State of polarization changes: Classification and measurement

We propose a standardization procedure that provides a convenient, quantitative and reproducible laboratory-based method for measuring the state of polarization (SOP) fluctuations produced by polarization varying devices. This method is based on the SOP distributions generated by commercial polarization scramblers. We show that these devices generate distributions of the maximum change of the SOP (in a given sample time) that follow Rayleigh statistics, which scale linearly with scrambling frequency and the sample time. We use this procedure to measure the SOP fluctuations in a short length of coiled fiber subject to mechanical perturbations.     

蜕变——中国气象局华风影视大楼

华风气象影视大楼总面积4万平方米，根据空间功能不同分为办公大楼和商务写字楼两部分，办公大楼是集演播室、制作机房、办公室为一体的九层综合性建筑。设计师杨宇在刚接触到这个项目的时候，面对的是一个既成事实的建筑。     

Nonlinearity analysis and optimization of HBTs for optical mixer designs

Two types of photo heterojunction bipolar transistor (HBT) to directly down-convert optical signals to electronic signals have been reported in the literature: a conventional photo-HBT in which light penetrates through the area of the base-collector junction and an HBT where light shines through the base-collector edge for higher conversion efficiency. Although the performance in relation to bias conditions has been published, the detailed analyses for identifying the parameters and bias conditions that provide optimum direct down-conversion have not been examined. This paper provides a full explanation of the operation of the down-conversion for both HBT configurations based on low-frequency analyses. Such information is useful for both understanding the nonlinear mechanisms involved and designing for maximum efficiency. In addition, a new circuit has been developed from the basic HBT down-conversion circuit that provides improved performance.     

Radiometric sensor for temperature control of food processing

This paper describes a novel planar antenna sensor created for the purpose of noninvasive temperature measurements using microwave radiometry. In order to improve radiometric measurements in industrial applications, a new generation of sensors is introduced, composed of a metallic sheet. Simulations based upon the method of moments is used both to design and to determine their electromagnetic performances. This paper also describes a radiometric device using these sensors to measure and control the temperature of food products during deep freezing processes. The results and discussions are presented.     

TEM Studies of High Temperature Corrosion Behaviour of TiAl Intermetallics with Surface Modifications

The oxidation/sulphidation behaviour of a Ti‐46.7Al‐1.9W‐0.5Si alloy with a TiAl₃ diffusion coating was studied in an environment of H₂/H₂S/H₂O at 850^oC. The kinetic results demonstrate that the TiAl₃ coating significantly increased the high temperature corrosion resistance of Ti‐46.7Al‐1.9W‐0.5Si. The SEM, EDX, XRD and TEM analysis reveals that the formation of an Al₂O₃ scale on the surface of the TiAl₃‐coated sample was responsible for the enhancement of the corroison resistance. The Ti‐46.7Al‐1.9W‐0.5Si alloy was also modified by Nb ion implantation. The Nb ion implanted and as received sampels were subjected to cyclic oxidation in an open air at 800^oC. The Nb ion implantation not only increased the oxidation resistance but also substantially improved the adhesion of scale to the substrate.     

Synthesis of Rice Processing Plants. I. Development of Simplified Models

This article, the first of three articles on the synthesis of rice processing plants, focuses on the development of simplified mathematical models necessary for use in optimizing rice processing plants. The second concentrates on the optimal synthesis of a rice plant and the third on the sensitivity of the optimization to uncertainty in model parameters. Existing models for rice processing unit operations are not suitable for flowsheet optimization and new models need to be developed to overcome numerical difficulties that occur in optimization applications, specifically in mixed integer nonlinear programming (MINLP) applications. Simplified models of the drying, cooling, and tempering units are developed. In addition head rice yield models, used as a quality indicator, energy consumption, and economic models were also developed. Naturally, the new models exhibit some mismatch with respect to the existing models from which they were developed. However, a sensitivity analysis, presented in Part III, has shown that the optimal flowsheet structure was not sensitive to a lack of fit between the simplified and complex models. The simplified models were found adequate to be appropriate for use at the synthesis stage.     

Development of crumb rubber reinforced bituminous binder under laboratory conditions

Bituminous binders are widely used in the construction of flexible pavements. However, in some applications, the performance of conventional binders is not considered to be satisfactory. Reinforcing these binders with selected polymers prevents premature failure of a pavement by improving the properties of the binder. Another source of reinforcement comes from crumb (ground) rubber produced from waste tyres. After they have been worn-out during their limited service life, millions of used tyres are discarded every year and are hauled to a dump. The fatigue resistance at temperatures below normal service temperatures (25°C), one of the key engineering properties of crumb rubber reinforced binders, has been found to be lower than that of neat binders. This paper is concerned with the development of a rubber reinforced binder. It was shown that the binder has the potential to be used as an all-weather wearing course in flexible roads, whilst at the same time recycling a considerable amount of waste rubber.     

Solutions to a combined problem of excessive hydrogen sulfide in biogas and struvite scaling.

The Woodman Point Wastewater Treatment Plant (WWTP) in Western Australia has experienced two separate problems causing avoidable maintenance costs: the build-up of massive struvite (MgNH4PO4. 6H2O) scaling downstream of the anaerobic digester and the formation of hydrogen sulfide (H2S) levels in the digester gas to levels that compromised gas engine operation and caused high operating costs on the gas scrubber. As both problems hang together with a chemical imbalance in the anaerobic digester, we decided to investigate whether both problems could be (feasibly and economically) addressed by a common solution (such as dosing of iron solutions to precipitate both sulfide and phosphate), or by using separate approaches. Laboratory results showed that, the hydrogen sulfide emission in digesters could be effectively and economically controlled by the addition of iron dosing. Slightly higher than the theoretical value of 1.5 mol of FeCl3 was required to precipitate 1 mol of dissolved sulfide inside the digester. Due to the high concentration of PO4(3-) in the digested sludge liquor, significantly higher iron is required for struvite precipitation. Iron dosing did not appear an economic solution for struvite control via iron phosphate formation. By taking advantage of the natural tendency of struvite formation in the digester liquid, it is possible to reduce the risk of struvite precipitation in and around the sludge-dewatering centrifuge by increasing the pH to precipitate struvite out before passing through the centrifuge. However, as the Mg2+/PO4(3-) molar ratio in digested sludge was low, by increasing the pH alone (using NaOH) the precipitation of PO4(3-) was limited by the amount of cations (Ca2+ and Mg2+) available in the sludge. Although this would reduce struvite precipitation in the centrifuge, it could not significantly reduce PO4(3-) recycling back to the plant. For long-term operation, maximum PO4(3-) reduction should be the ultimate aim to minimise PO4(3-) accumulation in the plant. Magnesium hydroxide liquid (MHL) was found to be the most cost-effective chemical to achieve this goal. It enhanced struvite precipitation from both, digested sludge and centrate to the point where more than 95% PO4(3-) reduction in the digested sludge was achieved.     

Wear and Creep Characteristics of a Carbon‐Derived Si3N4/SiC Micro/Nanocomposite

In the presented work some properties of a recently developed Si₃N₄/SiC micro/nanocomposite have been investigated. The material was tested using a pin on disc configuration. Under unlubricated sliding conditions using Si₃N₄ pin at 50 % humidity, the friction coefficient was in the range of 0,6 ‐ 0,7. The reduction of humidity resulted in a lower coefficient of friction, in vacuum the coefficient of friction had a value of about 0,6. The wear resistance in vacuum was significantly lower then that in air. The wear patterns on the Si₃N₄+SiC disc revealed that mechanical fracture was the wear controlling mechanism. Creep tests were realized in four point bending configuration in the temperature interval 1200‐1400 °C at stresses 50,100 and 150 MPa and the minimal creep deformation rate was established for each stress level. The activation energy, established from the minimal creep deformation had a value of about 360 kJ/mol and the stress exponent values were in the range of 0.8‐1.28. From the achieved stress exponents it can be assumed that under the studied load/temperature conditions the diffusion creep was the most probable creep controlling mechanism.