A 300-MHz 25-/spl mu/A/Mb-leakage on-chip SRAM module featuring process-variation immunity and low-leakage-active mode for mobile-phone application processor

An on-chip 1-Mb SRAM suitable for embedding in the application processor used in mobile cellular phones was developed. This SRAM supports three operating modes - high-speed active mode, low-leakage low-speed active mode, and standby mode - and uses a subdivisional power-line control (SPC) scheme. The combination of three operating modes and the SPC scheme realizes low-power operation under actual usage conditions. It operates at 300 MHz, with leakage of 25 /spl mu/A/Mb in standby mode, and 50 /spl mu/A/Mb at the low-leakage active mode. This SRAM also uses a self-bias write scheme that decreases of minimum operating voltage by about 100 mV.     

Soft X-ray image storage in poly (methylmethacrylate)

Images stored in resist for soft X-ray lithography or microradiography were found to show a background noise which limits the resolution. This is due to the statistically variable spatial distribution of the photons incident on the resist surface. An estimate of the fundamental noise-limited resolution has been made from the experimental measurement of photon flux incident on the surface and the accurate development rate curves. Monochromatic radiation from a synchrotron source was used.     

Problem pharmaceutical patents

These days, the number of pharmaceutical patent applications which do not specify the principal active ingredient in the form of a chemical name or structure is increasing. These patents are difficult to retrieve in retrospective on-line searches using chemical structures or keywords. Furthermore, even if you could find them, the situation with regard to patentability is obscure and this causes considerable problems for the experts in charge of the patent search. If you are a searcher for a large pharmaceutical company, you might already be apprehensive of infringing such patents. We, the JFA,^* gathered these patents together and studied the differences between their patentability in Japan, the US and the EPO.     

ATMPKs: a gene family of plant MAP kinases in Arabidopsis thaliana

We previously reported two cDNAs for MAP kinases (cATMPK1 and cATMPK2) from a dicot plant, Arabidopsis thaliana. We describe here the cloning and characterization of five additional cDNAs encoding novel MAP kinases in Arabidopsis, cATMPK3, cATMPK4, cATMPK5, cATMPK6, and cATMPK7. The amino acid residues corresponding to the sites of phosphorylation (Thr-Glu-Tyr) that are involved in the activation of animal MAP kinases are conserved in all the seven putative ATMPK proteins. Genes for MAP kinases in Arabidopsis constitute a family that contains more than seven members. Sequence analysis suggests that there are at least three subfamilies in the family of Arabidopsis genes for MAP kinases.     

Superplastic behaviour of Ti-48at.%Al two-phase titanium aluminide compacts made from mechanically alloyed powder

An HIP compact of MA-processed powder having a nominal composition of Ti-48at.% Al was produced. The compact consisted of a large amount of TiAl(λ) and a small amount of Ti₃Al (₂), in a completely ultra-fine equiaxed grain structure. This two-phase compact showed typical superplastic deformation behaviour. A maximum elongation of 550% was obtained. A strain exponent, n = 2, and grain size exponent, p = 2, were determined from the results of a strain-rate-change test and a creep test at constant initial stress using samples having various grain sizes, respectively. The activation energy for creep, Q_c at constant stress was calculated to be 350 kJ/mole. It is concluded that the superplastic deformation mechanism of the material under study is grain boundary sliding controlled by lattice diffusion in the TiAl phase.     

Design optimization of tall tubular lead/acid cells based on an analysis of the reaction distribution

In order to estimate the discharge performance of tall lead/acid cells (with tubular positives), changes in current and potential distributions with discharge progress were calculated with a computer on the basis of plate resistance and the current—potential—time relationship between small facing parts of positive and negative plates. The taller the cell, the larger the voltage drop along the plates. Thus, the discharge time became shorter despite a large amount of available active mass remaining in the bottom part of the plates.Various current-collector designs were evaluated, e.g., one with varying resistance at each height; a side conductor placed along the plates and connected to them at the top, centre and bottom, etc. Results revealed an optimum collector design with which the maximum discharge capacity could be obtained. Furthermore, it was shown that the side conductor markedly improved the discharge performance because the active mass near the connecting parts was appreciably used.     

Reexamination of grain-boundary sliding by diffusion

Steady-state sliding of grain boundaries is discussed by taking into account the change in the potential energy of an applied stress, when the sliding occurs by diffusional accommodation. The present analysis enables us to derive the sliding rates at boundaries of various shapes in a simple manner without knowing local stress fields. Sliding rate of a boundary containing second phase particles is also derived by similar calculations. The results are compared with previous calculations by other investigators, and it is found that the resultant expressions for the sliding rates are essentially identical to those derived from more complex analyses.     

90-nm process-variation adaptive embedded SRAM modules with power-line-floating write technique

The power consumption of a low-power system-on-a-chip (SoC) has a large impact on the battery life of mobile appliances. General SoCs have large on-chip SRAMs, which consume a large proportion of the whole LSI power. To achieve a low-power SoC, we have developed embedded SRAM modules, which use some low-power SRAM techniques. One technique involves expanding the write margin; another is a power-line-floating write technique, which enables low-voltage write operation. The power-line-floating write technique makes it possible to lower the minimum operating supply voltage by 100 mV. The other techniques involve using a process-variation-adaptive write replica circuit and reducing leakage current. These techniques reduce active power during write operations by 18% and reduce active leakage of the word-line driver by 64%. The prototype SRAM modules achieve 0.8-V operation, and a 512-kb SRAM module achieves 48.4-/spl mu/A active leakage and 7.8-/spl mu/A standby leakage with worst-leakage devices.     

Discharge behaviour of electrodeposited PbO2 and Pb electrodes

The discharge behaviour of electrodeposited lead dioxide and lead electrodes was investigated under various conditions; the surfaces of the discharged electrodes were observed with a scanning electron microscope. Both the positive and negative electrodes were passivated by a covering of deposited lead sulphate crystals. The amount of lead sulphate required for passivation depended on the size of the crystals.     

Air bubbles in the subclavian or internal jugular veins: a common finding on contrast-enhanced CT

BACKGROUND: Foot complications in diabetes incur huge human and medical costs. There is a high incidence of complicated diabetes mellitus in Far North Queensland, particularly in the indigenous communities. METHODS: An audit of 51 patients admitted to Cairns Base Hospital from July 1992 to December 1994 with diabetic foot complications requiring surgical intervention was performed. RESULTS: The majority of surgical procedures were for serious infections in neuropathic feet precipitated by minor trauma. Surgical procedures included debridement/drainage, minor amputation, major amputation and arterial bypass. Half of the patients required more than one procedure and/or multiple admissions. Average length of stay was 48 days. Indigenous patients were overrepresented in this audited group. CONCLUSIONS: Prevention or minimization of diabetic foot complications can be achieved only through improvement in education and vigilance at all levels of the treatment process from community to hospital. Special attention to the needs of indigenous communities with a high incidence of diabetes must be a feature of any future initiatives.