Efficient Design of Bi-circular Patch Antenna for 5G Communication with Mathematical Calculations for Resonant Frequencies

Wireless Personal Communications - In this paper the conventional circular patch has been reshaped by two circular arcs with the FR4 Epoxy material for substrate. This is supported by the...     

Mathematical model for computer simulation and control of steelmaking

A dynamic model for computer simulation and control of steelmaking has been developed. It is essentially based on multicomponent mixed transport control theory with the incorporation of energy balance calculations. The model is applicable to both steelmaking in electric furnaces as well as in oxygen steelmaking converters. The adjustable parameters of the model for simulation of oxygen steelmaking are gas evolution rate (G_co). oxygen flux factor (F_o) and emulsification factor (EM). These simulation parameters, when combined with on-line measurement of off-gas composition and temperature, enable complete dynamic control of the process. The model developed is applied, as an example, to an industrially produced heat in a top blown oxygen steelmaking converter and the results of simulation are discussed.     

Design of a wideband microstrip antenna and the use of artificial neural networks in parameter calculation

This paper deals with the design of a multi-slot hole-coupled microstrip antenna on a substrate of 2 mm thickness that gives multi-frequency (wideband) characteristics. The Method of Moments (MoM)-based IE3D software was used to simulate the results for return loss, VSWR, the Smith chart, and the radiation patterns. A tunnel-based artificial neural network (ANN) was also developed to calculate the radiation patterns of the antenna. The radiation patterns were measured experimentally at 10.5 GHz and 12 GHz. The experimental results were in good agreement with the simulated results from IE3D and those of the artificial neural network. A new method of using a genetic algorithm (GA) in an artificial neural network is also discussed. This new method was used to calculate the resonant frequency of a single-shorting-post microstrip antenna. The resonant frequency calculated using the genetic-algorithm-coupled artificial neural network was compared with the analytical and experimental results. The results obtained were in very good agreement with the experimental results.     

Fast computation of multidimensional discrete Hartley transform

Efficient algorithms for the fast computation of 2D and 3D discrete Hartley transforms have been proposed. It is shown that the proposed algorithms offer a significant saving in computation over the existing methods for various array sizes.<>     

IEEE-PES Transmission and Distribution Conference and Exposition Call for Papers

Static network-related system voltage stability margin (VSM) depends on the availability of reactive power to support the transport of real power from sources to sinks. Based on this premise, the total VAr loss is minimized in the unified OPF framework considering real and reactive power controllers, and its effect on VSM is studied. Studies are conducted on a three-bus system, the IEEE 30-bus system, and a 191-bus Indian electric power system, and their results are reported.     

Thermal shock and thermal fatigue study of ceramic materials on a newly developed ascending thermal shock test equipment

A test equipment was designed to study thermal shock and thermal fatigue of ceramic materials subjected to fast heating (ascending). The equipment was designed to generate thermal stress in a test specimen by heating one surface of it by an oxy-hydrogen flame while cooling the opposite surface. The sample cracked when thermal stress exceeded its mechanical strength. The in situ crack formation was detected by an acoustic emission system coupled to the set up. The hot zone temperature was measured by an infra red pyrometer. The equipment was also designed to run thermal fatigue test cycles in automatic mode between two selected temperatures. The temperature and thermal stress distribution in the test specimen were modelled using finite element software. The effect of temperature distribution of the top and bottom surfaces on thermal stresses was studied. It was observed that the thermal stress is very sensitive to the temperature distribution on the top surface and maximum near the periphery of the top surface. This was in agreement with the experimental results in which the cracks were originated from the periphery of top surface. It was also observed that the failure temperature was higher for thicker samples.     

Synthesis of ductile titanium-titanium boride (Ti-TiB) composites with a beta-titanium matrix: The nature of TiB formation and composite properties

The study focused on the in-situ synthesis of titanium (Ti)-titanium boride (TiB) composites with β phase in the matrix by reaction sintering of TiB₂ with Ti and alloying element powders. The goal was to examine the nature of TiB whisker formation in three different kinds of powder mixtures: (1) β-Ti alloy powders and TiB₂; (2) α-Ti powder, a master alloy (Fe-Mo) powder containing the β-stabilizing elements, and TiB₂; and (3) α-Ti powder, a β-stabilizing elemental powder (Mo or Nb), and TiB₂. The effects of powder packing and the relative locations of powder particles on the morphological changes in TiB whisker formation and their growth were studied at processing temperatures ranging from 1100°C to 1300°C. The morphology, size, and distribution of whiskers were found to be influenced by the powder-packing conditions. A large particle-size ratio in bimodally packed mixtures led to the formation of a TiB monolithic layer around β grains. With a relatively finer starting powder, smaller size ratio, and trimodal packing arrangement, the TiB whiskers were found to be distributed more homogeneously in the matrix. The study also used the X-ray direct comparison method and the structure factor for the β phase to determine the volume fraction of TiB phase from X-ray data. Tensile tests and fractographic investigations were carried out on selected composites. The evolution of the composite microstructure, the influence of powder-packing variables, and the morphology and growth of TiB whiskers and their effect on mechanical properties are discussed.     

Microwave-Assisted Synthesis of Fine Particle Oxides Employing Wet Redox Mixtures

Interaction of electromagnetic radiation with a physical mixture of metal nitrates and amides/hydrazides is observed to initiate high-temperature reactions, useful for realizing several high-temperature ceramic materials. A judicious choice of such redox mixtures undergoes exothermic reactions when they couple with microwave radiation. The coupling of electromagnetic radiation with metal salts and amides/hydrazides depends on the dielectric properties of the individual components in the reaction mixture. The approach has been used to prepare γ-Fe₂O₃, Fe₃O₄, MgCr₂O₄, α-CaCr₂O₄, and La_0.7Ba_0.3MnO₃.     

A novel sine augmented scaled sine cosine algorithm for frequency control issues of a hybrid distributed two-area power system

Neural Computing and Applications - In this research article, a novel approach is proposed by considering the sine augmented scaled sine cosine (SAS-SCA) Algorithm for the load frequency control of...