Reducing cycle times in manufacturing and supply chains by input and service rate smoothing

A key performance parameter of a manufacturing network or supply chain is its cycle time; the time that a typical item spends in the network. A previous simulation study on a semiconductor assembly and test facility showed that cycle times could be reduced by having smooth input and service rates. This suggested that there is a “cycle time principle” that, for a system with a specified throughput or input rate, the shortest cycle times are obtained when the input and service rates do not vary over time. We prove that this principle is true for the M/G/1 and M/M/s queueing systems and Jackson networks. The analysis involves establishing several results on the concavity of waiting time probabilities and the convexity of expected waiting times and queue lengths, as functions of input and service rates. These results also have natural uses in other optimization problems.     

Wavelength-tunable 40-GHz picosecond harmonically mode-locked fiber laser source

We demonstrate a novel 40-GHz mode-locked fiber laser that utilizes a single active device to provide both gain and mode-locking. The laser produces pulses as short as 2.2 ps, is tunable over a 27-nm band centered at 1553 nm, and exhibits long-term stability without cavity-length feedback control. The pulse train at 1556 nm was used in a 40-Gb/s transmission experiment over 45 km with a low 0.4-dB power penalty.     

Effect of Freezer Programs on Real-Time Storage Results of Dissolution Profiles

Carstensen and Rhodes¹ have suggested that when, in stability programs, assays cannot be performed immediately after the protocol-designated storage time, then freezing them until such a time when assays can be performed would be a reasonable manner to retain the protocol schedule. They caution, however, that such a procedure may not be valid for dissolution data. The article to follow deals with real-time data showing that such a process is feasible for Nalidixic Acid tablets (and presumably for other tablets as well), and that, furthermore, the dissolution pattern would seem to be “frozen” as well.     

The effects of pressure on the isothermal fluid behavior of bituminous coals

An investigation into the effects of pressure (helium gas) on the isothermal fluid behavior includes: (1) the effect of pressure on the rate of melting and coking as evidenced by the rate constants k(melt) and k(coke); (2) the effect of pressure on the energies of activation of melting and coking; (3) the effects of pressure on the characteristic times; (4) the effects of pressure on the maximum isothermal fluidity. Results from the effects of pressure on k(melt) revealed that it was generally the high total sulfur, low nitrogen, low reactives/mineral matter ratio, medium rank coals which show the greatest increase in k(melt), whereas the highest rank coals show the least decrease in k(coke). The energies of activation of melting and coking were not significantly affected by pressure. The investigation also reveals increases or decreases in the respective times of softening, maximum fluidity, resolidification and total time of fluid behavior under isothermal pressurized conditions. There appears the possibility that these shifts may be rank dependent. Additionally, the lower rank coals show the largest relative increase in their fluidities when subjected to pressure. Empirical relationships were derived in order to quantitatively predict the maximum isothermal fluidity for most (fluid) coals at a given pressure.     

The Effects of H2O, CO and CO2 on the H2 Permeance and Surface Characteristics of 1 mm Thick Pd80wt%Cu Membranes

The hydrogen permeance of 1 mm-thick Pd_80wt%Cu foils was measured in the presence of equimolar mixtures of H₂ with CO, CO₂ or H₂O over the temperature and total pressure ranges of 623–1,173 K and 0.62–2.86 MPa, respectively. In all cases, permeance losses at 623 and 738 K were very modest. At higher temperatures, more significant decreases in membrane permeance were observed with the highest reduction of about 50% occurring when macroscopic carbon deposition occurred on the membrane surface during H₂–CO exposure at 908 K. The more worrisome effects of exposure to these gases, however, were the micron-scale surface defects observed at 908 and 1,038 K. Although the 1 mm thick disk membranes retained their mechanical integrity, such defects could cause catastrophic failure of ultra-thin, Pd–Cu membranes (1–5 μm thick) deposited on porous substrates.     

A distributed adverse drug reaction detection system using intelligent agents with a fuzzy recognition‐primed decision model

Discovering unknown adverse drug reactions (ADRs) in postmarketing surveillance as early as possible is highly desirable. Nevertheless, current postmarketing surveillance methods largely rely on spontaneous reports that suffer from serious underreporting, latency, and inconsistent reporting. Thus these methods are not ideal for rapidly identifying rare ADRs. The multiagent systems paradigm is an emerging and effective approach to tackling distributed problems, especially when data sources and knowledge are geographically located in different places and coordination and collaboration are necessary for decision making. In this article, we propose an active, multiagent framework for early detection of ADRs by utilizing electronic patient data distributed across many different sources and locations. In this framework, intelligent agents assist a team of experts based on the well‐known human decision‐making model called Recognition‐Primed Decision (RPD). We generalize the RPD model to a fuzzy RPD model and utilize fuzzy logic technology to not only represent, interpret, and compute imprecise and subjective cues that are commonly encountered in the ADR problem but also to retrieve prior experiences by evaluating the extent of matching between the current situation and a past experience. We describe our preliminary multiagent system design and illustrate its potential benefits for assisting expert teams in early detection of previously unknown ADRs. © 2007 Wiley Periodicals, Inc. Int J Int Syst 22: 827–845, 2007.     

Ionization of Acetylacetone in Me2SO—Water Mixtures. Reactivity—Selectivity Principle or Principle of Imperfect Synchronization?

Rate constants for the reversible deprotonation of acetylacetone were measured in carboxylate and amine buffers in water and in 50%, 90% and 95% Me₂SO at 20°C. The Brønsted plot for the carboxylate ions is curved in the Me₂SO—water mixtures, but straight in water. The curvature is in the direction predicted by the Reactivity—Selectivity Principle (RSP). However, the Brønsted plot for the reaction with primary amines is straight in all solvents. This suggests that the curvature observerd with the carboxylate ions is caused by loss of solvation of the base; this loss of solvation is ahead of bond formation in the transition state rather than being a manifestation of the RSP. (Note that all Brønsted plots are based on pK_a values measured in the respective solvents.) The intrinsic rate constant (k₀) for proton transfer increases with the addition of Me₂SO, and more so with the carboxylate buffers than with the amines. This increase in k₀ is attributed to delayed solvation of the developing enolate ion in the transition state; with the carboxylate buffers, an additional factor is the early loss of solvation of the base. The various solvation effects observed in this study can all be understood in the context of the Principle of Imperfect Synchronization (PIS).