Preparation of Laminin-apatite-polymer Composites Using Metastable Calcium Phosphate Solutions

A synthetic polymer with a laminin-apatite composite layer on its surface would be useful as a percutaneous device. The preparation of such a composite was attempted in the present study using poly（ ethylene terephthalate ） （PET） and polyethylene （PE） as the synthetic polymer. PET and PE plates and those pretreated with an oxygen plasma were alternately dipped in calcium and phosphate ion solutions, and then immersed in a metastable calcium phosphate solution supplemented with laminin （ LCP solution ）. The PET and PE plates pretreated with an oxygen plasma formed a uniform and continuous layer of a laminin-apatite composite on their surfaces. In contrast, the PET and PE plates that had not been pretreated with an oxygen plasma did not form a continuous layer of a laminin-apatite composite on their surfaces. The hydrophilic functional groups on the PET and PE surfaces introduced by the plasma treatment were responsible for the successful laminin-apatite coruposite coating.     

An automatic torque ripple compensation system for direct drive motors

A serious problem in motion control is the occurrence of torque ripple. Since a direct drive (DD) motor with a magnet rotor uses a rare-earth magnet, the torque ripple is more serious than that of conventional servomotors. This paper presents an auto-compensation of torque ripple using a software-implemented torque observer. The frequency and amplitude of torque ripple can be obtained in the controller by using the estimated torque from an observer, and the autonomous generation of a compensating current component for a torque ripple is possible. The proposed algorithm has been verified by experiments.     

A 0.1-μm delta-doped MOSFET fabricated with post-low-energyimplanting selective epitaxy

A simple fabrication technology for delta-doped MOSFETs, named post-low-energy implanting selective epitaxy (PLISE) is presented. The PLISE technology needs no additional photo-lithography mask, deposition step or etching step even for CMOS devices. The only additional step is growing undoped epitaxial channel layers by UHV-CVD after the channel implantation. With this technology, delta-doped NMOSFETs with 0.1-μm gate length were successfully fabricated. By optimizing the epi-layer thickness and the channel doping level, short-channel effects are suppressed enough to achieve 0.1-μm gate length. Moreover, the junction capacitance at zero bias is reduced by 50%     

Stabilization of bioethanol recovery with silicone rubber‐coated ethanol‐permselective silicalite membranes by controlling the pH of acidic feed solution

In order to produce highly concentrated bioethanol by pervaporation using an ethanol‐permselective silicalite membrane, techniques to suppress adsorption of succinic acid, which is a chief by‐product of ethanol fermentation and causes the deterioration in pervaporation performance, onto the silicalite crystals was investigated. The amount adsorbed increased as the pH of the aqueous succinic acid solution decreased. The pervaporation performance also decreased with decreasing pH when the ternary mixtures of ethanol/water/succinic acid were separated. Using silicalite membranes individually coated with two types of silicone rubber, pervaporation performance was significantly improved in the pH range of 5 to 7, when compared with that of non‐coated silicalite membranes in ternary mixtures of ethanol/water/succinic acid. Moreover, when using a silicalite membrane double‐coated with the two types of silicone rubber, pervaporation performance was stabilized at lower pH values. In the separation of bioethanol by pervaporation using the double‐coated silicalite membrane, removal of accumulated substances having an ultraviolet absorption maximum at approximately 260 nm from the fermentation broth proved to be vital for efficient pervaporation. Copyright © 2005 Society of Chemical Industry     

The temperature dependence of luminescence from a long-lasting phosphor exposed to ionizing radiation

The temperature dependence of luminescence from a long-lasting phosphor (LLP), SrAl₂O₄ : Eu²⁺,Dy³⁺, exposed to ionizing radiation has been measured to understand the LLP luminescence mechanism. Evaluation of the decay constants of the LLP exposed to -, β- or γ-rays at temperatures from 200 to 390 K showed that the decay constant is divided into four components ranging from 10⁻⁴ to 10⁻¹ s⁻¹ with activation energies of 0.02–0.35 eV.

Total luminous intensity from the LLP with changing irradiation temperature has its maximum value around the room temperature. Irradiation at elevated temperature (390 K) has the total luminescence pattern with monotonous decrease as temperature rises. As a result of evaluating the temperature dependence of luminescence, the luminescence mechanism is considered as follows:

Full-size image

 

Fiber-optic devices for local area network application

Recent developments on fiber-optic devices are reviewed from the local area network (LAN) application viewpoint. Future technical trends are also discussed, along with current research activities. In local area network systems, low device cost and easy maintenance or maintenance-free devices are especially required. Light sources and photodetectors suitable for the systems are described. InGaAsP/InP light emitting diodes can cover a broad application field, up to a gigabits per second super high-speed network region. Optical passive devices, which include branching couplers, switches and connectors, are mentioned as essential components. Compact transmitter/receiver module technology is a key factor in realizing optical-fiber local area network systems. An example of 200-Mbit/s transmitter/receiver module is reported.     

Performance prediction of a hybrid‐excitation synchronous machine with axially arranged excitation poles and permanent‐magnet poles

This paper presents a method of predicting the steady‐state performance of a new hybrid‐excitation synchronous machine (HESM) theoretically. The field pole of this HESM is axially divided into two parts; one is an excitation part and the other a permanent‐magnet (PM) part. A nonlinear equivalent circuit, which can include the saliency of the rotor and the magnetic saturation due to the iron core, is derived. Based on this equivalent circuit, the steady‐state performance of the HESM is calculated, and the results are confirmed through experiments. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 150(2): 43–49, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20033