Combustion synthesis of AlN doped with carbon and oxygen

Carbon-and-oxygen-doped AlN specimens were prepared by combustion synthesis using Al, graphite, and AlN. Graphite addition changed the product color from white to blue. By XRD, the lattice constant increased slightly with increasing carbon content. Blue AlN powder was synthesized with a molar ratio of the diluent AlN of 0.2-0.5 with a fixed graphite content of 0.05. At an AlN molar ratio exceeding 0.6, carbon was not successfully incorporated due to the lower reaction temperature. Calcination at 800°C in air removed residual graphite without changing the crystal structure or product color. Oxygen, nitrogen, and carbon analyses revealed that blue AlN powders contained 0.45-0.54 mass% carbon and 1.4-1.6 mass% oxygen, while the undoped AlN contained 0.021 mass% carbon and 0.94 mass% oxygen. The origin of the white-to-blue color change was investigated via reflection measurements. Blue AlN exhibits an absorption peak at 634 nm (1.96 eV). From first-principles electronic structure calculations, the C-doped AlN and carbon-and-oxygen-doped AlN with a 1:1 ratio could be classified as p-type, whereas the O-doped AlN and 1:3 carbon-and-oxygen-doped AlN were n-type. One reason for the absorption peak at 634 nm may be a transition from the conduction band to an upper unoccupied state. These results suggest the possible control of optical and electronic properties of AlN via carbon-and-oxygen doping.     

Oxidation of doped europium in BaMgAl10O17 by annealing studied by x‐ray‐absorption fine‐structure measurements

Abstract— We studied the influence of annealing in air on doped europium in BaMgAl₁₀O₁₇ by performing x‐ray absorption fine‐structure measurements. We determined the oxidation of doped divalent europium by annealing in air at over 500°C. The interatomic distance between the europium and the surrounding oxygen atoms was compressed by oxidation. It also appears that the oxidation process of europium is determined by the diffusion of oxygen into BaMgAl₁₀O₁₇.     

Superconductivity in SrTa2S5

A strontium tantalum sulfide, SrTa₂S₅, has a hexagonal structure with lattice constants of a =3.32 and c=24.1 Å. With decreasing temperature the electrical resistivity decreases monotonically and exhibits an abrupt superconducting transition at 3.16 K (midpoint). The diamagnetic susceptibility is observed below T_c. The magnetic susceptibility is nearly independent of temperature above T_c and shows Pauli paramagnetism.     

Facile optical resolution of amino acid esters via hydrolysis by an industrial enzyme in organic solvents

Racemic amino acid esters were optically resolved via hydrolysis in organic solvents by the catalysis of an industrial alkaline protease, “Alcalase”. The products which were composed mainly of L-amino acids were insoluble and easily separated by filtration. The activity of the enzyme and enantiomeric excess of the products were significantly dependent on the nature of solvent and the water content in the reaction media. Generally, high values of enantiomeric excess were obtained at low water contents. Many natural and unnatural amino acids were resolved by this method.     

A 10 bit 20 MS/s 3 V supply CMOS A/D converter

A 10 bit CMOS A/D converter with 3 V power supply has been developed for being integrated into system VLSI's. In this A/D converter, redundant binary encoders named “twin encoders” enhance tolerance to substrate noise, together with employing differential amplifiers in comparators. The bias circuit using a replica of the amplifier is developed for biasing differential comparators with 3 V power supply. Subranging architecture along with a multilevel tree decoding structure improves dynamic performance of the ADC at 3 V power supply. The A/D converter is fabricated in double-polysilicon, double-metal, 0.8 μm CMOS technology. The experimental results show that the ADC operates at 20 MS/s and the twin encoders suppress the influence of substrate noise effectively. This ADC has a single power supply of 3 V, and dissipates 135 mW at 20 MS/s operation     

Ring hydrogenation of naphthalene and 1-naphthol over supported metal catalysts in supercritical carbon dioxide solvent

Catalytic ring hydrogenations of naphthalene and 1-naphthol were studied over several supported metal catalysts in supercritical carbon dioxide solvent at low temperature. Higher concentration of hydrogen in supercritical carbon dioxide and lower reaction temperature were responsible for higher catalyst activity and selectivities to the desired partial ring hydrogenated products as compared with those observed in organic solvent for the same catalyst.     

Efficient usage of highly dispersed Pt on carbon nanotubes for electrode catalysts of polymer electrolyte fuel cells

A Pt-deposited carbon nanotube (CNT) shows higher performance than a commercial Pt-deposited carbon black (CB) with reducing 60% Pt load per electrode area in polymer electrolyte fuel cells (PEFCs) below 500 mA/cm². K₂PtCl₄ and H₂PtCl₆·6(H₂O) are used for the Pt deposition onto multi-walled CNTs (MWCNTs), which are produced by the catalytic decomposition of hydrocarbons. The electric power densities produced using the Pt/CNT electrodes are greater than that of the Pt/CB by a factor of two to four on the basis of the Pt load per power. CNTs are thus found to be a good support of Pt particles for PEFC electrodes. TEM images show 2–4-nm Pt nanoparticles dispersed on the CNT surfaces. These high performances are considered to be due to the efficient formation of the triple-phase boundaries of gas–electrode–electrolyte. The mechanisms of Pt deposition are discussed for these Pt-deposited CNTs.     

Effect of pressure on phase transition and morphology of bulk poly(trans-1,4-butadiene)

The effect of pressure on the melting, solid-solid transition, and crystallization of poly(trans-1,4-butadiene) (PTBD) was investigated using the pressure range of 1–3000 kg/cm². D.t.a. measurements showed that, the melting and transition temperatures increase with increasing pressure, whose pressure coefficients are 38°C per 1000 kg/cm² and 22°C per 1000 kg/cm², respectively. These values were in fairly close agreement with those calculated from the Clausius-Clapeyron equation. Morphological studies using electron microscope and small-angle X-ray scattering method revealed that, the samples crystallized with relatively small supercoolings under normal or high pressure, are formed of distinct lamellae 400–800 Å thick. The lamellar thickness was inappreciably dependent on crystallization pressure. The significant effect of pressure on crystallization was recognized in a tendency of the crystallinity to increase, with increasing crystallization pressure. This pressure effect was explained by the mechanism that, the increased pressure might make the packing of molecular chains in liquid, more dense and that the secondary crystallization might be accelerated, to increase the lateral dimensions of lamellae.     

Preparation and dielectric properties of polycrystalline films with dense nano-structured BaTiO3 by chemical vapor deposition using inductively coupled plasma

To clarify the dielectric properties of BaTiO₃ with nanometer size region, it is necessary to fabricate the dense structure composed of BaTiO₃ nanoparticles. In the present study, BaTiO₃ nanoparticles were directly deposited on Pt/Al₂O₃/SiO₂/Si substrate by introducing Ba(DPM)₂ and Ti(OiPr)₄ into an inductively coupled plasma (ICP). The optimal condition for preparing dense structure of BaTiO₃ nanoparticles was investigated by changing the substrate temperature. Single phase BaTiO₃ of perovskite structure was obtained at the substrate temperatures between 773 and 1173 K. The dense structure of BaTiO₃ nanoparticles with particle sizes of about 30 nm was successfully obtained at the substrate temperature of 773 K. At the substrate temperature>873 K, the deposited nanoparticles sintered to be the columnar structure. The ε_r and tan δ of the BaTiO₃ nanoparticles were estimated to be 285 and 6.6%, respectively (1 kHz and 100 mV). The phase of the BaTiO₃ nanoparticles were found to be paraelectric by the measurement of C-V curves. The breakdown field of the dense structure of BaTiO₃ nanoparticles was estimated to be 649 kV/cm according to I-V curves. These features are favorable for applying the structure to the dielectric layer of multilayer capacitors.