Macroscopic and crystallographic density of solid-state extruded polyethylene

Summary The influence of draw ratio on macroscopic and crystallographic density of polyethylene with different initial morphologies, has been investigated by solid-state extrusion. An initial drop followed by an increase in macroscopic density as a function of draw ratio has been observed. Since precision X-ray measurements of unit cell parameters showed no variation of crystallographic density, it was concluded that plastic deformation of polyethylene upon drawing proceeds with a decrease of the degree of crystallinity. This was confirmed by differential scanning calorimetry.     

Environmental Fatigue and Static Behavior of RC Beams Strengthened with Carbon-Fiber-Reinforced Polymer

Many countries around the world have tremendous needs to repair and strengthen their transportation infrastructure. Almost everywhere, traffic loads have reached levels largely exceeding design expectations. Northern countries also experience severe winter conditions that are combined with an extensive use of deicing salts and accelerate structural deterioration. In Canada, the extent of deterioration has prompted many authorities, including the federal and provincial governments, to investigate the potential use of fiber-reinforced polymer products to extend the life of their existing structures. However, it is widely recognized that the large-scale implementation of these products is often impaired by the lack of data on their durability. This paper presents an experimental project undertaken in order to assess the durability of reinforced concrete beams externally strengthened with two types of carbon-fiber-reinforced polymer (CFRP). The beams were first exposed to either wet-dry cycles or continuous immersion in water and then were loaded in fatigue. Finally, they were tested quasi-statically under four-point bending up to failure. The test results presented here provide some insights on the potential long-term performance of CFRP-strengthened beams exposed to severe environmental conditions.     

New method for analysis of electromagnetic coupling to an angled two-strip transmission line

The electromagnetic coupling to an angled two-strip transmission line is analysed to constructing an angled two-plate transmission line equivalent to the original geometry, and then solving the cylindrical transmission line equations of the original source analytically. The results agree with the numerical values of the circuit-concept approach.<>     

Polarization-based cooperative directional MAC protocol for ad hoc networks

Numerous directional medium access control (DMAC) protocols have been developed to enhance the capacity of ad hoc networks using the underlying advanced physical layer techniques, such as beam-forming, multiuser detection (MUD), and multiple-input–multiple-output (MIMO). In this paper, we propose an innovative fully distributed DMAC protocol that cooperatively makes use of polarization diversity in low-mobility urban/suburban outdoor wireless ad hoc network environment. In the proposed cooperative polarization DMAC protocol (CPDMAC), each node directionally senses on both vertical and horizontal polarizations and dynamically adapts polarization that minimizes overall interference in the ad hoc network. Analysis is performed to establish relationship between vertically and horizontally polarized nodes in the network. Further, a theoretical lower bound is derived for probability of successful transmission to show capacity improvement as a function of cross polarization ratio (CPR). Simulation results confirm from 2% up to 400% improvement in average node throughput at data rate of 1.95 Mbps when compared to the traditional DMAC protocol. Moreover, our study clearly shows that the average throughput difference increases with increasing node density when compared to the traditional DMAC protocol.     

Practical adaptive notch filter for missile bending mode rejection

A practical adaptive notch filter based on the /spl Hscr//sub /spl infin// bending frequency estimator is proposed to remove the time-varying structural mode of a missile from the rate sensor measurements. Simulation results using flight test data show the reliable bending frequency estimation performance with this new technique.     

Highly Stretchable and Sensitive Strain Sensors Using Fragmentized Graphene Foam

Stretchable electronics have recently been extensively investigated for the development of highly advanced human‐interactive devices. Here, a highly stretchable and sensitive strain sensor is fabricated based on the composite of fragmentized graphene foam (FGF) and polydimethylsiloxane (PDMS). A graphene foam (GF) is disintegrated into 200–300 μm sized fragments while maintaining its 3D structure by using a vortex mixer, forming a percolation network of the FGFs. The strain sensor shows high sensitivity with a gauge factor of 15 to 29, which is much higher compared to the GF/PDMS strain sensor with a gauge factor of 2.2. It is attributed to the great change in the contact resistance between FGFs over the large contact area, when stretched. In addition to the high sensitivity, the FGF/PDMS strain sensor exhibits high stretchability over 70% and high durability over 10 000 stretching‐releasing cycles. When the sensor is attached to the human body, it functions as a health‐monitoring device by detecting various human motions such as the bending of elbows and fingers in addition to the pulse of radial artery. Finally, by using the FGF, PDMS, and μ‐LEDs, a stretchable touch sensor array is fabricated, thus demonstrating its potential application as an artificial skin.