Robust vector control of induction motors using full-order observer in consideration of core loss

This paper proposes a method for designing a robust full-order observer for vector-controlled induction motors taking core loss into account. Although conventional research focuses on parameter identification, global stability of the identification remains questionable. Therefore, robustness against some parameters is required. This paper describes the design of a robust full-order observer which takes core loss into account, using both the gain-scheduled H/sub /spl infin// control and the linear matrix inequality technique. This design always results in a stable controller. The robustness of the proposed method against variations of resistances is evaluated by experiments.     

Efficiency of repeated batch penicillin fermentation using two fermentors. Computer simulation and optimisation

Repeated batch operation using two fermentors (RBTF) to penicillin fermentation was demonstrated by computer simulation to improve productivity. Three operation modes were compared: chemostat, repeated batch operation using a single fermentor (RBSF) and RBTF; in each case account was made of the lag period before growth. The simulated fermentor performances were assessed on the basis of the penicillin productivity and concentration; the simulation was based on published batch fermentation data. It was shown that RBTF was superior to RBSF and chemostat. The advantage of RBTF increased as the lag period became greater.     

Preparation and antibacterial activity of novel fluoroalkyl end-capped oligomers/silica nanocomposites-encapsulated low molecular biocides

Fluoroalkyl end-capped N-(1,1-dimethyl-3-oxobutyl)acrylamide oligomer [R_F-(DOBAA) _n -R_F] reacted with tetraethoxysilane (TEOS) and silica nanoparticles in the presence of low-molecular weight biocides such as hibitane, hinokitiol, and hinokioil under alkaline conditions to afford R_F-(DOBAA) _n -R_F/silica nanocomposites-encapsulated these biocides in excellent to moderate isolated yields. Fluoroalkyl end-capped N,N-dimethylacrylamide oligomer [R_F-(DMAA) _n -R_F] and acrylic acid oligomer [R_F-(ACA) _n -R_F]/silica nanocomposites-encapsulated hibitane were obtained under similar conditions. Dynamic light scattering measurements showed that the size of these fluorinated nanocomposites-encapsulated biocides thus obtained is nanometer size-controlled. Additionally, these fluorinated nanocomposites were shown to have a good dispersibility and stability in methanol and water. Of particular interest, these fluorinated nanocomposites-encapsulated biocides were found to have a good antibacterial activity against Staphylococcus aureus, and these nanocomposites were applied to the surface modification of traditional organic polymers such as poly(methyl methacrylate).     

Differentiation of Arthroderma spp. by random amplification of polymorphic DNA (RAPD) and Southern hybridization

To develop the molecular differentiation analysis of dermatophytes, we carried out RAPD and Southern hybridization analyses using genomic DNAs of six Arthroderma species, including A. fulvum, A. grubyi, A. gypseum, A. incurvatum, A. otae and A. racemosum. The RAPD analysis gave different band patterns specific to each of the six Arthroderma fungi. However, minor differences in the banding patterns were observed between the strains of plus (+) and minus (-) mating types of A. gypseum, A. fulvum and A. incurvatum. Southern blot analysis using a probe (1S) obtained from A. grubyi DNA gave specific bands only in the DNA samples of A. grubyi and A. incurvatum. On the other hand, Southern blot analysis using a probe (C3) obtained from A. otae DNA gave specific bands in all six Arthroderma species examined, and the size of the bands were specific to each species. These findings indicate that RAPD and Southern hybridization analyses are useful in the differentiation of these Arthroderma species.     

Heat Capacity of 3He Solid Film on Graphite in Magnetic Fields

Heat capacities of a submonolayer ³He solid film adsorbed on a graphite surface are measured in magnetic fields up to 400 Oe. The measured heat capacity shifts to higher temperatures with an increasing magnetic field. The amplitudes of the shifts are twenty times larger than the magnitude of the Zeeman energy, which is anomalously large. With regard to the origin of these large shifts, the reduction of frustrations and the weakening of the competition between multiple spin exchange interactions are discussed.     

Phenol novolac/poly(4- hydroxyphenylmaleimide) blend hardeners for DGEBA-type epoxy resin

Phenol novolac/poly (4-hydroxyphenylmaleimide) (PHPMI) blends were used as an epoxy resin hardener. The curing behavior of the above system and the thermal and mechanical properties of the cured epoxy resin were studied. It was not necessary to use a curing accelerator for this system, because PHPMI caused acceleration of the curing reaction. The curing mechanism of this system was investigated by using model compounds. Test pieces from the neat resins and the glass fiber reinforced resins were evaluated in terms of thermal and mechanical properties, respectively. It was found that heat resistance and mechanical properties were improved by increasing the amount of PHPMI in the hardener.     

EXPANSION AND STRESS RELAXATION OF EXPRESSED CAKE

Expansion and stress relaxation of expressed cake are discussed.

The expansion process of expressed cake after release of load is very similar to consolidation of solidndashliquid mixtures, although a liquid flow in the expansion process is opposite in direction to that in consolidalion. This process can be analyzed well by use of the Terzaghi Voigt combined model. It is shown that the rate of primary deformation in expansion is much smaller than that in consolidation under the same change in compressive pressure. It is also found that the ratio of secondary deformation to total deformation in expansion is much larger than that in consolidation.

Stress relaxation of expressed cake, which is observed when expression is stopped before attaining an equilibrium compression state of a material, can be explained by use of a consolidation and expansion theory. In the relaxation process, local expansion appears near the drainage surface while local consolndash idation appears near the center of the cake. The equilibrium cake stress is uniquely determined by the average consolidation ratio when the expression is interrupted.     

A case of macrocystic cervical neurinoma diagnosed by MRI with Gd-DTPA

The authors report a rare case of a large cystic cervical neurinoma. A 45-year-old female was admitted to our clinic because of motor weakness of the right upper extremity, numbness of the right fingers and right posterior cervical pain. Metrizamide CT myelography demonstrated the outline of a low density mass. MRI showed a mass revealing low signal intensity on T1-weighted image, high signal intensity on T2-weighted image and marginal enhancement on contrast image with Gd-DTPA. The mass which was diagnosed as cystic tumor, was located in the intradural extramedullary space between C4 to C5 segments. After C4 through C5 laminectomy, the tumor was found to originate from the C5 anterior motor root. The tumor consisted mostly of a cystic part with a very thin solid compartment beneath the capsule. Postoperative course of the patient was uneventful. Although spinal neurinoma is one of the most common spinal tumors, an almost completely degenerated large cystic spinal neurinoma is extremely rare. MRI with Gd-DTPA was useful for the diagnosis of the cystic neurinoma by clearly enhancing the margin of the tumor.     

Continuous formation of slurry ice by cooling water–oil emulsion in a tube

Water-silicone oil emulsion with an additive, (C₂H₅O)₃SiC₃H₆NH₂, was examined as a heat storage material. A spiral tube used as a heat exchanger was immersed in a low temperature bath and the emulsion was circulated in the tube to make ice continuously. Ice was separated from the ice–liquid suspension in an outlet tank. The amount of formed ice, the temperatures of the inlet and the outlet of the heat exchanger, and the temperatures in the tube wall were measured and the overall heat transfer coefficient and the heat flux through the tube were calculated. Experiments were carried out, varying the flow rate, the temperature of cooling brine, and the thickness of tube wall. The condition under which slurry ice was formed continuously without adhesion of ice to the cooling wall was clarified. Though decrease in the thermal resistance of the tube increased the rate of ice formation or raised the brine temperature, it narrowed the range of the flow rate and of the brine temperature in which slurry ice was formed continuously.