High throughput blood plasma separation using a passive PMMA microfluidic device

Since plasma is rich in many biomarkers used in clinical diagnostic experiments, microscale blood plasma separation is a primitive step in most of microfluidic analytical chips. In this paper, a passive microfluidic device for on-chip blood plasma separation based on Zweifach–Fung effect and plasma skimming was designed and fabricated by hot embossing of microchannels on a PMMA substrate and thermal bonding process. Human blood was diluted in various times and injected into the device. The main novelty of the proposed microfluidic device is the design of diffuser-shaped daughter channels. Our results demonstrated that this design exerted a considerable positive influence on the separation efficiency of the passive separator device, and the separation efficiency of 66.6 % was achieved. The optimum purity efficiency of 70 % was achieved for 1:100 dilution times.     

Effect of heat treatment on foaming properties of ostrich (Struthio camelus) egg white proteins

The effect of heat-treatment on foaming properties of ostrich albumen was investigated. At pH 7.5, coagulation of ovotransferrin (OT) resulted in minimum foaming capacity (FC) and maximum foam density (FD). While both exposure of sulfhydryl groups of ovalbumin (OV) and OT-OV interactions improved FC at lower pH, neither of them had beneficial effect on FC at pH 9. At pH 9, FC and FD were mildly affected by heat-treatment because of less aggregation of OT, then FC decreased due to covalent aggregates composed of ovomucin and OV, but at higher temperatures, higher level of OV unfolding resulted in enhanced FC.     

Preparation of novel 2-(2-oxo-2H-chromen-4-yl)-3- arylthiazolidin-4-one derivatives using an efficient ionic liquid catalyst

An eco-friendly procedure for synthesis of 2-(2-oxo-2H-chromen-4-yl)-3-arylthiazolidin-4-one derivatives by three-component reaction of 2-oxo-2H-chromene-4-carbaldehydes, aromatic amines and thioglycolic acid, with tetramethylbutane-1,4-diammonium acetate as a low-cost ionic liquid catalyst under reflux condition is described. The use of an ionic liquid as a catalyst has the advantages of high yields, short reaction time and environmentally friendly reaction media.     

Production of surface-active sophorolipid biosurfactant and crude oil degradability by novel Rhodotorula mucilaginosa strain SKF2

Biosurfactants are produced by important types of microorganisms such as bacteria, yeast, and filamentous fungi and have been used in a variety of industries. Among the 15 crude oil-degrading fungi, the two molds and one yeast were identified by 18S rDNA sequences as Mucor circinelloides strain SKMC, Fusarium fujikuroi strain DB2, and Rhodotorula mucilaginosa strain SKF2. These strains were isolated from crude oil–contaminated soil, diesel oil–contaminated soil, and activated sludge in the Oil Refinery Plant in Isfahan, Iran, respectively. The yeast strain was identified as a novel crude oil–degrading and biosurfactant-producing fungi in the presence of (1% v/v) Iranian light crude oil in the minimal salt medium (MSM). The highest amount of the dry weight of produced biosurfactant was measured at 6.2 g L⁻¹. Chemical nature of produced biosurfactant was determined as a surface-active sophorolipid biosurfactant compound by thin-layer chromatography, Fourier transform infra-red spectroscopy, and gas chromatography–mass spectrometry (GC–MS) analysis. The residual hydrocarbons in the MSM were analyzed by GC–MS, and it was shown that octadecane and docosane were eliminated by this novel strain completely.     

Impact of oxygen concentration during the deposition of window layers on lowering the metastability effects in Cu(In,Ga)Se2/CBD Zn(S,O) based solar cell

The purpose of the present paper is to focus on the impact of oxygen gas partial pressure during the sputtering of i‐ZnO and ZnMgO on the transient behavior of Cu(In,Ga)Se₂ (CIGSe) based solar cells parameters when a CBD‐Zn(S,O) buffer layer is used. Based on electrical characterization of cells, it is observed that the effect of light soaking is different on J–V characteristics depending on whether oxygen is or is not present during the first deposition time of the i‐ZnO or ZnMgO layers. In fact, when cells are prepared with standard i‐ZnO, the efficiencies are very low and a pronounced transient behavior is observed. However, when the first 10 nm of i‐ZnO or ZnMgO is formed by sputtered layer without adding oxygen during the process, depending on the thickness of the buffer layer, the transient effects strongly decreases. It is then possible to get stable cells reaching efficiencies quite similar to the CdS reference cells, especially with ZnMgO, without any post‐treatments. Copyright © 2015 John Wiley & Sons, Ltd.     

Simulation,model‐reduction,and state estimation of a two‐component coagulation process

The issue of state estimation of an aggregation process through (1) using model reduction to obtain a tractable approximation of the governing dynamics and (2) designing a fast moving‐horizon estimator for the reduced‐order model is addressed. The method of moments is first used to reduce the governing integro‐differential equation down to a nonlinear ordinary differential equation. This reduced‐order model is then simulated for both batch and continuous processes and the results are shown to agree with constant Number Monte Carlo simulation results of the original model. Next, the states of the reduced order model are estimated in a moving horizon estimation approach. For this purpose, Carleman linearization is first employed and the nonlinear system is represented in a bilinear form. This representation lessens the computation burden of the estimation problem by allowing for analytical solution of the state variables as well as sensitivities with respect to decision variables. © 2016 American Institute of Chemical Engineers AIChE J, 62: 1557–1567, 2016     

Nanosilica Supported Dual Acidic Ionic Liquid as a Recyclable Catalyst for the Rapid and Green Synthesis of Polycyclic Phenolic Compounds

Generally ionic liquids have gained increasing attention in organic synthesis as catalyst and solvent. However, there are some drawbacks, including the difficulties in the product purification, ionic liquid recycling, and use of excess amounts of the expensive ionic liquid when the ionic liquid is used in the organic reactions. In addition, the high viscosity of ionic liquids can lead to mass transfer limitations in fast chemical reactions. These problems can be overcome by the use of supported ionic liquid phases. In this article, a simple, efficient and green method has been developed for the synthesis of bisphenolic antioxidants by the reaction of 2-tert-butyl-4-methylphenol and aldehydes in the presence of nanosilica supported dual acidic ionic liquid (NSSDAIL) as robust and reusable catalyst under solvent-free conditions. Three different NSSDAILs were synthesized and characterized using SEM, BET, IR, and XRD techniques. High yields of the products, short reaction times, use of a non corrosive, non toxic and reusable catalyst, and use of solvent-free condition are the worthwhile advantages of the current method.     

Thermal,mechanical, and corrosion resistance properties of vinyl ester/clay nanocomposites for the matrix of carbon fiber‐reinforced composites exposed to electron beam

Vinyl ester/clay nanocomposites with 1, 3, and 5% nanoclay contents were prepared. X‐ray diffractography patterns and Scanning Electron micrographs showed that nanocomposites with the exfoliated structure were formed. Thermogravimetric analysis, water absorption test, and Tafel polarization method, respectively, revealed the improvements in thermal resistance, water barrier properties, and corrosion resistance properties of the samples with an increase in the amount of the incorporated nanoclay. Tensile tests showed that nanoclay also enhanced the mechanical properties of the polymer, so that the tensile strength of the samples with 5% nanoclay was more than 3 times higher than tensile strength of pure vinyl ester samples. Overall, the best properties were observed for the samples containing 5% nanoclay. Pure vinyl ester and nanocomposite with 5% nanoclay content were exposed to the electron beam radiation and their mechanical properties improved up to 500 kGy irradiation dose. Finally, pure vinyl ester and vinyl ester/nanoclay (5%) matrixes were reinforced with carbon fiber and the effect of electron beam irradiation on their mechanical properties was examined. The tensile strength and the modulus of the samples initially increased after exposure to the radiation doses up to 500 kGy and then a decrease was observed as the irradiation dose rose to 1000 kGy. Moreover, nanoclay moderated the effect of the irradiation. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42393.     

Thermodynamic and experimental study of chemical bath deposition of Zn(S,O,OH) buffer layers in basic aqueous ammonia solutions. Cell results with electrodeposited CuIn(S,Se)2 absorbers

This paper presents a thermodynamic study of Chemical Bath Deposition (CBD) of zinc sulphide based films in aqueous ammonia solutions. The aim is a better understanding of ammonia and temperature effects on the deposition conditions and films composition. The formation of solid phases has been predicted by means of the precipitation conditions of ZnO, Zn(OH)₂ and ZnS as a function of temperature between 298 and 333 K. Films have been deposited according to calculated diagrams and preliminary results on solar cells based on electrodeposited CuIn(S,Se)₂ layers have been demonstrated. Composition and thickness of the films have been extracted to link the theoretical study with experiments.     

Photoactive Electrodes Incorporating Electrosprayed Bacterial Reaction Centers

Highly efficient light absorption and charge separation within the photosystem and reaction center (RC) complexes of photosynthetic plants and bacteria are of great interest for solar cell and photo detector applications, since they offer almost unity quantum yield and expected ultimate power conversion efficiencies of more than 18% and 12%, respectively. In addition, the charge separated states created by these protein complexes are very long lived compared to conventional semiconductor solar cells. In this work, a novel technique is presented for the deposition of photosynthetic protein complexes, by electrospraying RCs of Rhodobacter sphaeroides onto highly ordered pyrolytic graphite (HOPG) electrodes. Remarkably, it is shown that the RCs not only survive exposure to the high electric fields but also yield peak photocurrent densities of up to 7 μA cm^?2, which is equal to the highest value reported to date.