Preparation of Mn2+-Cu+ co-doped P2O5–ZnO–Al2O3 glasses and their red fluorescence properties

To make a Mn²⁺-doped red glass phosphor that can be excited with ultraviolet (UV) light of light-emitting diodes (LEDs), 60P₂O₅-35ZnO-5Al₂O₃-8MnO-xCu₂O glasses (x = 0-1.00) were prepared by a melt-quenching method at 1200-1400°C for 30-180 minutes in atmospheric air, and the redox of Mn and Cu as well as fluorescence properties were investigated. The Mn²⁺ ion was not reduced and oxidized in the melting, quenching, and annealing processes. The valence of Cu in the glasses changed in the order of 0, 1+, and 2+ with the increase in the amount of Cu₂O and in the melting temperature and time. In this study, a 60P₂O₅-35ZnO-5Al₂O₃-8MnO-0.10Cu₂O glass melted at 1250°C for 90 minutes, having the highest Cu⁺ concentration, showed the strongest Mn²⁺ red fluorescence under the UV light at 275 nm. This strong Mn²⁺ red fluorescence has been caused by the energy transfer from excited Cu⁺ ions to Mn²⁺ ions.     

Unperturbed dimension of poly(4-acetoxystyrene) measured in good and theta solvents

In order to obtain the additional data concerning the unperturbed dimension of poly-4-substituted styrene, light scattering measurements are performed on the twenty-two fractions with molecular weight of (0.91–352)·10⁴ of poly(4-acetoxystyrene) in dioxan at 25°C, from which the molecular weight obtained was found easily to be evaluated with the gel permeation chromatography using THF. Phase separation experiments for this polymer indicate that the theta state is attained in isopropyl acetate at 19.7°C and butyl acetate at 26.8°C. By making viscosity measurements at that state, the value of K_Θ is directly evaluated as 5.4·10^?4 dl g^?1. The limiting viscosity number is also obtained in good solvents, THF and dioxan, at 25°C and constants of the Mark-Houwink-Sakurada equation in each solvent are determined. Further, approximately the same K_Θ as above is obtained from these data with the Stockmayer-Fixman plot. The calculated value of steric factor, 2.37, on this polymer may be plausible, compared with those of polyvinylaromatic derivatives.     

External Synchronization of 160-GHz Optical Beat Signal by Optical Phase-Locked Loop Technique

We have synchronized a 160-GHz optical beat signal with a 40-GHz reference optical pulse train by using an optical phase-locked loop (OPLL). The OPLL consists of an optical beat signal source, comprising a pair of three-electrode distributed feedback laser diodes that works as a voltage controlled oscillator, and an all-optical phase detector based on the two-photon absorption in a silicon avalanche photodiode. Phase-locking operation is confirmed through phase-error measurement and cross-correlation trace measurement. The residual timing jitter of the 160-GHz optical beat signal relative to the reference pulse train, in the bandwidth of 80 MHz, is measured to be as small as 126 fs     

Analytical studies of four-inch pipe whip tests under BWR LOCA conditions

The purpose of pipe rupture studies in JAERI is to perform model tests on pipe whip, restraint behavior, jet impingement and jet thrust force, and to establish a computational method for analyzing these phenomena. This report presents the analytical results of 4-inch pipe whip tests under BWR LOCA conditions.Dynamic response analyses were performed using the general-purpose finite element program ADINA. The test pipe was modelled by straight beam elements and the four restraints were modelled by a single truss element. The analytical results were compared with the experimental results. Impact time and maximum total restraint force showed good agreement with experimental results. On the other hand, pipe strain and pipe deflection could not be predicted so well. The reason for this is that the sliding of the restraint during the pipe whip movement cannot be considered in the analyses.     

The 100 G capturing robot - too fast to see

This paper discusses the capturing robot with the maximum acceleration of 100 G in design specification. We aim find the combination of the arm with a mass of 0.1 kg and the spring capable of producing the initial compressed force of 100 N, in order to achieve the 100 G. To reduce the total capturing time, we propose an arm/gripper coupling mechanism where the spring energy initially accumulated in the arm is transferred to the kinetic energy of the arm and continuously to the kinetic energy for closing the gripper at the capturing point without any time lag. The experimental results show the maximum acceleration of 91 G and the capturing time of 25 ms were achieved. Experiments on capturing a dropping ball were also executed with the assistance of the 1 ms-vision.     

A reconfigurable VLSI-based double-lens tracking camera

Watching and tracking an object while seeing a much wider view is one of advantages of the eye system. We proposed and developed a tracking camera system that mimics the eyes by using double-lens modules. In the system, a wide view is captured through the wide-lens module, while the target in it is tracked and magnified through the telescopic lens module. Electronic circuits for tracking control are implemented onto the reconfigurable VLSI or FPGA in order to embed the parallelism in the tracking algorithm into the hardware. A successfully developed FPGA-based prototype performs high-speed tracking at the video-rate. This work was present in part at the 12th International Symposium on Artificial Life and Robotics, Oita, Japan, January 25–27, 2007     

Thermal expansion behavior of various aromatic polyimides

The thermal expansion behavior for various aromatic polymides was investigated. Usally polymers, including polyimides, have high thermal expansion coefficients (3–6 × 10^?5 K^?1), compared with metals and ceramics. However, there are some polyimides which have very low thermal expansion coefficients below 1 × 10^?5 K^?1. This property was observed for the polymides obtained from pyromellitic dianhydride or 3,3′ 4,4′-biphenyltetracarboxylic dianhydride and aromatic diamines which were constituted of only benzene rings fused at para positions. It was proposed that their low thermal expansion coefficient related to the linearity in their polymer molecular skeltons.     

Spatial Organization of the Brazilian States with Respect to Human Migration

"Multidimensional scaling technique was applied to the Brazilian migration matrix in order to identify the functional regions of the nation, using the 1970 census data for males. The results obtained from three types of proximity matrices confirmed the key roles of Minas Gerais and Mato Grosso as the core states in addition to Rio de Janeiro and Sao Paulo. Substantial circulation of migrants among the core states runs counter to the popular notion about the Northeastern states as the major source of labor in Rio de Janeiro and Sao Paulo. The Northeast [was] found to consist of three groups of states: Maranhao, Piaui and Ceara showed a stable clustering, but peripherally located, in all configurations; and, the other two groups failed to form persistent regions across configurations. Though limited in scope, the observed attraction of Espirito Santo and Goias violated the widely held negative effect of distance and deserves further investigation."     

Siliconizing of molybdenum plate using Si2Cl6 and some of its properties

Molybdenum plate was siliconized using Si₂Cl₆ as a silicon source, and the siliconizing conditions and some of its properties were examined. The siliconizing of the molybdenum plate began by the deposition here and there of island-like MoSi₂ deposits 4 to 6m thick in the initial stage (after 10 min induction time), and then coalescence of the deposits proceeded to form a uniform MoSi₂ layer all over the molybdenum plate after 30 min siliconizing time. The weight decrease of the siliconized plate by anodic dissolution in 0.2 M sulphuric acid reduced exponentially with increasing thickness of the MOSi₂ layer, and no weight decrease was observed at all above 16m thickness. The sea water corrosion and sea sand abrasion resistivities of the siliconized molybdenum plate increased with increasing siliconizing temperature and Si₂Cl₆ flow rate.