A Smart Hyperthermia Nanofiber-Platform-Enabled Sustained Release of Doxorubicin and 17AAG for Synergistic Cancer Therapy

This study demonstrates the rational fabrication of a magnetic composite nanofiber mesh that can achieve mutual synergy of hyperthermia, chemotherapy, and thermo-molecularly targeted therapy for highly potent therapeutic effects. The nanofiber is composed of biodegradable poly(ε-caprolactone) with doxorubicin, magnetic nanoparticles, and 17-allylamino-17-demethoxygeldanamycin. The nanofiber exhibits distinct hyperthermia, owing to the presence of magnetic nanoparticles upon exposure of the mesh to an alternating magnetic field, which causes heat-induced cell killing as well as enhanced chemotherapeutic efficiency of doxorubicin. The effectiveness of hyperthermia is further enhanced through the inhibition of heat shock protein activity after hyperthermia by releasing the inhibitor 17-allylamino-17-demethoxygeldanamycin. These findings represent a smart nanofiber system for potent cancer therapy and may provide a new approach for the development of localized medication delivery.     

Performance of compression/absorption hybrid refrigeration cycle with propane/mineral oil combination

This paper discusses the feasibility of a vapor compression/absorption hybrid refrigeration cycle for energy saving and utilization of waste heat. The cycle employs propane as a natural refrigerant and a refrigeration oil as an absorbent. A prototype of the cycle is constructed, in which a compressor and an absorption unit are combined in series. The performance of the cycle is examined both theoretically and experimentally. Although the solubility of the propane with the oil is not enough as a working pair in the absorption unit, the theoretical calculation shows that the hybrid cycle has a potential to achieve a higher performance in comparison with a simple vapor compression cycle by using the waste heat. In the experiment, the prototype cycle is operated successfully and it is found that an improvement of an absorber is necessary to achieve the good performance close to the theoretical one. The application of an AHE (absorber heat exchanger) can reduce the heat input to a generator. Further examinations on some other combinations of refrigerant/refrigeration oil and additives are desirable.     

A 64-Mb DRAM with meshed power line

A 64-Mb dynamic RAM (DRAM) has been developed with a meshed power line (MPL) and a quasi-distributed sense-amplifier driver (qDSAD) scheme. It realizes high speed, t_RAS=50 ns (typical) at V_cc=3.3 V, and 16-b input/output (I/O). This MPL+qDSAD scheme can reduce sensing delay caused by the metal layer resistance. Furthermore, to suppress crosstalk noise, a V_SS shield peripheral layout scheme has been introduced, which also widens power line widths. This 64-Mb DRAM was fabricated with 0.4-μm CMOS technology using KrF excimer laser lithography. A newly developed memory cell structure, the tunnel-shaped stacked-capacitor cell (TSSC), was adapted to this 64-Mb DRAM     

Diffusion Bonded EDM Electrode with Micro Holes for Jetting Dielectric Liquid

This paper describes improvement of machining characteristics of electrical discharge machining of deep slots using a tool electrode which has micro holes for jetting dielectric liquid over the working surface. The tool electrode was made by the diffusion bonding of two copper plates, over an interface on which micro grooves for jetting the dielectric fluid were formed using electrolyte jet machining. In conventional machining, it is difficult to drill micro holes at the end of a slim electrode and circulate the dielectric fluid from the other end. Hence a solid tool electrode is used and periodically lifted up during machining to flush debris particles out of the discharge gap. Use of the newly developed tool electrode was found to shorten the processing time and improve machining accuracy significantly compared with the conventional solid tool electrode. Since the holes are micro, the outlet shapes are not replicated onto the bottom surface of the slot machined.     

Chemical Modification of Phage-Displayed Helix-Loop-Helix Peptides to Construct Kinase-Focused Libraries

Conformationally constrained peptides hold promise as molecular tools in chemical biology and as a new modality in drug discovery. The construction and screening of a target-focused library could be a promising approach for the generation of de novo ligands or inhibitors against target proteins. Here, we have prepared a protein kinase-focused library by chemically modifying helix-loop-helix (HLH) peptides displayed on phage and subsequently tethered to adenosine. The library was screened against aurora kinase A (AurA). The selected HLH peptide Bip - 3 retained the α-helical structure and bound to AurA with a K_D value of 13.7 μM. Bip - 3 and the adenosine-tethered peptide Bip - 3 - Adc provided IC₅₀ values of 103 μM and 7.7 μM, respectively, suggesting that Bip - 3 - Adc bivalently inhibited AurA. In addition, the selectivity of Bip - 3 - Adc to several protein kinases was tested, and was highest against AurA. These results demonstrate that chemical modification can enable the construction of a kinase-focused library of phage-displayed HLH peptides.     

Thermal properties of ethylene ionomers

The annealing effect of ethylene ionomers annealed at various temperatures and for various periods was studied by differential scanning calorimetry. Two endothermic melting peaks were observed for all the ethylene ionomers annealed. The melting peak at the lower temperature, which was assigned to bundlelike crystal owing to a Hoffman-Weeks relationship, shifted to a higher temperature with the annealing temperature and period, indicative of recrystallization. There is physical cross-linking consisting of ionic aggregates, such as multiplets and clusters in ethylene ionomers. The crystallization kinetics of ethylene ionomers was fundamentally similar, but different from that of low-density polyethylene. Crystallization and recrystallization suggested a mobile ethylene chain in both amorphous regions and ionic aggregates even in the presence of cross-linking.     

Time-series primitive static states for detailing work state and flow of human-operated work machine

This paper proposes a quantification method for a comprehensive work flow in construction work for describing work states in more detail on the basis of analyzing state transitions of primitive static states (PSS), which consist of 16 symbolic work states defined by using on-off state of the lever operations and joint loads for the manipulator and end-effector. On the basis of the state transition rules derived from a transition-condition analysis, practical state transitions (PST), which are common and frequent transitions in arbitrary construction work, are defined. PST can be classified into essential state transition (EST) or nonessential state transitions (NST). EST extracts common phases of work progress and estimates positional relations between a manipulator and an object. NST reveals wasted movements that degrade the efficiency and quality of work. To evaluate comprehensive work flows modeled by combining EST and NST, work-analysis experiments using our instrumented setup were conducted. Results indicate that all the PSS definitely changes on the basis of PST under various work conditions, and work analysis using EST and NST easily reveals work characteristics and untrained tasks related to wasted movements.     

Concentration of acetic acid in sulfite pulp evaporation drain by reverse osmosis

The evaporation drain of sulfite pulp spent liquor contains few volatile fatty acids, most of which is acetic acid. The main objective of this study is to recover acetic acid as the concentrated solution (about 4%), which could be used as a culture medium of the yeast. As acetic acid can easily pass through the cellulose acetate membrane, SP drains neutralized by NaOH, NH₄OH and Ca(OH)₂ were used as the feed solutions. In all cases, concentration by reverse osmosis was successfully carried out provided the appropriate pretreatment was employed. The recovery of acetic acid was 95.6, 90.5 and 98.2% for Na-, NH₄-, and Ca-drain, respectively. In addition, the recovered (permeated) water may be used as an industrial one.     

Gel-size dependence of temperature-induced microphase separation in weakly-charged polymer gels

The gel-size dependence of microphase separation in weakly-charged gels of N-isopropylacrylamide (NIPA) and 1-vinylimidazole (VI) copolymers has been investigated using swelling measurement, small-angle neutron scattering (SANS), and dynamic and static light scattering (DLS/SLS). It is known that weakly-charged polymer gels undergo microphase separation in a poor solvent as a result of competing interactions involving hydrophobic attraction versus electrostatic repulsion. The microphase separation is characterized by a scattering maximum in SANS intensity functions of which Bragg spacing, Λ, is around 20-30 nm. However, when gel size was reduced to the order of Λ, no microphase separation was observed. Instead, a typical scattering of isolated spherical particles was clearly observed. On the basis of the experimental evidence, we conclude that microphase separation has its own wavelength independent of gel size, and nanometer-order gels, i.e., nanogels, do not undergo microphase separation.     

Biocomposites Made from Short Abaca Fiber and Biodegradable Polyesters

Natural fiber‐reinforced biodegradable polyester composites were prepared from biodegradable polyesters and surface‐untreated or ‐treated abaca fibers (length ca. 5 mm) by melt mixing and subsequent injection molding. Poly(butylene succinate)(PBS), polyestercarbonate (PEC)/poly(lactic acid)(PLA) blend, and PLA were used as biodegradable polyesters. Esterifications using acetic anhydride and butyric anhydride, alkali treatment, and cyanoethylation were performed as surface treatments on the fiber. The flexural moduli of all the fiber‐reinforced composites increased with fiber content. The effect of the surface treatment on the flexural modulus of the fiber‐reinforced composites was not so pronounced. The flexural strength of PBS composites increased with fiber content, and esterification of the fiber by butyric anhydride gave the best result. For the PEC/PLA composites, flexural strength increased slightly with increased fiber content (0–20 wt.‐%) in the case of using untreated fiber, while it increased considerably in the case of using the fiber esterified by butyric anhydride. For the PLA composite, flexural strength did not increase with the fiber reinforcement. The result of soil‐burial tests showed that the composites using untreated fiber have a higher weight loss than both the neat resin and the composites made using acetylated fiber.

Flexural modulus of PBS composites as a function of fiber content.