Optimization of printing parameters for improvement of mechanical and thermal performances of 3D printed poly(ether ether ketone) parts

Many processing parameters can be adjusted to optimize the fused filament fabrication (FFF) process, a popular and widely used additive manufacturing techniques for plastic materials. Among those easily adjusted parameters are the nozzle temperature, printing speed, raster orientation, and layer thicknesses. Using poly(ether ether ketone) (PEEK) as the base material, a design of experiments analysis was performed on the main FFF parameters. A response surface methodology was applied to analyze the results and to maximize the output responses. Results have shown that the nozzle temperature is the most influential parameter on tensile properties and the crystallinity degree of printed PEEK by FFF process. Parts produced with optimized FFF parameters were then subjected to an annealing treatment to induce a relaxation of residual stress and to enhance crystallinity. The best properties for 3D printed PEEK parts were achieved with annealed parts prepared at 400°C with a printing speed of 30 mm/s, 0.15 mm layer thickness and raster orientation of [0°/15°/−15°]. The resulting parts have mechanical properties comparable to those of injected PEEK.     

Probing the Vorticity in a Superconductor Rapidly Quenched from the Normal State

Topological defects such as vortices subsist for some time in a rapidly frozen superconducting film (W. H. Zurek, Phys. Rep. 276, 177, 1996). We propose to use as a probe of the vortex density the finite delay T _d, which, in narrow strips, exists between a current step and the voltage response. Technically, this amounts to driving a bridge into the localized hot-spot regime by means of a pump pulse (laser or electrical). Cooling of such films as epitaxial YBCO-on-MgO, or niobium-on-sapphire, requires only a few nanoseconds at low T. A time t later, a probe pulse is applied to measure T _d. The dependence t T _d is interpreted as a witness of the fossil vorticity, long after quenching into the zero-resistance regime.     

周期性输入组分和扫气在改善钯膜反应器甲烷部分氧化制氢中的作用(英文)

The partial oxidation of methane under periodic operation over Ni/γ-Al2O3 catalyst was investigated in a Pd-membrane reactor.The effects of key parameters such as the inlet composition and the sweeping gas on methane conversion and the hydrogen recovery are numerically established with two periodic input functions.In order to analyze the effect of the inputs modulation,the reaction was performed under low steam to methane ratio at a moderate temperature and pressure.It was obtained that to achieve process intensification is to operate the process in a periodic way.The main results show that the periodic input functions can improve the performance of the process compared to the optimal steady state operation.Moreover,there is an optimum amplitude of manipulated inputs leads to a maximum of hydrogen recovery.It is noteworthy that the comparison between the predicted performance via the sinusoidal and the square ways show that the better average performance was obtained with the square way.     

Removal turbidity and separation of heavy metals using electrocoagulation-electroflotation technique A case study

The electrocoagulation (EC) process was developed to overcome the drawbacks of conventional wastewater treatment technologies. This process is very effective in removing organic pollutants including dyestuff wastewater and allows for the reduction of sludge generation. The purposes of this study were to investigate the effects of the operating parameters, such as pH, initial concentration (C(0)), duration of treatment (t), current density (j), interelectrode distance (d) and conductivity (kappa) on a synthetic wastewater in the batch electrocoagulation-electroflotation (EF) process. The optimal operating conditions were determined and applied to a textile wastewater and separation of some heavy metals. Initially a batch-type EC-EF reactor was operated at various current densities (11.55, 18.6, 35.94, 56.64, 74.07 and 91.5mA/cm(2)) and various interelectrode distance (1, 2 and 3cm). For solutions with 300mg/L of silica gel, high turbidity removal (89.54%) was obtained without any coagulants when the current density was 11.55mA/cm(2), initial pH was 7.6, conductivity was 2.1mS/cm, duration of treatment was 10min and interelectrode distance was 1cm. The application of the optimal operating parameters on a textile wastewater showed a high removal efficiency for various items: suspended solid (SS) 86.5%, turbidity 81.56%, biological oxygen demand (BOD(5)) 83%, chemical oxygen demand (COD) 68%, and color over 92.5%. During the EC process under these conditions, we have studied the separation of some heavy metal ions such as iron (Fe), nickel (Ni), copper (Cu), zinc (Zn), lead (Pb) and cadmium (Cd) with different initial concentrations in the range of 50-600mg/L and initial pH between 7.5 and 7.8. This allowed us to show that the kinetics of electrocoagulation-electroflotation is very quick (<15min), and the removal rate reaches 95%.     

Resolution Improvement of Ultrasonic Signals Using Sparse Deconvolution and Variational Mode Decomposition Algorithms

Russian Journal of Nondestructive Testing - Over the past few years, the use of ultrasonic arrays for nondestructive testing (NDT) applications has grown rapidly and led to use new algorithms of...