Barium titanate‐based nanodielectrics of two chemically recyclable thermosets

In this work was investigated the effect of the addition of barium titanate (BaTiO₃) on electrical properties of two chemically recyclable thermosets, polyhemiaminal (PHA) and polyhexahydro‐s‐triazine (PHT), both fabricated from 4,4′‐oxydianiline (ODA), an ether derivative of aniline and paraformaldehyde. Thermal and mechanical properties as well as chemical recyclability of the two polymers and their nanocomposites/nanodielectrics were also investigated. In addition, a quantitative analysis was conducted of the nanoparticle dispersion in the PHA‐/PHT‐based BaTiO₃‐containing nanocomposites using transmission electron microscopy imaging and the nearest‐neighbor distance index and this index was used to analyze the investigated properties in connection with the proper mechanisms. Regarding the electrical properties for both neat polymers, conductivity values of the order of 10^?8 S m^?1 at 100 Hz were observed and dielectric constant values close to 2.80 for both polymers at 1 kHz. The addition of 0.5 wt% of BaTiO₃ ferroelectric nanoparticles increased by about 44% the dielectric constant (1 kHz) and conductivity (10² Hz) of the PHA‐based nanocomposite. PHA and PHT exhibited glass transition temperature (T_g) values in the range 125–180 °C. An increase of 7 °C in T_g was observed after the incorporation of 0.5 wt% of BaTiO₃ into PHA. Concerning the mechanical properties, values in the range 4.00–4.45 GPa for reduced modulus and 0.30–0.43 GPa for nanohardness for PHA and PHT polymers were observed. Independently of filler content or polymer matrix, both mechanical properties were enhanced after the addition of BaTiO₃. The chemical recycling of PHA/PHT and all nanocomposites in the initial ODA reagent after sulfuric acid treatment was successfully characterized using the NMR and Fourier transform infrared spectroscopic techniques. © 2018 Society of Chemical Industry     

Bamboo biochar-catalytic degradation of lignin under microwave heating

Abstract

Lignin biochar-catalytic depolymerization using biochar Fe-600, Fe-800, Ni-600, Ni-800 catalysts under microwave-heating (180?°C for 30?min) was explored in an ethanol/formic acid (1:1) media. Non-catalyst depolymerization was also studied and compared with the biochar-catalysts results. Characteristics of the bio-char catalysts were analyze by BET, XRD, and FT-IR. GPC, FT-IR, and MALDI-TOF MS spectrometry were also used to characterize the depolymerization products. The experimental results showed that the S_BET, V_t, and V_mec and average pore diameter of the biochars are considerably dependent on the preparation temperature and type of cation (Ni²⁺ or Fe³⁺). The maximum yield of bio-oil product was obtained as 85?wt% with the addition of biochar Ni-600 and the total amount of oligomers or monomers with a molecular weight of 164 to 446 reaches 80.4%.     

Inferring kinetic dissolution of NaCl in aqueous glycol solution using a low-cost apparatus and population balance model

An experimental methodology for inferring brine dissolution rate in monoethylene glycol (MEG) solutions at different temperatures using a webcam combined with a mathematical model is presented. The measurement system is designed to track the RGB (red, green, and blue) colour variations during the dissolution process. A dynamic model augmented with the population balance equation is applied to describe the dissolution process. Moreover, the dissolution rate is consistently related to the temperature and MEG concentration through the driving force based on the Gibbs energy and chemical affinity. The applied low-cost measurement apparatus proved to be a useful resource for tracking the dissolution dynamics in a wide range of undersaturation.     

Influence of the second phase on the room-temperature tensile and creep deformation mechanisms of α-β titanium alloys: Part I. Tensile deformation

The effects of α and β phase interactions on the room-temperature tensile and creep deformation behavior of α + β titanium alloys with Widmanst?tten microstructures were studied using Ti-6.0 wt pct Mn and Ti-8.1 wt pct V as the model two-phase alloy systems. This article, Part I, deals with tensile deformation. It was found that when the α phase is present as thin (<10-μm) plates in the α + β alloys, significant twinning occurs. No significant twinning was observed in single-phase alloys with the same chemistry and similar grain size. Additionally, the β phase of Ti-8.1 V deforms by stress-induced hexagonal martensite (α′), while only twinning occurs in the single-phase β alloy with the same chemistry. Twinning in the α phase in association with stress-induced martensite (SIM) in the β phase was observed for the first time in a two-phase titanium alloy. This behavior is explained in terms of a number of factors including elastic interaction stresses between the α and β phases, coherency between the α phase and hexagonal martensite, and β phase stability.     

Measurements of small-scale fading and path loss for long range RF tags

RF modulated backscatter (RFMB), also known as modulated radar cross section or sigma modulation, is a RF transmission technique useful for short-range, low-data-rate applications, such as nonstop toll collection, electronic shelf tags, freight container identification and chassis identification in automobile manufacturing, that are constrained to have extremely low power requirements. The small-scale fading observed on the backscattered signal has deeper fades than the signal from a traditional one-way link of the same range in the same environment because the fading on the backscattered signal is the product of the fading on the off-board-generated carrier times the fading on the reflected signal. This paper considers the continuous wave (CW) type of RFMB, in which the interrogator transmitter and receiver antennas are different. This two-way link also doubles the path loss exponent of the one-way link. This paper presents the cumulative distribution functions for the measured small-scale fading and the measured path loss for short ranges in an indoor environment at 2.4 GHz over this type of link.     

1H T2‐NMR monitoring of crosslinked polyolefin aging

This work examines the correlation between the ¹H‐NMR T₂ relaxation constant and the mechanical properties of aged crosslinked polyolefin cable insulation. T₂ experiments on unswollen samples could not differentiate between unaged and highly aged materials; all exhibited ¹H T₂ constants of approximately 0.5 ms. To accentuate the effects of aging, samples were swollen in various solvents. Unaged samples had T₂ values of approximately 15 ms in good solvents. With thermal aging, T₂ values decreased as the ultimate tensile elongation decreased. However, the correlation between T₂ and elongation differed for samples irradiated with high‐energy radiation and for materials aged above versus below the crystalline melting temperature. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2578–2582, 2003