Radiation detector made of a high-quality polycrystalline diamond

Radiation detector was made of a high-quality CVD polycrystalline diamond composed of frost column like structure diamond grains, and induced charge distribution spectra and drift velocities were measured by using alpha particles. As a result, the CVD polycrystalline achieved maximum induced charge of 83% of HP/HT type IIa diamond. Moreover, the CVD crystal had lower charge loss on electrons compared with the HP/HT type IIa diamond. Drift velocities of electrons and holes were v_e = 7.7 × 10⁴ and v_h = 7.3 × 10⁴cm/s at an electric field of 20 kV/cm, respectively. In addition, response function measurement for 14 MeV neutrons was carried out.     

Thermal shock resistance of flat plastic integrated circuit packages

Flat packages (FPs) were formed from epoxy molding compounds with various physical properties using a transfer molding machine. The compounds were prepared by changing kinds and amounts of additives and addition methods. The thermal shock test was carried out by the following procedures. The plastic package was soaked alternately in liquid nitrogen (?196°) and in liquid solder (200°) in the cycle of 140s. The median life to crack initiation was defined to be the cycles when half of the specimens exhibited crack initiation. According to linear fracture mechanics, the following expression was obtained relating the median life N, thermal stress σ_t, and strength σ_b; N = C/σ·(σ_b/σ_t)^m. We found the linear relation between logarithm of Nσ and logarithm of σ_b/σ_t for various packages, and estimated the values of C and m as 5 × 10⁴ MPa² and 5.5, respectively. The value of m was the same as that obtained for a dual-in-line package.     

Separation of Polyvinyl Chloride from Plastic Mixture by Froth Flotation after Surface Modification with Ozone

Selective modification by ozonation for the surface of polyvinyl chloride (PVC) was evaluated to separate PVC from the other plastics, polyethylene terephthalate (PET), polycarbonate (PC) and polymethyl methacrylate (PMMA), with almost the same density as PVC by the froth flotation process. Ozonation could selectively decrease the contact angles of flexible PVC from 87.5 degrees to 68.4 degrees and rigid PVC from 90.3 degrees to 66.9 degrees, whereas little decreases in the contact angle were observed for other plastics. This would be due to the replacement of the chloride group on the surface of PVC, into hydrophilic functional groups; carbonyl, carboxyl and ester group. The PVC was successfully separated from the other plastics by the froth flotation process after the selective surface modification by ozonation.     

Revealing microbial community structures in large- and small-scale activated sludge systems by barcoded pyrosequencing of 16S rRNA gene

The diversity of bacterial groups in activated sludge from large- and small-scale wastewater treatment plants was explored by barcoded pyrosequencing of 16S rRNA gene. Activated sludge samples (three small and 17 large scale) were collected from 12 wastewater treatment plants to clarify precise taxonomy and relative abundances. DNA was extracted, and amplified by 4 base barcoded 27f/519r primer set. The 454 Titanium (Roche) pyrosequences were obtained and analyses performed by Quantitative Insight Into Microbial Ecology (QIIME) with around 100,000 reads. Sequence statistics were computed, while constructing a phylogenetic tree and heatmap. Computed results explained total microbial diversity at phylum and class level and resolution was further extended to Operational Taxonomic Unit (OTU) based taxonomic assignment for investigating community distribution based on individual sample. Composition of sequence reads were compared and microbial community structures for large- and small-scale treatment plants were identified as major phyla (Proteobacteria and Bacteroidetes) and classes (Betaproteobacteria and Bacteroidetes). Also, family level breakdowns were explained and differences in family Nitrospiraceae and phylum Actinobacteria found at their species level were also illustrated. Thus, the pyrosequencing method provides high resolution insight into microbial community structures in activated sludge that might have been unnoticed with conventional approaches.     

Yield of OH radicals in water under heavy ion irradiation. Dependence on mass, specific energy, and elapsed time

Dependence of yields of OH （hydroxyl） radicals on the mass and specific energy of heavy ions and elapsed time after irradiation was investigated, to understand chemical reactions of aqueous solutions. The yields of irradiation products of phenol, super-linearly increased with the incident energy of He, C, and Ne ions ranging from 2 to 18 MeV/u. The yields of the OH radicals were estimated by analyzing the yields of the irradiation products of phenol. The yields of the OH radicals increased with the specific energy for each ion, but decreased both with the mass of each ion at the same specific energy and elapsed time after irradiation.     

Application of electron beam for the reduction of PCDD/F emission from municipal solid waste incinerators

The electron-beam technology was applied to reduce the emission of polychlorinated dibenzo-p-dioxins (PCDD) and polychlorinated dibenzofurans (PCDF) in a flue gas of 1000 m(3)N/h from the municipal solid waste incinerator (MSWI) at a temperature of 200 degrees C. More than 90% decomposition of PCDD/Fs was obtained using an electron accelerator at a dose of 14 kGy. The decomposition was initiated through reactions with OH radicals produced by the irradiation of flue gases, followed by oxidation such as the ring cleavage of the aromatic ring, the dissociation of ether bond, and dechlorination. The cost analysis estimated that the electron-beam system can cut the annualized cost by approximately 50% for the treatment of PCDD/Fs in a pre-dusted MSWI flue gas as compared with a bag-filter system when operating on electricity generated from an incineration. Electron-beam technology is an economically and technologically useful method for reducing PCDD/Fs in an incineration flue gas.     

Terephthalic acid synthesis at higher concentrations in high‐temperature liquid water. 2. Eliminating undesired byproducts

We synthesized terephthalic acid (TPA) from p‐xylene at an initial concentration above its solubility limit in high‐temperature liquid water (HTW). The nominal p‐xylene loading at the reaction conditions was 0.4 mol L^?1, which is the highest reported to date for generation of high TPA yields (>70 mol %) in HTW. The presence of two liquid phases during the reaction did not appear to accelerate the rate, unlike behavior reported for some other organic reactions done “on water” at lower temperatures. Adding oxygen gas in a large increment during synthesis produced a black liquid and a black solid byproduct, which is a previously undocumented problem. Adding oxygen in smaller increments prevented formation of the liquid and solid byproducts and also provided high selectivities (90 mol %) and yields (>70 mol %) of TPA. These results demonstrate the feasibility of HTW as a medium for TPA synthesis at p‐xylene concentrations even higher than its solubility limit. © 2009 American Institute of Chemical Engineers AIChE J, 2009     

Source identification of nitrous oxide on autotrophic partial nitrification in a granular sludge reactor

Emission of nitrous oxide (N₂O) during biological wastewater treatment is of growing concern since N₂O is a major stratospheric ozone-depleting substance and an important greenhouse gas. The emission of N₂O from a lab-scale granular sequencing batch reactor (SBR) for partial nitrification (PN) treating synthetic wastewater without organic carbon was therefore determined in this study, because PN process is known to produce more N₂O than conventional nitrification processes. The average N₂O emission rate from the SBR was 0.32 ± 0.17 mg-N L⁻¹ h⁻¹, corresponding to the average emission of N₂O of 0.8 ± 0.4% of the incoming nitrogen load (1.5 ± 0.8% of the converted NH₄⁺). Analysis of dynamic concentration profiles during one cycle of the SBR operation demonstrated that N₂O concentration in off-gas was the highest just after starting aeration whereas N₂O concentration in effluent was gradually increased in the initial 40 min of the aeration period and was decreased thereafter. Isotopomer analysis was conducted to identify the main N₂O production pathway in the reactor during one cycle. The hydroxylamine (NH₂OH) oxidation pathway accounted for 65% of the total N₂O production in the initial phase during one cycle, whereas contribution of the NO₂⁻ reduction pathway to N₂O production was comparable with that of the NH₂OH oxidation pathway in the latter phase. In addition, spatial distributions of bacteria and their activities in single microbial granules taken from the reactor were determined with microsensors and by in situ hybridization. Partial nitrification occurred mainly in the oxic surface layer of the granules and ammonia-oxidizing bacteria were abundant in this layer. N₂O production was also found mainly in the oxic surface layer. Based on these results, although N₂O was produced mainly via NH₂OH oxidation pathway in the autotrophic partial nitrification reactor, N₂O production mechanisms were complex and could involve multiple N₂O production pathways.     

Space charge field effect on light emitting from tetracene field-effect transistor under AC electric field

By applying square wave AC voltage to the Au source electrode of tetracene based field-effect transistor (FET), electroluminescence (EL) was obtained. The results suggest that electrons and holes were injected alternately from the source electrode and recombined each other, and lead to the EL. This type of EL was localized at the interface between the source electrode and tetracene, and enhanced periodically with two relaxation times in accordance with the applied AC voltage cycle. We modeled the carrier behavior in the FET and explained the decay of EL, taking into account the space charge field contribution. Finally, using an AC voltage superposed on DC bias voltage, it was shown that electron injection was prompted only by space charge field.     

Solid polymerization and supramolecular chirality formation of azobenzene substituted diacetylene Langmuir–Blodgett films

An azobenzene mesogen-substituted diacetylene (NADA) monolayer has been transferred onto the solid substrate by the traditional Langmuir–Blodgett (LB) method. Solid-state polymerization of NADA LB films can be sensitized in visible light region. In situ UV–vis absorption measurement enables us to study polymerization kinetics of NADA LB films. The polymerization process can be described as a first order rate equation and polymerization rate constants are characterized in detail. Furthermore, achiral NADA molecules can form chiral LB films through overcrowded packing of the azobenzene moiety.