Strain‐rate‐dependent mechanical properties of polypropylene separator for lithium‐ion batteries

The mechanical integrity of battery separators is critical for battery safety and durability. A comprehensive study of strain‐rate‐dependent tensile and puncture properties of a polypropylene lithium‐ion battery separator is presented here with a new model. Due to anisotropy of the polymeric membrane, tensile testing was conducted for different directions. Results showed that tensile strength and elastic modulus were increased 1000% and 500%, respectively, for different directions. It was also demonstrated that tensile strength changed 10 to 25% with strain rate (1.67 × 10^?4 to 1.67 × 10^?1 s^?1) for different directions. An equation was obtained for the first time for flow stress versus strain rate at varied tensile directions with respect to machine direction. Moreover, puncture testing was performed and it was shown that puncture strength was increased 140% with increasing strain rate from 0.25 to 250 mm min^?1. Two failure modes were also observed in puncture samples. Finally, Eyring's model was used to calculate activation enthalpy of the porous polypropylene separator. © 2020 Society of Chemical Industry     

Influence of Different Additives on the Interaction of Quinolone Antibiotic Drug with Surfactant: Conductivity and Cloud Point Measurement Study

Conductometric and cloud point (CP) measurement studies have been performed to investigate the interaction of tetradecyltrimethylammonium bromide (TTAB) and Triton® X-100 (TX-100) with ciprofloxacin hydrochloride (CFH) in different solvents over the temperature range of 295.15–315.15 K. CFH is used for the treatment of various bacterial infections. The observed critical micelle concentration (CMC) values of TTAB were found to be reduced in the presence of electrolytes (Na₂SO₄/Na₃PO₄), and this reduction proceeds with the elevation of salt concentration. The order of the CMC of TTAB follows the trend: > >. The observed CMC values of TTAB were found to increase with increasing temperature and decrease with increasing concentration of CFH in aqueous medium. The values of Gibbs free energy of micellization () for the TTAB/TTAB + CFH mixture were found to be negative, implying spontaneous micellization. The estimated CP of TX-100 decreases with increasing concentration of TX-100 in aqueous medium. The CP values first decrease with increasing concentration of CFH and then increase at higher concentration of CFH almost in all cases investigated. The values of free energy of clouding were found to be positive in all cases studied implying that phase separation of TX-100 was nonspontaneous. The other thermodynamic parameters associated with the micellization of TTAB and the phase separation of TX-100 were estimated and explained.     

Surface structural and solar absorptance features of nitrate-based copper-cobalt oxides composite coatings: Experimental studies and molecular dynamic simulation

The copper and cobalt oxides composites coatings on aluminum substrates have been successfully synthesized via sol-gel method using nitrate-based sol precursors. The composites were characterized by X-ray Diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Field Emission Scanning Electron Microscopy (FESEM), Atomic Force Microscopy (AFM), and UV–Vis–NIR spectrophotometry. The sol-gel reactions were discussed and Molecular Dynamics (MD) simulation was integrated into the study to predict molecules assembly properties. The XRD analyses revealed that the CuO and the Co₃O₄ composites were formed after the annealing process with the average difference of the calculated lattice parameters compared to ICDDs was 1.17%. The surface electronic structure was mainly consisted of tetrahedral Cu(I), octahedral Cu(II), tetrahedral Co(II), octahedral Co(III) as well as surface, sub-surface and lattice oxygen O^?. The XRD, XPS and MD simulation results showed that there was minimal (or possibly non-existing) indication of copper-cobalt mixed phase oxides formations. FESEM and AFM surveys revealed that the coating had a porous surface composed of interlinked nanoparticles in the range of ~?10 to ~?40?nm. UV–Vis–NIR reflectance spectra showed that the sol precursors concentration and the dip-drying cycle significantly influenced the absorptance value with optimum absorptance (α) of 88.7% exhibited by coating synthesized using sol concentration of 0.1?M and 10 dip-drying cycles. High absorptance value and simplicity in the synthesis process render the coatings to be very promising candidates for solar selective absorber (SSA) applications.     

Antimicrobial residues survey by LC-MS in food-producing animals in Lebanon

ABSTRACT

The treatment of animals with antimicrobial products may lead to the contamination of edible tissues by their residues, which may represent a risk to human health. Therefore, this study aimed to determine the level of antimicrobial residues in food-producing animals (chicken, beef, and milk) in Lebanon. A total of 310 samples were collected and analysed using an LC-MS/MS for the determination of 48 compounds belonging to different families in order to map their compliance according to the European Commission decision 2002/657/EC. Results show that 60% of the analysed samples were not contaminated by any residue, while 12% presented a concentration higher than the MRLs for tetracyclines, sulphonamides, quinolones, and macrolides. Results revealed that chicken were the most contaminated by antimicrobial residues, when compared to beef and milk. The obtained results demonstrate the uncontrolled use of antimicrobials in some Lebanese farms and claim for better management of livestock.     

Optimal production-inventory policy for make-to-order versus make-to-stock based on the M/Er/1 queuing model

This paper analyzes a multi-product production / inventory system where demands for each item arrive according to a Poisson process and the production time for each product has an Erlang distribution. The paper proposes an optimality condition that specifies whether each product should be produced make-to-stock or make-to-order. In the event a product should be produced make-to-stock, an approach for computing the optimal base-stock level is proposed. Numerical examples are given for illustrative purpose.     

Aggregation of Induction Motor Loads for Transient Stability Studies

This study investigates the dynamic representation of a group of induction motors by one or more equivalent motors. The unknown parameters of the equivalent are estimated through a weighted-least-squares procedure. Verification of simulated results with experimental ones suggests that a fifth order dynamic model of the aggregate with a ninth order parameter model is appropriate. The least squares technique was found to provide good convergence characteristics subject to satisfaction of the following conditions good initial estimate of the parameters, proper selection of acceleration factors and homogenity of the motor group.