Analysis of phosphorus removal and anaerobic selector performance in a full-scale activated sludge process in Singapore.

This paper analyses the performance of the anaerobic selector (A/O process) in a full-scale activated sludge process receiving mostly industrial sewage discharge (> 60%) in Singapore. In addition to the sludge settleability, enhanced biological phosphorus removal (EBPR) was studied. The sludge volume index (SVI) reduced from 200 to 80 ml g(-1) and foaming was suppressed significantly, indicating the effectiveness of the anaerobic selector in improving sludge settleability. The phosphorus removal efficiency was 66%, and 7.5 mg HAc-COD was consumed per mg PO4(3-) -P removed. In the anaerobic compartment, 31% of the SCOD and 73% of the acetic acid in the settled sewage were removed with PO4(3-) -P release of 14.1 mg PO4(3-)-P l(-1). The linear correlation between PO4(3-) -P release in the anaerobic compartment and PO4(3-) -P uptake in the aerobic compartment indicates that there is about 0.8 mg PO4(3-) -P release in the anaerobic compartment per mg PO34(3-) -P uptake in the aerobic compartment. The fates of volatile fatty acids (VFAs) and its short chain acids (SCAs) in the process were studied and discussed.     

The effects of nonlocal impact ionization on the speed of avalanche photodiodes

The nonlocal enhancement in the velocities of charge carriers to ionization is shown to outweigh the opposing effects of dead space, increasing the avalanche speed of short avalanche photodiodes (APDs) over the predictions of a conventional local model which ignores both of these effects. The trends in the measured gain-bandwidth product of two short InAlAs APDs reported in the literature support this result. Relatively large speed benefits are predicted to result from further small reductions in the lengths of short multiplication regions.     

Impact of power control and lognormal shadowing on the mean transmit power of Bluetooth devices

This letter analyzes Bluetooth's power-control algorithm with a goal to study the mean transmit power required in the presence of lognormal shadowing. The following results are found. 1) A smaller power-control step size yields a lower mean transmit power. 2) When the standard deviations of lognormal shadowing are 3 and 6 dB, respectively, a Bluetooth device needs to consume 11.1 dB and 15.0 dB more in the transmit energy than the minimum one required in the absence of shadowing. 3) The transmit energy consumption varies by around 6 dB among Bluetooth devices as a result of the /spl plusmn/6 dB tolerance in the golden receive power range, which has a nominal size of 20 dB.     

Finite element piezothermoelasticity analysis and the active control of FGM plates with integrated piezoelectric sensors and actuators

 An efficient finite element model is presented for the static and dynamic piezothermoelastic analysis and control of FGM plates under temperature gradient environments using integrated piezoelectric sensor/actuator layers. The properties of an FGM plate are functionally graded in the thickness direction according to a volume fraction power law distribution. A constant displacement-cum-velocity feedback control algorithm that couples the direct and inverse piezoelectric effects is applied to provide active feedback control of the integrated FGM plate in a closed loop system. Numerical results for the static and dynamic control are presented for the FGM plate, which consists of zirconia and aluminum. The effects of the constituent volume fractions and the influence of feedback control gain on the static and dynamic responses of the FGM plates are examined. Received: 13 March 2002 / Accepted: 5 March 2003 The work described in this paper was supported by a grant awarded by the Research Grants Council of the Hong Kong Special Administrative Region, China (Project No. CityU 1024/01E).     

Stability of motor-unit force thresholds in the decerebrate cat

To further test the hypothesis that some fixed property of motoneurons determines their recruitment order, we quantified the variation in force threshold (FT) for motoneurons recruited in muscle stretch reflexes in the decerebrate cat. Motor axons supplying the medial gastrocnemius (MG) muscle were penetrated with micropipettes and physiological properties of the motoneuron and its muscle fibers, i.e., the motor unit, were measured. FT, defined as the amount of MG force produced when the isolated motor unit was recruited, was measured from 20 to 93 consecutive stretch trials for 29 motor units. Trials were selected for limited variation in base force and rate of rise of force, which have been shown to covary with FT, and in peak stretch force, which gives some index of motor-pool excitability. Under these restricted conditions, large variation in FT would have been inconsistent with the hypothesis. Analysis of the variation in FT employed the coefficient of variation (CV), because of the tendency for FT variance and mean to increase together. We found that CV was distributed with a median value of 10% and with only 2 of 29 units exceeding 36%. Some of this variation was associated with measurement error and with intertrial fluctuations in base, peak, and the rate of change of muscle force. CV was not significantly correlated with motor-unit axonal conduction velocity, contraction time, or force. In three cases FT was measured simultaneously from two motor units in the same stretch trials. Changes in recruitment order were rarely observed (5 of 121 stretch trials), even when FT ranges for units in a pair overlapped. We suggest that the large variation in recruitment threshold observed in some earlier studies resulted not from wide variation in the recruitment ranking of motoneurons within one muscle, but rather from variation in the relative activity of different pools of motoneurons. Our findings are consistent with the hypothesis that recruitment order is determined by some fixed property of alpha-motoneurons and/or by some unvarying combination of presynaptic inputs that fluctuate in parallel.     

A linkage map of human chromosome 21:43 PCR markers at average intervals of 2.5 cM

A genetic linkage map of human chromosome 21q (HC21q) containing 43 markers genotyped by the polymerase chain reaction in the CEPH pedigrees is presented. The markers placed on this map are highly polymorphic with an average heterozygosity of 61%. The average interval size of the markers localized at 1000:1 odds is 2.5 cM. The map has a total length of 65.5 cM, with male and female lengths of 47.7 and 83.3 cM, respectively. The genotypes used in the construction of this map were subjected to rigorous error checking, which is reflected in the shorter map length compared to previous maps; the estimated error rate in genotyping is less than 0.04%. As noted in previous linkage maps there is increased recombination in females on proximal HC 21q and in the male in a region near the telomere. This map of HC 21 represents a highly informative and dense meiotic linkage map and will be useful in linking disease phenotypes to loci on this chromosome.     

PHYSICS-BASED SIMULATION OF HIGH SPEED MACHINING

Computer simulation of high speed machining processes can provide a unique insight and reduce the number of design iterations required to advance and optimize the process. Predictive modeling of high speed machining of exotic materials has been hindered by the nonlinear behavior of this type of materials at extremely high strain, strain rate, and temperatures. This paper presents a physics-based modeling technology that includes the change in the material constitutive equation and the friction characterization at cutting speeds up to 400 m min^-1. The dependence of the accuracy of the predicted parameters, such as the chip formation on cutting forces, chip/tool/workpiece interface temperature, stress and strain distributions are also discussed. The fundamentals of metal cutting were utilized to understand the effect of parameter changes in regimes that are outside current empirical knowledge databases.     

Performance of combined cobalt—nickel—zirconia and HZSM-5 catalyst systems for carbon monoxide hydrogenation

The synthesis of hydrocarbons via hydrogenation of carbon monoxide was investigated over cobalt—nickel—zirconia catalysts of various compositions in combination with zeolite HZSM-5 in “mixed bed” and “follow bed” arrangements. These combinations resulted in the formation of aromatics in amounts as high as 30-35 wt% under relatively mild operating conditions (1 atm, 250–280°C). Although the olefinicity of C₂ and C₃ fractions in the product stream was higher in the mixed bed compared to the follow bed arrangement, the selectivities to aromatics were comparable in the two bed arrangements. The aromatic selectivity was found to be sensitive to operating conditions. The formation of aromatics was favored at high HZSM-5/metal catalyst ratios, low space velocities and high reaction temperatures. The product distributions obtained using various metal/zeolite bifunctional catalysts have been discussed.