batteries

A known strategy for improving the properties of layered oxide electrodes in sodium-ion batteries is the partial substitution of transition metals by Li. Herein, the role of Li as a defect and its impact on sodium storage in P2-Na_0.67Mn_0.6Ni_0.2Li_0.2O₂ is discussed. In tandem with electrochemical studies, the electronic and atomic structure are studied using solid-state NMR, operando XRD, and density functional theory (DFT). For the as-synthesized material, Li is located in comparable amounts within the sodium and the transition metal oxide (TMO) layers. Desodiation leads to a redistribution of Li ions within the crystal lattice. During charging, Li ions from the Na layer first migrate to the TMO layer before reversing their course at low Na contents. There is little change in the lattice parameters during charging/discharging, indicating stabilization of the P2 structure. This leads to a solid-solution type storage mechanism (sloping voltage profile) and hence excellent cycle life with a capacity of 110 mAh g^-1 after 100 cycles. In contrast, the Li-free compositions Na_0.67Mn_0.6Ni_0.4O₂ and Na_0.67Mn_0.8Ni_0.2O₂ show phase transitions and a stair-case voltage profile. The capacity is found to originate from mainly Ni³⁺/Ni⁴⁺ and O^2-/O^2-δ redox processes by DFT, although a small contribution from Mn⁴⁺/Mn⁵⁺ to the capacity cannot be excluded.     

In situ observation of synthesized nanoparticles in ultra-dilute aerosols via X-ray scattering

In-air epitaxy of nanostructures (Aerotaxy) has recently emerged as a viable route for fast, large-scale production. In this study, we use small-angle X-ray scattering to perform direct in-flight characterizations of the first step of this process, i.e., the engineered formation of Au and Pt aerosol nanoparticles by spark generation in a flow of N₂ gas. This represents a particular challenge for characterization because the particle density can be extremely low in controlled production. The particles produced are examined during production at operational pressures close to atmospheric conditions and exhibit a lognormal size distribution ranging from 5–100 nm. The Au and Pt particle production and detection are compared. We observe and characterize the nanoparticles at different stages of synthesis and extract the corresponding dominant physical properties, including the average particle diameter and sphericity, as influenced by particle sintering and the presence of aggregates. We observe highly sorted and sintered spherical Au nanoparticles at ultra-dilute concentrations (< 5 × 10⁵ particles/cm³) corresponding to a volume fraction below 3 × 10^–10, which is orders of magnitude below that of previously measured aerosols. We independently confirm an average particle radius of 25 nm via Guinier and Kratky plot analysis. Our study indicates that with high-intensity synchrotron beams and careful consideration of background removal, size and shape information can be obtained for extremely low particle concentrations with industrially relevant narrow size distributions.

     

Effects of breed and age at slaughter on degradation of muscle lipids during processing of dry‐cured hams

Hams from Landrace, Duroc and Hampshire pigs slaughtered at ages 6, 7.5 and 9 months were processed to generate Norwegian Parma‐style hams. Lipid contents and the compositions of fatty acid classes (ΣSFA, ΣMUFA, ΣPUFA) within neutral lipids, phospholipids and free fatty acids were determined. Small differences in lipid degradation and composition of the classes were revealed. However, significant sensory differences related to lipids were observed. Breed was more important than age. Dry‐cured Hampshire hams gave a more intense mature odour that may be associated with higher overall lipid degradation. Unexpectedly, these hams also demonstrated high juiciness and tenderness, which could be related to the melting characteristics of the fat. Dry‐cured Duroc hams showed a higher susceptibility towards rancidity, presumably associated with preferential oxidation of n‐6 fatty acids relative to C18:1 n‐9. Dry‐cured Landrace hams showed the lowest juiciness and tenderness, likely due to their lower fat content (marbling).     

Polymorphonuclear neutrophil granulocyte chemotactic hyperresponsiveness in a case of canine acromegaly

Growth hormone (GH) has recently been shown to affect polymorphonuclear neutrophil granulocyte (PMN) function and to be secreted by mononuclear cells, indicating that the hormone may be active in an immunophysiologic network, acting as an endo- or paracrine priming agent. The purpose of the present study was to evaluate the chemotactic responsiveness of canine peripheral PMN in a dog with acromegaly, caused by spontaneous, progesterone-induced hypersecretion of GH and, secondary to this, a seven-fold increase in insulin-like growth factor I (IGF-I). The chemotactic responsiveness towards zymosan-activated serum (ZAS) and leukotriene B4 (LTB4) was evaluated at a time when the dog suffered from acromegaly and again 57 days after corrective surgery (ovariohysterectomy). The experiments showed that PMN from the patient exhibited enhanced chemotactic migration that appeared to be associated with the hypersomatotropic condition as judged from the reversibility of the phenomenon. The glucose intolerance and elevated serum alkaline phosphatase that were observed in the acromegalic dog were also shown to be reversible following surgery.     

Buchbesprechungen

Ohne Zusammenfassung     

Optimization — a tool in advanced materials technology

This paper demonstrates the use of simple optimization techniques in the production of two advanced materials - a fibre-reinforced composite laminate and a transformation toughened ceramic - having enhanced mechanical properties. Both example materials are based on a brittle matrix prone to cracking at very low applied stresses. The optimization process aims at altering the microstructure so that the materials have enhanced resistance to crack propagation without any undesirable side effects.     

Cardiac risk in surgery. A review and guidelines for risk evaluation and reduction of cardiac risk in general surgery

We report herein the phenotypic and functional analysis of human bone marrow and thymus derived early T cells. Commitment to T cell lineage is acquired during CD7 antigen expression by CD34+ precursors in human bone marrow and before thymus colonization. Early thymocytes show similar phenotypic characteristics as bone marrow T cells. They rapidly acquire CD4 before the dual expression of CD4 and CD8. Their expansion and differentiation is regulated by two major factors: thymic stroma and cytokines produced by these stroma cells or by thymocytes themselves. Among cytokines, IL1 and sCD23 produced by thymic epithelial cells support in vitro early T cell development.     

Parabolic dish concentrators approximated by simple surfaces

Two different concentrating mirrors have been constructed that resemble parabolic dish reflectors. Both mirrors are made of slightly curved strips of flat, bendable material. The strips of the most simplified mirror have only large-radius circles and straight lines as boundaries. The necessary equations for making the mirrors are given. Also a simple way to make a stiff, lightweight frame and support for the mirror strips has been developed. Models of the mirrors have been built and successfully used for cooking and baking.     

Effect of specimen size and loading conditions on spalling of concrete

Different qualities of concrete have been fire tested using different geometries of the specimens as well as different load levels and load configurations. The main objective with the study was to examine a test methodology consisting of a full‐scale test and different small scale‐tests for determining the probability of spalling and the amount of spalling of fire exposed concrete structures. A reference specimen was defined as a one‐sided fire exposed slab with the dimensions 1800 × 1200 mm² giving an exposed area of 1500 × 1200 mm². A number of concrete qualities with different probabilities for spalling, were tested using the reference specimen. These tests showed that the reference specimens worked well giving the expected test results. Small specimens were manufactured in different shapes with the same concrete as the one used in the reference tests. These small specimens were tested either at the same time as the reference specimens in the large furnace or afterwards on a small‐scale furnace where the fire exposed surface was 450 × 360 mm². The test results clearly show the increased probability and the increased amount of spalling by using external compressive loading. The results also show that by using pre‐stress through bars or wires the load can be lost due to heating of the bars/wires which results in a decreased amount of spalling. The boundary of the specimen also affects the amount of spalling. The spalling around the edges was in all tests less than the spalling on the central parts of the exposed area. It could also be noted that the spalling did not pass completely through any of the specimens. The reason for this is probably that the water/vapour could migrate out from the unexposed surface of the specimen. Copyright © 2006 John Wiley & Sons, Ltd.     

Normative Systems and their Revision: An Algebraic Approach

The paper discusses normative systems and their revision within an algebraic framework. If a system is logically well-formed, certain norms, called connecting norms, determine the system as a whole. It is maintained that, if the system is well-formed, a relation “at least as low as” determines a lattice or quasi-lattice of its connecting norms. The ideas are presented mainly in the form of comments on a legal example concerning acquisition of movable property by extinction of another person's previous rights.