Spray dryer processed graphene oxide/reduced graphene oxide for high-performance supercapacitor

This study deals with the utility of mini spray dryer process to improve the dispersibility, of graphene oxide(GO) and its application for high-performance supercapacitor. Initially, the neutral solution of GO was obtained using the modified Hummer's method. After this, the prepared GO solution was processed by mini spray dryer to obtain a more purified, lighter, and dispersed form of GO which is named as spray dryer processed GO (SPGO). The SPGO thus obtained showed excellent dispersibility behavior with various solvents, which is not found in case of conventional oven drying. Furthermore, utility of SPGO and its reduced form (r-SPGO) for supercapacitor applications have been investigated. Results obtained from the cyclic voltammetry(CV) analysis, impedance, and charge-discharge behavior of supercapacitor fabricated using r-SPGO shows enhanced features. Therefore, the simple spray dried GO and its reduced form, that is, r-SPGO can be utilized as a potential candidate for the supercapacitor application. Herein, as synthesized SPGO exhibited the specific capacitance of 12.07 and 37.6 F/g with PVA-H₃PO₄ and 1 mol/L H₃PO₄, respectively, at a scan rate of 5 mV/s. On the other hand, reduced form of SPGO, that is, r-SPGO showed the specific capacitance of 27.16 and 230 F/g with PVA-H₃PO₄ and 1 mol/L H₃PO₄, respectively.     

Design,Synthesis, and Self-Assembly Studies of a Suite of Monodisperse,Facially Amphiphilic,Protein–Dendron Conjugates

The custom design of protein–dendron amphiphilic macromolecules is at the forefront of macromolecular engineering. Macromolecules with this architecture are very interesting because of their ability to self-assemble into various biomimetic nanoscopic structures. However, to date, there are no reports on this concept due to technical challenges associated with the chemical synthesis. Towards that end, herein, a new chemical methodology for the modular synthesis of a suite of monodisperse, facially amphiphilic, protein–dendron bioconjugates is reported. Benzyl ether dendrons of different generations (G1–G4) are coupled to monodisperse cetyl ethylene glycol to form macromolecular amphiphilic activity-based probes (AABPs) with a single protein reactive functionality. Micelle-assisted protein labeling technology is utilized for site-specific conjugation of macromolecular AABPs to globular proteins to make monodisperse, facially amphiphilic, protein–dendron bioconjugates. These biohybrid conjugates have the ability to self-assemble into supramolecular protein nanoassemblies. Self-assembly is primarily mediated by strong hydrophobic interactions of the benzyl ether dendron domain. The size, surface charge, and oligomeric state of protein nanoassemblies could be systematically tuned by choosing an appropriate dendron or protein of interest. This chemical method discloses a new way to custom-make monodisperse, facially amphiphilic, protein–dendron bioconjugates.     

Separation of hematite from banded hematite jasper (BHJ) by magnetic coating

The separation of iron oxide from banded hematite jasper(BHJ) assaying 47.8% Fe, 25.6% Si O2 and 2.30%Al2O3 using selective magnetic coating was studied. Characterization studies of the low grade ore indicate that besides hematite and goethite,jasper, a microcrystalline form of quartzite, is the major impurity associated with this ore. Beneficiation by conventional magnetic separation technique could yield a magnetic concentrate containing 60.8% Fe with 51% Fe recovery. In order to enhance the recovery of the iron oxide minerals, fine magnetite, colloidal magnetite and oleate colloidal magnetite were used as the coating material. When subjected to magnetic separation, the coated ore produces an iron concentrate containing 60.2% Fe with an enhanced recovery of56%. The AFM studies indicate that the coagulation of hematite particles with the oleate colloidal magnetite facilitates the higher recovery of iron particles from the low grade BHJ iron ore under appropriate conditions.     

Mathematical model for computer simulation and control of steelmaking

A dynamic model for computer simulation and control of steelmaking has been developed. It is essentially based on multicomponent mixed transport control theory with the incorporation of energy balance calculations. The model is applicable to both steelmaking in electric furnaces as well as in oxygen steelmaking converters. The adjustable parameters of the model for simulation of oxygen steelmaking are gas evolution rate (G_co). oxygen flux factor (F_o) and emulsification factor (EM). These simulation parameters, when combined with on-line measurement of off-gas composition and temperature, enable complete dynamic control of the process. The model developed is applied, as an example, to an industrially produced heat in a top blown oxygen steelmaking converter and the results of simulation are discussed.     

Lean philosophy: implementation in a forging company

This research addresses the implementation of lean philosophy in a forging company with a focus on radial forging production flow lines. Here, the prime motive is to evolve and test several strategies to eliminate waste on the shop floor. In this research, a systematic approach is suggested for the implementation of lean principles. This paper describes an application of value stream mapping (VSM). Consequently, the present and future states of value stream maps are constructed to improve the production process by identifying waste and its sources. Furthermore, Taguchi’s method of design of experiments is pursued here to minimize the forging defects produced due to imperfect operating conditions. A noticeable reduction in set-up time and work-in-process (WIP) inventory level is substantiated. Finally, we conclude with a discussion of managerial implications and the future scope of research.     

Fuzzy Multiobjective and Linear Programming Based Management Models for Optimal Land-Water-Crop System Planning

In this article, linear programming and fuzzy optimization models are developed for planning and management of available land-water-crop system of Mahanadi-Kathajodi delta in eastern India. The models are used to optimize the economic return, production and labour utilization, and to search the related cropping patterns and intensities with specified land, water, fertilizer and labour availability, and water use pattern constraints. Due to extreme backwardness of the study area, it has been decided to keep all the three objectives of the linear programming models at the same priority level to obtain the compromised solution in a fuzzy environment that incorporates the imprecision in fuzzy goals and fuzzy constraints. These non-structural models facilitate the conjunctive use of available surface water and groundwater resources. A comparative evaluation along with the benefit-cost ratios of the existing and proposed farming systems is also presented.     

Interfacial tension between low pressure argon plasma and molten copper and iron

The interfacial tension between the molten metal and the surrounding plasma environment affects the circulation of molten metal in the weld pool, heat transfer, and the eventual structure and properties of the weld metal. Since the effect of plasma on the interfacial tension of molten metals is not known, interfacial tension values between low pressure argon plasma and pure copper and iron were measured. The variables studied were temperature and the intensity of plasma emission.     

Progress in deep-UV photoresists

Higher resolution can be achieved in lithography by decreasing the wavelength of the exposure source. However, resist material and their processing are also important when we move to a shorter wavelength lithography technology. This paper reviews the recent development and challenges of deep-UV photoresists and their processing technology.     

IEEE-PES Transmission and Distribution Conference and Exposition Call for Papers

Static network-related system voltage stability margin (VSM) depends on the availability of reactive power to support the transport of real power from sources to sinks. Based on this premise, the total VAr loss is minimized in the unified OPF framework considering real and reactive power controllers, and its effect on VSM is studied. Studies are conducted on a three-bus system, the IEEE 30-bus system, and a 191-bus Indian electric power system, and their results are reported.     

Protecting against key-exposure: strongly key-insulated encryption with optimal threshold

Key-insulated encryption schemes use a combination of key splitting and key evolution to protect against key exposure. Existing schemes, however scale poorly, having cost proportional to the number t of time periods that may be compromised by the adversary, and thus are practical only for small values of t. Yet in practice t might be large. This paper presents a strongly key-insulated encryption scheme with optimal threshold. In our scheme, t need not be known in advance and can be as large as one less than the total number of periods, yet the cost of the scheme is not impacted. This brings key-insulated encryption closer to practice. Our scheme is based on the Boneh-Franklin identity-based encryption (IBE) scheme [9], and exploits algebraic properties of the latter. Another contribution of this paper is to show that (not strongly) key-insulated encryption with optimal threshold and allowing random-access key updates (which our scheme and all others known allow) is equivalent to a restricted form of IBE. This means that the connection between key-insulated encryption and IBE is not accidental. Supported in part by NSF grants CCR-0098123, ANR-0129617 and CCR-0208842, and by an IBM Faculty Partnership Development Award. Supported in part by an NSF graduate fellowship.