Separation of hematite from banded hematite jasper (BHJ) by magnetic coating

The separation of iron oxide from banded hematite jasper(BHJ) assaying 47.8% Fe, 25.6% Si O2 and 2.30%Al2O3 using selective magnetic coating was studied. Characterization studies of the low grade ore indicate that besides hematite and goethite,jasper, a microcrystalline form of quartzite, is the major impurity associated with this ore. Beneficiation by conventional magnetic separation technique could yield a magnetic concentrate containing 60.8% Fe with 51% Fe recovery. In order to enhance the recovery of the iron oxide minerals, fine magnetite, colloidal magnetite and oleate colloidal magnetite were used as the coating material. When subjected to magnetic separation, the coated ore produces an iron concentrate containing 60.2% Fe with an enhanced recovery of56%. The AFM studies indicate that the coagulation of hematite particles with the oleate colloidal magnetite facilitates the higher recovery of iron particles from the low grade BHJ iron ore under appropriate conditions.     

Cure reaction for modified diallylbisphenol A/diaminodiphenylsulfone/bismaleimide

The glass‐transition temperature as a function of curing conversion for a modified diallylbisphenol A/diaminodiphenylsulfone/bismaleimide (BMI) resin was investigated at different temperature regimes and modeled using a modified Di Benedetto equation. Although the relationship between the glass‐transition temperature and conversion of the BMI system conforms to the Di Benedetto equation for α < 0.6 and at lower cure temperatures, at higher cure temperatures the results deviated significantly from the equation; thus, it was an inadequate model for the system. Fourier transform IR analysis showed that the major crosslinking reactions did not occur during cure for the modified BMI at and below 150°C. However, as the cure temperature was increased, the crosslinking reactions responsible for 3‐dimensional network structures became more dominant. At 190°C the C? N? C_stretch vibration of the uncured maleimide ring converted into succinimide rings in the curing process. Simultaneously, a decrease was observed for the absorbance bands of ? C? H_bending (maleimide). The higher cure temperatures induced a significantly faster initial crosslinking rate and also resulted in a shorter period of time after which further crosslinking was retarded, because the increase in the crosslinks also physically slowed further crosslinking activity. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 227–235, 2002     

A longitudinal study of green-liver osteomyelitis complex in commercial turkeys

Two flocks of Nicholas tom turkeys from separate farms with histories of above-average condemnations for turkey green-liver osteomyelitis complex (TOC) were studied throughout a 16-week growout. Fifty birds from each farm were necropsied each week for 15 weeks, and birds that had green livers, osteomyelitis in the proximal tibia, or swollen joints were cultured for aerobic bacteria along with an equal number of control birds. At processing, TOC lesions and green livers were obtained for bacterial culture and histopathology. Green-liver-associated TOC was not observed until the turkeys were 9 or 10 weeks of age. The incidence of TOC was higher on one farm, which also had a higher incidence of airsacculitis, higher early and weekly mortality, seroconversion to Newcastle disease virus and Mycoplasma meleagridis, and significantly higher average body weights, relative spleen weights, and relative liver weights. Both farms had a high incidence of intestinal lesions and infestation with Ascaridia dissimilis. Histological evaluation of green livers revealed hyperplasia of bile ducts, dilation of sinusoids, and pigment-containing Kupffer's cells, some of which stained positive for iron. The bacterial isolates most frequently cultured from bones and livers were pleomorphic gram-variable coccobacilli, which grew visible colonies only after a series of subcultures and extended incubation.     

Abdominal wall prostheses. Biomechanic and histological study

The best prosthetic material is one which provides the best mechanical resistance with the best biological tolerance. In order to assess the mechanical and histological properties of abdominal wall prostheses, we performed experimental tests in animal models comparing four materials: polypropylene, dacron, polyglactine 910 and a dacron-polyglactine 910 composite. One hundred thirty rabbits were used including 10 controls and 120 test animals. A medial laparotomy was closed with an antemuscular aponevrotic prosthesis in the test animals. Animals were sacrificed at one, two and three months after the operation. Abdominal wall and prosthesis samples were tested to determine resistance to pressure and extension, deformability and elasticity. Histology tests were also done to determine resistance quality and biological tolerance. Dacron was tolerated best and was less resistant than polypropylene, though resistance was satisfactory. There was no advantage with polyglactine compared with non-resorbable prostheses; its only indication would be a septic site. The composite material tested had a resistance comparable with that of dacron but was less well tolerated.     

Microstructural modeling of recrystallization in deformed iron single crystals

Recrystallization kinetics in a (111)[1 0] iron single crystal deformed 70 pet by rolling were characterized experimentally at temperatures between 500°C and 600°C by means of quantitative metallography. A Laplace transform method was applied to the time-dependent global microstructural properties, volume fraction, interface area per unit volume, and the largest intercept-free length (recrystallized grain) to separate nucleation and interface migration effects from the overall recrystallization kinetics. A comprehensive nucleation and growth model was derived from analysis of the microstructural data. The model consisted of the following salient features: (a) nucleation was random and approximately site-saturated with zero incubation time at all temperatures; (b) the recrystallized grains grew three-dimensionally in the shape of prolate spheroids; and (c) interface migration rates were highly anisotropic, the grains growing at an approximately constant rate in one dimension and at a strongly decreasing rate in the other two dimensions. The present findings were compared to a similar earlier study of a deformed iron (111)[ 2] single crystal. The time dependencies of the interface migration rates were rationalized in terms of a deformation-induced, nonuniform distribution of stored energy and an orientation-dependent grain boundary mobility.     

Kinetic study of the curing behavior of bismaleimide modified with diallylbisphenol A

The curing kinetics of bismaleimide modified with diallylbisphenol A were investigated for different ratios of 1,1′‐(methylene di‐4,1‐phenylene) bismaleimide and diallylbisphenol A with differential scanning calorimetry. Multiheating‐rate and isothermal methods were used to study the kinetics of the curing process. The results indicated that the activation energy changed with the extent of conversion. The activation energy obtained by the multiheating‐rate method was higher than that obtained by the isothermal method. Two kinetic models (autocatalytic and nth‐order) were successfully used to model the curing process. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2229–2240, 2003     

Consensus design of repeat proteins

Consensus design is a valuable protein-engineering method that is based on statistical information derived from sequence alignments of homologous proteins. Recently, consensus design was adapted to repeat proteins. We discuss the potential of this novel repeat-based approach for the design of consensus repeat proteins and repeat protein libraries and summarize recent results from such experiments.     

Glass‐transition temperature in the curing process of bismaleimide modified with diallylbisphenol A

The T_g‐conversion relationship, during the thermal curing of different stoichiometric formulations of 1,1′‐(methylene‐di‐4,1‐phenylene) bismaleimide (BMI), modified with o,o′‐diallyl bisphenol A (DABA), was investigated. The DiBenedetto equation was used to model this relationship for the formulation of DABA‐1 (BMI : DABA, 1 : 1). Based on this model, the T_g‐conversion relationship of formulation DABA‐0.5 (BMI : DABA, 1 : 0.5) was modeled. The high consistency between the model curve and experimental data showed that the change of T_g, attributed to copolymerization between BMI and DABA in DABA‐0.5, in the low‐conversion regime, was the same as that in DABA‐1. This also verifies that, for the formulation DABA‐0.5, copolymerization and homopolymerization do not overlap with each other. The reactions progressed sequentially and homopolymerization occurred after completion of copolymerization. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3244–3247, 2004     

Self-organized porous TiO2 and ZrO2 produced by anodization

The present work investigates the electrochemical formation of self-organized high aspect ratio TiO₂ and ZrO₂ nanotube layers. The formation and growth of a self-organized porous layer can be achieved directly by anodization without any templates in fluoride containing electrolytes. The morphology of the porous layers is affected by the electrochemical conditions such as the electrolyte composition, the pH and the exact polarization treatment (such as the potential sweep rate from the open-circuit potential to the anodizing potential). For Ti, nanotube layers are formed with diameters varying from approx. 20 nm to 100 nm and lengths from approx. 0.25 μm to 2.5 μm depending on the electrolytes and pH. On the other hand, for Zr, tubes of 50 nm in diameter and up to approx. 17 μm in length can be grown—a key parameter in this case is the potential sweep rate. The large difference between Ti and Zr in the achievable thickness of nanotube layers indicates a difference in the growth mechanism which may be based on the different chemical dissolution rates of electrochemically formed oxides.