Synthesis,characterization and charge transport properties of Pr–Ni Co-doped SrFe2O4 spinel for high frequency devices applications

Ferrites are materials of interest due to their broad applications in high technological devices and a lot of research has been focused to synthesize new ferrites. In this regard, an effort has been devoted to synthesize spinel Pr–Ni co-substituted strontium ferrites with a nominal formula of Sr_1-xPr_xFe_2-yNi_yO₄ (0.0 ≤ x ≤ 0.1, 0.0 ≤ y ≤ 1.0). The cubic structure of pure and Pr–Ni co-substituted strontium ferrite samples calcinated at 1073 K for 3 h has been confirmed through X-ray diffraction (XRD). Average sizes of crystallites (18–25 nm) have been estimated from XRD analysis and nanometer particle sizes of synthesized ferrites have been further verified by scanning electron microscopy (SEM). SEM results have also shown that particles are mostly agglomerated and all the samples possess porosity. It has been observed that at 298 K, the values of resistivity (ρ) increase, while that of AC conductivity, dielectric loss, and dielectric constants decrease with increasing amounts of Pr³⁺ and Ni²⁺ ions. The values of dielectric parameters initially decrease with frequency and later become constant and can be explained on the basis of dielectric polarization. Electrochemical impedance spectroscopy (EIS) studies show that the charge transport phenomenon in ferrite materials is mainly controlled via grain boundaries. Overall, synthesized ferrite materials own enhanced resistivity values in the range of 1.38 × 10⁹–1.94 × 10⁹ Ω cm and minimum dielectric losses, which makes them suitable candidates for high frequency devices applications.     

Product mix determination in the presence of alternate process plans and stochastic demand

The product mix problem in the presence of alternate process plans under uncertain demand is formulated as a non-linear programming model. A heuristic solution procedure based on lagrangean relaxation technique is also presented.     

APPLICATION OF RESPONSE SURFACE METHODOLOGY FOR THE MAXIMIZATION OF CONCORA CRUSH RESISTANCE OF PAPERBOARD

Response surface methodology is often used by researchers in different fields to determine the optimum values for controlled variables to maximize or minimize the response variables. Either maximization or minimization might be necessary depending on the response property. For example, if the response variable represents the yield of a process, maximization could be necessary; on the other hand, if the response variable is the biological oxygen demand (BOD) of an effluent the aim would definitely be minimization

Response surface methodology can be used two ways. It can be applied to the full-scale production or it can be scaled to a laboratory or the pilot plant. When applied to the full-scale production, the method is known as evolutionary operation (EVOP). EVOP is the continuous optimization of a process. The optimum conditions in a production plant can change depending on many factors such as raw material, ambient temperature, and equipment wear. Therefore, controlled variables should be optimized continuously to keep the response variable as close as possible to the maximum or minimum value. Hence, controlled variables are systematically changed around a center point to depict any shift of the response variable from the extreme. A thorough discussion of EVOP is given by Box, Evolutionary Operation: A Method for Increasing Industrial Productivity, Appl. Statist., 6, 81-101 (1957).     

Dyes from the leaves of deciduous plants with a high tannin content for wool

The aqueous leaf extracts of five different deciduous plants, namely, silver oak, flame of the forest, tanner’s senna, wattle and serviceberry, were used on their own and in combination with aluminium sulphate, stannous chloride and ferrous sulphate to dye wool by a simultaneous mordanting technique. The washing and light fastness properties of the developed shades were moderate to good. Based on the CIE 2000 spectral colour coordinate values (K/S, ΔL, Δa, Δb and ΔE), the developed shades were classified into four groups: yellow/brown, yellow, orange and dark grey. The use of aluminium sulphate gave medium shades (K/S = 8.24), while the stannous chloride and ferrous sulphate mordants provided deep shades (K/S = 30.5). Statistical analyses have shown that only the type of mordant and not the dye source significantly influenced the development of colour on wool. Hence, it was theoretically possible to use five selected leaves as a single mixture to produce four different colours on wool.     

Soil–conduit interaction: an artificial intelligence application for reinforced concrete and corrugated steel conduits

Neural Computing and Applications - Marston’s load theory is commonly used for understanding the soil–conduit interaction. However, there are no practical methods available which can...     

Scanning Auger electron spectroscopy study of the oxide film formed on dendritic and interdendritic regions of C containing Fe3Al intermetallic

The oxide films formed during early stage of oxidation at 800 °C on dendritic and interdendritic regions of the cast Fe–16Al–1C (wt.%) alloy were studied using scanning Auger electron spectroscopy. Microhardness measurement and elemental depth profiles by Auger spectroscopy reveal that the carbide, Fe₃AlC_0.69, is the major constituent of the interdendritic region, while dendrites are predominantly Fe₃Al phase. Between the two, the interdendritic region is found to be more prone to oxidation than the dendritic region, which was attributed to presence of carbides with low-Al content. In spite of the difference in oxide film thickness exhibited by both the phases, they consist of an inner aluminium oxide layer and an outer iron oxide layer.     

Ambient‐cured polyesteramide‐based anticorrosive coatings from linseed oil—A sustainable resource

Ambient‐cured polyesteramide (APEA) coating resin synthesized from dihydroxy fatty amide obtained from linseed oil, a sustainable resource, and poly(styrene‐co‐maleic anhydride), a bifunctional acid component, was found to exhibit improved physicomechanical and anticorrosive properties. The structural elucidation of APEA resin has been carried out by FTIR, ¹H‐NMR, and ¹³C‐NMR spectroscopies. The physicomechanical and chemical resistance properties were investigated by standard methods. The corrosion resistance performance was evaluated in acid, alkali, and organic solvent. The thermal behavior was studied by TGA technique. A comparative study of these properties of APEA with reported baked polyesteramide (PEA) coatings was carried out. A remarkable improvement in the drying property of APEA was observed. The APEA coatings also showed improved physicomechanical and anticorrosive properties as compared to the baked PEA coatings. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1818–1824, 2005     

Compositional trend analysis on poly(phenylene ether) based thermoplastic elastomers

Detailed statistical trend analysis of thermoplastic elastomers based on poly (phenylene ether) (PPE), polystyrene (PS), ethylene vinyl acetate (EVA) and styrene‐ethylene‐butylene‐styrene (SEBS) was done through Design Expert software by Stat‐Ease. D optimal crossed design was followed to capture the interaction with the parameters. Effect of blend ratio, vinyl acetate (VA) content of EVA, molecular weight (MW) of SEBS and intrinsic viscosity (IV) of PPE on the blend performance (response) was studied in detail. Design of Experiment (DOE) analysis showed the “optimized formulation” of the blend. Increase in PPE‐polystyrene (PS) content increased tensile strength and modulus of the blend, followed by a decrease in strain at break. However, EVA had a reverse effect on tensile strength and modulus. Strain at break increased significantly with increasing SEBS content in the blend. Graphical and numerical optimization showed that superior mechanical properties (tensile strength, strain at break and modulus) could be achieved at VA content ～ 50% at a particular loading of EVA. Low MW SEBS was found to be more compatible with the other components of the blend. Mechanical properties of the quaternary blend were marginally affected with change in IV of PPE in the range of 0.33 to 0.46. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007