Comparative analysis of formaldehyde and toluene sorption on indoor floorings and consequence on Indoor Air Quality

Indoor surfaces may be adsorptive sinks with the potential to change Indoor Air Quality. To estimate this effect, the sorption parameters of formaldehyde and toluene were assessed on five floorings by an experimental method using solid-phase microextraction in an airtight emission cell. Adsorption rate constants ranged from 0.003 to 0.075 m·h⁻¹, desorption rate constants from 0.019 to 0.51 h⁻¹, and the partition coefficient from 0.005 to 3.9 m, and these parameters vary greatly from one volatile organic compound/material couple to another indicating contrasted sorption behaviors. A rubber was identified as a sink of formaldehyde characterized by a very low desorption constant close to 0. For these sorbent floorings identified, the adsorption rates of formaldehyde are from 2 to 4 times higher than those of toluene. Two models were used to evaluate the sink effects of floorings on indoor pollutant concentrations in one room from different realistic conditions. The scenarios tested came to the conclusion that the formaldehyde sorption on one rubber (identified as a sink) has a maximum contribution from 15% to 21% for the conditions of low air exchange rate. For other floorings, the sorption has a minor contribution less than or equal to 5%, regardless of the air exchange rate.     

Barium titanate‐based nanodielectrics of two chemically recyclable thermosets

In this work was investigated the effect of the addition of barium titanate (BaTiO₃) on electrical properties of two chemically recyclable thermosets, polyhemiaminal (PHA) and polyhexahydro‐s‐triazine (PHT), both fabricated from 4,4′‐oxydianiline (ODA), an ether derivative of aniline and paraformaldehyde. Thermal and mechanical properties as well as chemical recyclability of the two polymers and their nanocomposites/nanodielectrics were also investigated. In addition, a quantitative analysis was conducted of the nanoparticle dispersion in the PHA‐/PHT‐based BaTiO₃‐containing nanocomposites using transmission electron microscopy imaging and the nearest‐neighbor distance index and this index was used to analyze the investigated properties in connection with the proper mechanisms. Regarding the electrical properties for both neat polymers, conductivity values of the order of 10^?8 S m^?1 at 100 Hz were observed and dielectric constant values close to 2.80 for both polymers at 1 kHz. The addition of 0.5 wt% of BaTiO₃ ferroelectric nanoparticles increased by about 44% the dielectric constant (1 kHz) and conductivity (10² Hz) of the PHA‐based nanocomposite. PHA and PHT exhibited glass transition temperature (T_g) values in the range 125–180 °C. An increase of 7 °C in T_g was observed after the incorporation of 0.5 wt% of BaTiO₃ into PHA. Concerning the mechanical properties, values in the range 4.00–4.45 GPa for reduced modulus and 0.30–0.43 GPa for nanohardness for PHA and PHT polymers were observed. Independently of filler content or polymer matrix, both mechanical properties were enhanced after the addition of BaTiO₃. The chemical recycling of PHA/PHT and all nanocomposites in the initial ODA reagent after sulfuric acid treatment was successfully characterized using the NMR and Fourier transform infrared spectroscopic techniques. © 2018 Society of Chemical Industry     

Synthesis of Long-Chain β-Lactones and Their Antibacterial Activities against Pathogenic Mycobacteria

In the quest for new antibacterial agents, a series of novel long- and medium-chain mono- and disubstituted β-lactones was developed. Their activity against three pathogenic mycobacteria—M. abscessus, M. marinum, and M. tuberculosis—was assessed by the resazurin microtiter assay (REMA). Among the 16 β-lactones synthesized, only 3-hexadecyloxetan-2-one (VM005) exhibited promising activity against M. abscessus, whereas most of the β-lactones showed interesting activities against M. marinum, similar to that of the classical antibiotic, isoniazid. Regarding M. tuberculosis, six compounds were found to be active against this mycobacterium, with β-lactone VM008 [trans-(Z)-3-(hexadec-7-en-1-yl)-4-propyloxetan-2-one] being the best growth inhibitor. The promising antibacterial activities of the best compounds in this series suggest that these molecules may serve as leads for the development of much more efficient antimycobacterial agents.     

Impact of the anode operating conditions on the liquid water distribution in the cathode gas diffusion layer

Previous experimental results indicate that the humidification conditions at the anode have an impact on the liquid water distribution in the cathode gas diffusion layer. Numerical simulations are developed to reproduce and analyze this effect. Results consistent with the experimental results are first obtained by playing with the partition coefficients of an advanced pore network model computing the liquid water formation and transfer in the cathode gas diffusion layer (GDL) for a large range of operating conditions. Then, a model for the full anode – cathode assembly is developed by combining the pore network model of the cathode GDL and a 1D model describing the heat and water transfer in the various components of the anode-cathode assembly. This enables one to generalize the dry – wet regime diagram introduced in a previous work by incorporating the effect of the humidity condition at the anode.     

Spatio-temporal evolution of the deformation around the Rio-Patras fault (Greece) observed by synthetic aperture radar interferometry from 1993 to 2017

We analysed the ground deformation across two blocks defined by the Rio-Patras fault from 1993 to 2017 using multi-temporal Synthetic Aperture Radar Interferometry (InSAR) techniques. Our main objective was to contribute to the assessment of seismic hazard near the large city of Patras. Multiple data-sets were used, each one covering different temporal periods. Descending and ascending acquisitions, providing different viewing geometries contribute to fully determine the ground displacement in 3D. The data-sets used are from the European Space Agency’s (ESA) European Remote Sensing (ERS), Environmental Satellite (ENVISAT) and SENTINEL-1 as well as German Aerospace Center (DLR) ’s TERRASAR-X missions. Considering ESA’s missions covering both acquisition geometries and long periods, the southern block, showing lack of a sufficient number of scatterers does not allow the displacement characterization. In contrary, the northern block is characterized by a high number of scatterers having values of maximum likehood ranging from ?3.5 to ?4.3 mm year^?1 for ascending geometry and from ?1.6 to ?2.7 mm year^?1 for the descending one. The fact that both geometries show negative values of displacements are consistent with downlift movement and at the same time the quantitative differentiation probably indicates an horizontal component as well.     

Software assurance practices for mobile applications

Mobile software applications have to cope with a particular environment that involves small size, limited resources, high autonomy requirements, competitive business models and many other challenges. To provide development guidelines that respond to these needs, several practices have been introduced; however, it is not clear how these guidelines may contribute to solve the issues present in the mobile domain. Furthermore, the rapid evolution of the mobile ecosystem challenges many of the premises upon which the proposed practices were designed. In this paper, we present a survey of the literature on software assurance practices for mobile applications, with the objective of describing them and assessing their contribution and success. We identified, organized and reviewed a body of research that spans in three levels: software development processes, software product assurance practices, and software implementation practices. By carrying out this literature survey, we reviewed the different approaches that researchers on Software Engineering have provided to address the needs that raise in the mobile software development arena. Moreover, we review the evolution of these practices, identifying how the constant changes and modernization of the mobile execution environment has impacted the methods proposed in the literature. Finally, we introduced discussion on the application of these practices in a real productive setting, opening an area for further research that may determine if practitioners have followed the proposed assurance paradigms.     

Intrinsic CFRP-metal-hybrids with rubber interface for the improvement of the damping behaviour

This paper presents an integrated passive damping approach in hybrid metal-CFRP parts for structural applications. In this concept a viscoelastic material is embedded in the joint zone of the hybrid component. To examine the connection strength single-lap-joint specimens were produced and tested and the influence of the used material combinations, different surface structures, and different process parameters i.e. the moment of cross-linking were evaluated. Afterwards, the metal-CFRP hybrids were tested in quasi-static tests to assess their connection strength and failure behaviour. Dynamic cyclic tensile tests with step-wise increased loading conditions were performed to determine the specimens damping behaviour and to estimate their fatigue performance. Finally, these results are compared to a state of the art metal-CFRP hybrid with rivets connecting both materials.     

On stochastic comparisons of finite mixtures for some semiparametric families of distributions

In this paper, we consider the classical finite mixture model, which is an effective tool for modeling lifetime distributions for random samples from heterogeneous populations. We discuss new results on stochastic comparison for two finite mixtures when each of them is drawn from one of the following semiparametric families, i.e., proportional hazards, accelerated lifetime and proportional reversed hazards.