韩江三角洲海岸变迁遥感调查研究

利用1:10万TM影像，对广东东部韩江三角洲地区的海岸变迁及河道演变进行了调查研究。划分了不同时期的海岸界线和古河道遗迹，提出韩江三角洲的形成是河流动力和海洋动力共同作用的结果，对研究历史海平面变化及环境演变具重要意义。     

浅论油液质量对机械设备运转的影响

通过分析润滑油、液压油的质量对设备运转的影响，提出了使用润滑油、液压油的几点建议。     

活性污泥数学模型入流组分测定及应用

阐述了活性污泥1号模型人流组分的分析方法，并用这些方法测定了西安市城市污水水质。实验结果表明测定方法操作简单、准确可靠，能为利用模型进行污水处理厂的设计、模拟及管理提供入流组分分析依据，     

Preparation of Pb(Zr0.52Ti484848)O3 thin films on silicon-on-insulator substrates by excimer laser deposition combined with rapid thermal annealing

In this paper we report the fabrication of ferroelectric Pb(Zr_0.52Ti_0.48)O₃ (PZT) thin films on Si-on-Insulator (SOI) substrates with and without an electrode by pulsed excimer laser deposition combined with rapid thermal annealing. Based on the structural and interfacial characteristics analysis by X-ray diffraction (XRD), Rutherford backscattering spectroscopy (RBS), cross-sectional transmission electron microscopy (XTEM) and automatic spreading resistance measurement (ASR), the film structure and orientation were revealed to be dependent on the annealing time and annealing temperature as well as deposition temperature. From RBS spectra and XTEM observation it is shown that the PZT thin films did not interact with the top silicon layers of SOI and that the composition of the film was similar to the target. The ASR measurements showed that the electrical properties of PZT/SOI as well as PZT/Pt/SOI were abrupt, and that the electrical properties of the SOI substrates were still good after the PZT growth.     

SBR工艺污泥膨胀的纠正方法

在对国内外有关资料的研究基础上，介绍了几种应对SBR反应池内污泥膨胀的措施。着重叙述了氯化法和无机合成絮凝剂法的应用注意点及如何定量运用这两种方法，同时给出了相应的工程实例。     

DC-DC变换器突加负载时的动态性能研究

提出了一种能够有效改善DC-DC变换器动态性能的方案。该方案是在全桥电路基础上并联一单端正激变换电路，使变换器负载从10%轻载突加到100%满载时，其暂态过程小于1μs输出电压达到设计要求。文中对具体电路进行了详细分析，并通过仿真进行了验证。     

脉冲激光沉积SrBi2Ta2O9铁电薄膜电容特性研究

用ＰＬＤ方法成功地制备了ＳＢＴ铁电薄膜，并制作成Ｐｔ／ＳＢＴ／Ｐｔ薄膜电容器。ＳＢＴ薄膜的晶面取向以（００８）和（１１５）为主。在５Ｖ电压下，极化反转，并且得到较饱和的电滞回线，剩余极化强度和矫顽电场分别为８４μＣ／ｃｍ２和５７ｋｖ／ｃｍ。ＩＶ特性测试显示两个对称的双稳峰，并得到零电压下，面积为３１４×１０４μｍ２，厚度为０３５μｍ的电容器，电容约为５６０ｐＦ，介电常数约为６００。疲劳测试表明Ｐｔ／ＳＢＴ／Ｐｔ具有优良的抗疲劳特性。     

影响聚合物段塞流变性因素的研究

本文针对我国表面活性剂/聚合物驱油的实际,研究了石油磺酸盐(PS)、正丁醇(R_4OH)和矿化水对水解聚丙烯酰胺(HPAM)溶液流变性的影响。结果表明,PS对HPAM溶液流变性的影响与介质的矿化度有关:非矿化水介质中,PS对HPAM溶液性质的影响类似于无机盐,能降低HPAM溶液的表现粘度(η_α)和稠度系数(k);当系统中含有一定浓度矿化水时,PS却能升高系统的η_α和k值,降低流型指数(n),使系统的非牛顿性增强。在含有PS和矿化水的HPAM系统中加入R_4OH,系统的η_α和k值会有所增加。     

In situ synthesis of TiC-Al (Ti) nanocomposite powders by thermal plasma technology

A novel processing technology was developed to investigate in situ synthesis of TiC-Al (Ti) nanocomposite powders by thermal plasma technology. Thermodynamic analysis was performed to predict possible starting materials and synthesizing conditions of TiC-Al (Ti) nanocomposite powders. A mathematical model was developed to describe temperature profile and velocity distribution in the reactor. The model is applied to optimize feeding rate, input power, and other processing parameters of TiC-Al (Ti) nanocomposite powders by thermal plasma technology, and to predict which materials can be used as starting materials. This paper emphasizes the investigation of the effect of feeding rate, input power, mole ratio, and other process parameters on synthesis of TiC-Al (Ti) nanocomposite powders by thermal plasma technology. The experimental results showed that TiC-Al (Ti) nanocomposite powders can be synthesized in situ by thermal plasma technology, and the average size of TiC-Al (Ti) nanocomposite powders was less than 100 nm.     

提高热轧带卷的成材率途径

莱钢1500mm热轧生产线于2005年6月投产。通过对轧钢生产过程中各环节的有效控制,使成材率显著提高,居于全国同行业领先水平,取得了良好的经济效益。