切向结构永磁同步电机磁钢径向并联组合研究

针对低速大转矩切向结构永磁同步电机中磁钢尺寸对性能的影响进行研究.提出一种"工"字形排布的磁钢径向并联组合优化方案.在保证电机磁钢轴向长度和体积不变前提下,分析磁钢磁化方向长度变化对电机性能的影响.分析表明:磁钢的磁化方向长度在一定范围内增加可降低磁钢漏磁、增大反电动势和降低转矩波动;但磁钢的磁化方向长度过度增加会大大降低电机磁通面积,使得电机反电动势不增反降.在此基础上,提出一种降低磁钢漏磁、增大反电动势和降低转矩波动的三块磁钢径向并联组合的"工"字形排布方案:近气隙侧和近隔磁槽侧磁钢槽内分别插入磁化方向长度短、径向宽度窄的磁钢以降低近气隙侧和近隔磁套侧磁钢漏磁;近气隙侧磁钢和近隔磁槽侧磁钢之间采用磁化方向长度较短的磁钢以保证磁钢磁通面积降低得不多.通过仿真实验验证所提方案的可行性.     

Facile growth of novel morphology correlated Ag/Co-doped ZnO nanowire/flake-like composites for superior photoelectrochemical water splitting activity

In this paper, novel morphology correlation between silver nanowires (AgNWs) and cobalt (Co)-doped ZnO (Co-ZnO) flake-like thin films (nanowire/flake-like) has been proposed for enhanced photoelectrochemical (PEC) water splitting activity. Here in, high-quality AgNWs/Co-ZnO heterostructures enabled superior visible light water splitting activity compared to the pure ZnO and AgNWs/ZnO. To address the strategic effect of AgNWs coupling and transition metal (Co-2?at%) doping into the ZnO host lattice, we have carried out the X-ray diffraction, field emission scanning microscopy, X-ray photoelectron spectroscopy, UV–Vis transmittance, water contact angle and PEC analyses. In this way, PEC water splitting activity was mainly examined by linear sweep voltammetry (I-V), amperometric I-t and photoconversion efficiency (η) studies. The experimental results provide clear evidence of morphology correlation between AgNWs and Co-ZnO flake-like structures for strong visible light absorption. Specifically, AgNWs/Co-ZnO composites exhibited significant enhancement in the photocurrent density (7.0?×?10^?4 A/cm²) than AgNWs/ZnO (3.2?×?10^?4 A/cm²) and pure ZnO (1.5?×?10^?6 A/cm²). As a result, detailed AgNWs/Co-ZnO geometry has great potential for photoconversion efficiency (0.73%). In a word, the merits of controllable AgNWs/Co-ZnO heterostructure are proposed to improve the visible light harvesting and charge carrier generation for energy conversion devices.     

An efficient technique for the multilayered microwave and millimeter planar waveguides

The method of lines is extended to the multilayered inhomogenous dielectric layers by means of the additional transformation and the recurrence matrix. The computed dispersion diagrams for the multilayered planar waveguides agree very well with the results from other authors. New results for a six layer structure are given.     

Diffusion bonding of an aluminium-lithium alloy (AA8090) using aluminium-copper alloy interlayers

Diffusion bonds have been produced between sheets of an Al-Li-Cu-Mg-Zr alloy using aluminium-4% copper vapour deposited metallic interlayers. Microstructural changes occurred both in the parent alloy and in the bond interface after diffusion bonding cycles and post-bonding heat treatments were analysed. Different metallographic techniques (light microscopy, scanning and transmission electron microscopy) have been used. Diffusion bonding trials were carried out using the same alloy (AA8090), both in non-superplastic (T6) and superplastic conditions. Differences in their behaviours in relation to diffusion bonding were observed.     

基于纠错编码和小波变换的数字图像水印算法

文章提出了一种基于小波变换和纠错编码的数字图像水印算法,该算法不需要利用原始图像。实验结果表明,该算法较好地保持了图像的质量,并大大提高了检测的可靠性,对常见的图像处理方法显示了较强的鲁棒性。     

拟动力实验中的数值积分方法

拟动力实验方法是目前最新的抗震实验方法，它克服了振动台实验中承载力不足、拟静力实验中无法真实模拟地震过程的缺点．本文详细论述了拟动力实验中的数值积分方法，其中包括：显式方法，隐式方法以及采用于结构技术时所需的特殊教值积分方法，并对这些方法的适用范围作了介绍．     

亚铜离子氨浸法的发展前景展望

亚铜离子氨浸法作为大洋多金属结核处理方法之一，一直被认为是一个很有前途的冶金处理工艺，是催化化学还原技术在冶金生产中的具体应用，具有流程简单，能耗低，浸出选择性好，产品结构灵活，市场适应能力强，浸出试剂腐蚀性与毒性小，环境污染小等优点。     

MIM Fe基合金的合金化强化

研究金属粉末注射成形铁基合金在强还原性氢气氛烧结条件下的合金化强化效果，结果表明，添加Ｃｕ、Ｎｉ、Ｍｏ等元素能取得显著的固溶强化效果，其中成分为Ｆｅ－２Ｎｉ－２Ｃｕ－０．４５Ｍｏ的机械性能达到σｂ＝４８３ＭＰａ，σｓ＝３４０ＭＰａ，δ＝９％和ＨＲＢ８３。     

基于改进粒子群优化算法的外转子永磁同步电机的多目标优化设计

为降低外转子永磁同步电机(ERPMSM) 作为皮带输送机驱动电机时的永磁体成本并提高电机性能,提出基于响应面法(RSM)和改进多目标粒子群优化(IMOPSO)算法的优化设计方法。在建立电机基本结构的基础上,将永磁体尺寸、气隙长度、槽口宽度等作为优化参数,将永磁体成本、输出转矩、转矩脉动等作为优化目标。通过参数灵敏度分析筛选出显著参数,基于RSM结合有限元仿真建立样本空间,并拟合出优化目标和优化参数的函数关系,通过IMOPSO寻优。最后对比优化前后的方案结果,所提多目标优化算法准确可靠且具有更好的收敛性和多样性,能够在降低永磁体成本的同时优化电机的性能。     

Microstructural aspects of hypervelocity impact cratering and jetting in copper

Light and transmission electron microscopy techniques have been applied in observations of hypervelocity impact craters in two different copper targets: a 38 m grain size mill-processed target, and a 763 m grain size annealed target, the smaller grained target being impacted with a 1100 aluminium sphere and the larger grained target being impacted with a soda-lime glass sphere, at velocities near 6 km s^–1. Both target craters exhibited dynamic recrystallization near the crater wall. The jetting associated with these two craters was very different. Considerably more plastic flow and a larger rim characterized the larger grained target. No significant melt-related phenomena were observed either near the crater wall or in the jetted rim for either crater. Consequently, the principal features of crater formation involve extreme plastic flow in the solid state. Microbands were observed to occur profusely in a zone below the smaller grained mill-processed target crater while more profuse and extremely long, unidirectional bundles of microbands (which were coincident with traces of {1 1 1} planes) occurred below the annealed larger grained target crater. These observations attest to the dominant and unique role played by deformation microbands in cratering in copper, because essentially no deformation twins were observed in either target.