Electrical Breakdown Properties and Space Charge Formation in High Temperature Region in Ultraviolet Ray Irradiated PVC

Polyvinyl chloride (PVC) is the most popular insulating material for electric wiring instruments. However, an exothermic reaction above 150 °C may cause deterioration of the insulating properties of PVC. Therefore, it is important to clarify the heat degradation in PVC, not only to investigate the ignition of electrical wiring products but also to use electrical products safely. It is known that ultraviolet (UV) irradiation causes chemical deterioration of PVC and an increase in its conductivity. Generally, it has been thought that the electrical breakdown properties, electrical conduction, and insulating performance are affected by space charge accumulation in an insulating material. A high temperature pulsed electroacoustic (PEA) system usable up to 250 °C has been developed, and the PEA system can measure the space charge distribution and conduction current in the high temperature range simultaneously. In this investigation, the space charge distribution and conduction current were measured up to electrical breakdown in a non‐UV irradiated sample (normal PVC) and in 353 nm and 253 nm UV‐irradiated PVC samples in the range from room temperature to 200 °C in a DC electric field. In the short wavelength UV irradiated PVC sample (253 nm, 300 h), a deterioration of breakdown strength at 90 °C to 150 °C and negative packet‐like charges were observed at 60 °C and 100 °C, a positive charge accumulated in front of both the anode and cathode above 90 °C, and a higher electric field near the cathode side because the positive charge of the cathode side was greater.     

Quality-Assurance Technology in Japan

A survey of the state of SQA in Japan finds that the situation is much like, but slightly different than, that in the US.     

Autonomic nervous function of the patients with neurally mediated syncope

Although diagnosis of neurally mediated syncope (NMS) using head-up tilt (HUT) test has been established, the exact mechanism of NMS has not yet been elucidated. We evaluated beta and alpha-adrenergic function in NMS patients by pharmacological autonomic function test. The alpha-adrenergic sensitivity of NMS patients was significantly lower than that of control subjects. The patients who need low dose isoproterenol for provocation of syncope showed higher beta-adrenergic sensitivity than patients who developed syncope without isoproterenol. Thus, pharmacological autonomic function test was useful for evaluation of NMS patients.     

Adhesion between polymer surface modified by graft polymerization and tissue during surgery using an ultrasonically activated scalpel device

In the field of surgery, achieving adhesion between a polymer implant and tissue poses a challenge considering that suturing is not appropriate for the stability of such implants. An ultrasonically activated scalpel that generates heat by mechanical vibration and promotes adhesion between a polymer implant and native tissue by pressing the two materials together has very good potential for application in the field. To determine the type of polymer that is suitable for the purpose, we investigated polyethylene (PE) and polystyrene (PS) films, the surfaces of which were activated by corona discharge. Graft polymerization was then performed on the corona‐treated surfaces to vary their properties. The corona‐treated PE and PS films grafted with poly(acrylic acid), poly(methacrylic acid), poly(vinyl benzylacrylic acid), and poly(hydroxylethyl acrylate), respectively, adhered to the tissue when the ultrasonically activated scalpel was applied. The heat generated by the mechanical vibration and the applied pressure enabled the carboxyl or hydroxyl groups to bond with the proteins in the extracellular matrix. We therefore concluded that it was possible to integrate this technique in the development of new types of polymer devices that could be stably implanted in a living body. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40885.     

Novel functional polymers: Poly(dimethylsiloxane)–polyamide multiblock copolymer. III. Synthesis and surface properties of disiloxane–aromatic polyamide multiblock copolymer

Disiloxane–aromatic polyamide(aramid) multiblock copolymers(2SiPASs) were synthesized using 1,3-bis(3-aminopropyl)-1,1,3,3-tetramethyldisiloxane(BATS) as an analog of aramidsilicone resin consisting of aromatic polyamide and poly(dimethylsiloxane) (PDMS). 2SiPASs afford a transparent and toughened plastic film. The surface properties of 2SiPAS were investigated by X-ray photoelectron spectroscopy (xps) and static contact angle measurement. The results of surface analysis suggested that BATS content of the 2SiPAS surface increased with increasing BATS content in bulk. The interaction between the platelets and the 2SiPAS surface was found to be very weak when the BATS content reached 26 wt % in bulk. © 1996 John Wiley & Sons, Inc.