Spray dryer processed graphene oxide/reduced graphene oxide for high-performance supercapacitor

This study deals with the utility of mini spray dryer process to improve the dispersibility, of graphene oxide(GO) and its application for high-performance supercapacitor. Initially, the neutral solution of GO was obtained using the modified Hummer's method. After this, the prepared GO solution was processed by mini spray dryer to obtain a more purified, lighter, and dispersed form of GO which is named as spray dryer processed GO (SPGO). The SPGO thus obtained showed excellent dispersibility behavior with various solvents, which is not found in case of conventional oven drying. Furthermore, utility of SPGO and its reduced form (r-SPGO) for supercapacitor applications have been investigated. Results obtained from the cyclic voltammetry(CV) analysis, impedance, and charge-discharge behavior of supercapacitor fabricated using r-SPGO shows enhanced features. Therefore, the simple spray dried GO and its reduced form, that is, r-SPGO can be utilized as a potential candidate for the supercapacitor application. Herein, as synthesized SPGO exhibited the specific capacitance of 12.07 and 37.6 F/g with PVA-H₃PO₄ and 1 mol/L H₃PO₄, respectively, at a scan rate of 5 mV/s. On the other hand, reduced form of SPGO, that is, r-SPGO showed the specific capacitance of 27.16 and 230 F/g with PVA-H₃PO₄ and 1 mol/L H₃PO₄, respectively.     

Effect of oxygen deficiency (δ) on transition temperature of yttrium cuprate superconductors

The nature of pairing mechanism as well as transition temperature of yttrium cuprates is discussed using the strong coupling theory. An interaction potential has been developed for the layered structure with two conducting CuO₂(a–b) layers in a unit cell. The interaction potential properly takes care of electron-electron, electron-phonon and electron-plasmon interactions. Furthermore, the electron-phonon coupling parameter (λ), the modified Coulomb repulsive parameter (μ*) and the 2D acoustic phonon (plasmon) energy as a function of oxygen deficiency is worked out. Finally, the superconducting transition temperature (T _c) is then evaluated by using these coupling parameters and obtainedT _c = 95(92)K for Y(Yb)Ba₂Cu₃O_7−δ superconductors withδ = 0·0. The model parameters estimated from the layered structure approach are consistent with the strong coupling theory. The result deduced on the variation ofT _c withδ are in fair agreement with the earlier reported data on yttrium cuprates. The analysis of the above results are discussed.     

A Monte Carlo simulation study of the mechanical and conformational properties of networks of helical polymers. I. General concepts

We study the mechanical and conformational properties of networks of helical polymers with a combination of Monte Carlo simulations based on the Wang-Landau algorithm and the three-chain model. We find that the stress-strain behavior of these networks has novel features not observed in typical networks made of synthetic polymers. In particular, we find that as these networks are stretched they first strengthen, then soften and finally strengthen again. This non-monotonic behavior of the stress correlates with the one of the helical content and is rationalized by the elongation-induced formation and melting of the helical structure of the polymer. We complement these results with a study of other conformational properties of the polymer strands that clarify the molecular mechanisms behind the mechanical behavior of these networks. Finally, we present a qualitative comparison of some of our results with the theoretical ones recently reported by Kutter and Terentjev.     

Target Location Estimation in Sensor Networks With Quantized Data

A signal intensity based maximum-likelihood (ML) target location estimator that uses quantized data is proposed for wireless sensor networks (WSNs). The signal intensity received at local sensors is assumed to be inversely proportional to the square of the distance from the target. The ML estimator and its corresponding Crameacuter-Rao lower bound (CRLB) are derived. Simulation results show that this estimator is much more accurate than the heuristic weighted average methods, and it can reach the CRLB even with a relatively small amount of data. In addition, the optimal design method for quantization thresholds, as well as two heuristic design methods, are presented. The heuristic design methods, which require minimum prior information about the system, prove to be very robust under various situations     

CO2 laser annealing of plasma-deposited high-Tcsuperconducting thick films

Recent advances in the fabrication of high-T _c superconducting thick films demand processing techniques which can eliminate film/substrate interdifiusion that occurs during subsequent post-annealing heat treatment after the film is deposited, thereby limiting the application of the thick films for devices. The present study evaluates laser annealing techniques for plasma-deposited Y-Ba-Cu-O thick films using a high-energy CO₂ laser (10.6m) in a continuous wave mode. The results are compared with those obtained by conventional furnace annealing techniques necessary for post-heat treatment of as-deposited superconducting thick films. The high-T _c superconducting phase is recovered by cationic diffusion during subsequent post-annealing heat treatment. Crystallographic phases and microstructural characterization have been performed using XRD, SEM, and EPMA analytical techniques. The significance of the technology lies in the elimination of film/substrate interdiffusion problems, thereby resulting in high-quality superconducting thick films. The technology will significantly reduce the post-annealing times usually required by conventional furnace annealing techniques.     

Hexamethyl cyclotrisiloxane–styrene block copolymers and their chemical composition

Triblock copolymers of hexamethyl cyclotrisiloxane (D₃) and styrene were synthesized by first preparing “living” species of polystyrene dianion followed by polymerization of D₃. The chain lenght of polymeric blocks could be controlled in a predictable fashion leading to a central hard block of polystyrene and the two end segments of amorphous polydimethylsiloxane having narrow molecular weight distribution, were characterized by gel permeation chromatography. The chemical composition of block copolymers was determined by silicon analysis and infrared and nuclear magnetic resonance spectra. Thermal aging of block copolymers at 150, 200, and 300°C was also discussed.     

Fabrication and characterization of electrospun psyllium husk-based nanofibers for tissue regeneration

The present study reports for first time the blending of psyllium husk (PH) powder/gelatin (G) in the polymer-rich composition of polyvinyl alcohol (PVA) to make an electrospinnable solution. The composite was prepared in 3 different ratios viz., 100% (wt/wt) (PVA + PH), 75% + 25% (PVA + 75PH + 25G) (wt/wt) and 50% + 50% (PVA + 50PH + 50G) (wt/wt) in 6% PVA solution. Optimum electrospinning parameters were evaluated for all the prepared blends. The fabricated nanofibers were characterized by scanning electron microscopy (SEM), attenuated total reflectance-Fourier transform infrared, differential scanning calorimetry, porosity percentage, and fiber orientation using ImageJ software. A qualitative in vitro degradation study at room temperature is supported by SEM images. The cellular interactions were characterized by MTT assay of NIH-3T3 fibroblast cells for 2 and 4 days with an optimum cell growth of >50% by fourth day of culture and long-term cultivation of L929-RFP cells was observed for 10 days. The nanofibers were formed in the range of 49–600 nm. PVA + 75PH + 25G when cultured with L929-RFP cells exhibited highest fluorescence intensity and thus supported cellular proliferation significantly. Based on the results obtained from various analyses, we anticipate that fabricated psyllium-based nanofiber can be used as a promising candidate for wound healing and other biomedical applications.