Most of the commonly used hydrological models do not account for the actual evapotranspiration (ETa) as a key contributor to water loss in semi-arid/arid regions. In this study, the HEC-HMS (Hydrologic Engineering Center Hydrologic Modeling System) model was calibrated, modified, and its performance in simulating runoff resulting from short-duration rainfall events was evaluated. The model modifications included integrating spatially distributed ETa, calculated using the surface energy balance system (SEBS), into the model. Evaluating the model’s performance in simulating runoff showed that the default HEC-HMS model underestimated the runoff with root mean squared error (RMSE) of 0.14 m3/s (R2?=?0.92) while incorporating SEBS ETa into the model reduced RMSE to 0.01 m3/s (R2?=?0.99). The integration of HECHMS and SEBS resulted in smaller and more realistic latent heat flux estimates translated into a lower water loss rate and a higher magnitude of runoff simulated by the HECHMS model. The difference between runoff simulations using the default and modified model translated into an average of 95,000 m3 runoff per rainfall event (equal to seasonal water requirement of ten-hectare winter wheat) that could be planned and triggered for agricultural purposes, flood harvesting, and groundwater recharge in the region. The effect of ETa on the simulated runoff volume is expected to be more pronounced during high evaporative demand periods, longer rainfall events, and larger catchments. The outcome of this study signifies the importance of implementing accurate estimates of evapotranspiration into a hydrological model.
Theoretical Foundations of Chemical Engineering - Thin dense Pd composite membrane was prepared via electroless plating method. Pd nanoparticles embedded polyethylene glycol (PEG) was used in... 相似文献
The Nickel base Superalloys are the most famous complicated and useable of Superalloys to make hot zone components of the gas turbines. The complicated dimensional tolerances, specially at the root of the blade show importance of grinding processes at the production of blades root. The prediction of the effect of machining parameters on the soundness of component surface strengthening for reaching to a suitable surface finishing and avoiding from crack formation at the work part during machining operation often is not easy and feasible so needs to more industrial investigation.This research is about frame 5 blade designed by GE and made from Superalloy IN738LC has been investigated. The formation of a plastically deformed and heat affected zone during grinding of Superalloy IN738LC with a high depth of cut but slow work speed (creep feed grinding) was investigated. Parameters such as work speed, depth of cut and radial dressing speed have been considered as variables and their effects have been studied. During experimental performed, the voltage and current of motor measured and power and special energy calculated.Some samples heat-treated (of the 1176℃ for 1 hr under neutral argon gas and cooling rate of 15℃/min up to 537℃ and then air cooling) to study grains recrystallization. Other samples have been created from the roots of blades and then coated by Nickel to measure boundary layer micro-hardness. The results show that increasing work speed leads to increasing the use power. Increasing the depth of cut, by increasing material removal rate, and the radial dressing speed, by decreasing power, lead to decreasing special energy. The temperature created by grinding lead to decreasing plastic deformation and boundary layer formation. When the radial dressing speed changes from 1 to 0.6μm/rev and other parameters are kept unchanged the roughness of surface increases and the special energy decreases. Sufficient dressing is very essential in limiting the width of the molten zone to few micrometers. As a result, it was found that local melting at contact spots to be a rather common mechanism during grinding of superalloys, lead to so-called white layers which can easily be observed on metallographic cross sections. 相似文献
A model for the computational cost of the finite-difference time-domain (FDTD) method irrespective of implementation details or the application domain is given. The model is used to formalize the problem of optimal distribution of computational load to an arbitrary set of resources across a heterogeneous cluster. We show that the problem can be formulated as a minimax optimization problem and derive analytic lower bounds for the computational cost. The work provides insight into optimal design of FDTD parallel software. Our formulation of the load distribution problem takes simultaneously into account the computational and communication costs. We demonstrate that significant performance gains, as much as 75%, can be achieved by proper load distribution. 相似文献
Optoelectronic tweezers (OET) are a powerful light-based technique for the manipulation of micro- and nanoscopic particles. In addition to an optically patterned dielectrophoresis (DEP) force, other light-induced electrokinetic and thermal effects occur in the OET device. In this paper, we present a comprehensive theoretical and experimental investigation of various fluidic, optical, and electrical effects present during OET operation. These effects include DEP, light-induced ac electroosmosis, electrothermal flow, and buoyancy-driven flow. We present finite-element modeling of these effects to establish the dominant mode for a given set of device parameters and bias conditions. These results are confirmed experimentally and present a comprehensive outline of the operational regimes of the OET device. 相似文献
There have been few experience reports from industry on how Model-Driven Engineering (MDE) is applied and what the benefits are. This paper summarizes the experiences of three large industrial participants in a European research project with the objective of developing techniques and tools for applying MDE on the development of large and complex software systems. The participants had varying degrees of previous experience with MDE. They found MDE to be particularly useful for providing abstractions of complex systems at multiple levels or from different viewpoints, for the development of domain-specific models that facilitate communication with non-technical experts, for the purposes of simulation and testing, and for the consumption of models for analysis, such as performance-related decision support and system design improvements. From the industrial perspective, a methodology is considered to be useful and cost-efficient if it is possible to reuse solutions in multiple projects or products. However, developing reusable solutions required extra effort and sometimes had a negative impact on the performance of tools. While the companies identified several benefits of MDE, merging different tools with one another in a seamless development environment required several transformations, which increased the required implementation effort and complexity. Additionally, user-friendliness of tools and the provision of features for managing models of complex systems were identified as crucial for a wider industrial adoption of MDE. 相似文献
Bulletin of Engineering Geology and the Environment - In this study, a new predictor parameter (NPP), which is based on the product of uniaxial compressive strength (UCS) and Mohs hardness (MH),... 相似文献
The successful clinical application of bone tissue engineering requires customized implants based on the receiver’s bone anatomy and defect characteristics. Three-dimensional (3D) printing in small animal orthopedics has recently emerged as a valuable approach in fabricating individualized implants for receiver-specific needs. In veterinary medicine, because of the wide range of dimensions and anatomical variances, receiver-specific diagnosis and therapy are even more critical. The ability to generate 3D anatomical models and customize orthopedic instruments, implants, and scaffolds are advantages of 3D printing in small animal orthopedics. Furthermore, this technology provides veterinary medicine with a powerful tool that improves performance, precision, and cost-effectiveness. Nonetheless, the individualized 3D-printed implants have benefited several complex orthopedic procedures in small animals, including joint replacement surgeries, critical size bone defects, tibial tuberosity advancement, patellar groove replacement, limb-sparing surgeries, and other complex orthopedic procedures. The main purpose of this review is to discuss the application of 3D printing in small animal orthopedics based on already published papers as well as the techniques and materials used to fabricate 3D-printed objects. Finally, the advantages, current limitations, and future directions of 3D printing in small animal orthopedics have been addressed. 相似文献