Ternary Blends of Renewable Fast Pyrolysis Bio-Oil,Advanced Bioethanol,and Marine Gasoil as Potential Marine Biofuel

An alternative for reducing emissions from marine fuel is to blend bio-oil from lignocellulose non-edible feedstocks to diesel fossil fuels. Phase diagrams of the ternary systems were built to represent the transition from heterogeneous regions to homogeneous regions. Four homogeneous blends of bio-oil of eucalyptus-bioethanol-marine gasoil were experimentally characterized with respect to the most important fuel parameters for marine engines: water content, flash point, low heating value, viscosity, and acidity. Blends with closer properties to marine gasoil replacement, lower costs, and environmental impacts should be tested for large engines.     

Molecular structure and granule morphology of native and heat‐moisture‐treated pinhão starch

Pinhão seed is an unconventional source of starch and the pines grow up in native forests of southern Latin America. In this study, pinhão starch was adjusted at 15, 20 and 25% moisture content and heated to 100, 110 and 120 °C for 1 h. A decrease in λ max (starch/iodine complex) was observed as a result of increase in temperature and moisture content of HMT. The ratio of crystalline to amorphous phase in pinhão starch was determined via Fourier transform infra red by taking 1045/1022 band ratio. A decrease in crystallinity occurred as a result of HMT. Polarised light microscopy indicated a loss of birefringence of starch granules under 120 °C at 25% moisture content. Granule size distribution was further confirmed via scanning electron microscopy which showed the HMT effects. These results increased the understanding on molecular and structural properties of HMT pinhão starch and broadened its food and nonfood industrial applications.     

Corrosion behaviour of decorative and wear resistant coatings on steel deposited by reactive magnetron sputtering - Tests and improvements

Depositions of decorative and wear resistant single layer coatings like TiN, Ti(B,N), CrN, NbN, NbON, (Ti,Mg)N and multilayer coatings like Cr/CrN, Nb/NbN, CrN/NbN and NbN/Nb-C:H were performed using reactive magnetron sputtering. The corrosion behaviour of the coated high speed steel substrates was studied in sodium chloride containing media by open-circuit-potential measurements, potentiodynamic corrosion tests and salt spray tests. Up to now, the best improvements with respect to the corrosion resistance in salt spray tests could be obtained for the system (Ti,Mg)N/high speed steel.     

A panoramic view and swot analysis of artificial intelligence for achieving the sustainable development goals by 2030: progress and prospects

Applied Intelligence - The17 Sustainable Development Goals (SDGs) established by the United Nations Agenda 2030 constitute a global blueprint agenda and instrument for peace and prosperity...     

Water flux,DSC, and cytotoxicity characterization of membranes of cellulose acetate produced from sugar cane bagasse,using PEG 600

Summary In this article, cellulose acetate produced through the homogeneous acetylation of sugar cane bagasse cellulose was used to produce membranes, using poly(ethyleneglycol) 600 (PEG 600) as an admixture. The membranes were characterized using water flux measurements (Payne’s cup), differential scanning calorimetry (DSC) and neutral red uptake (cytotoxicity). The results showed that PEG 600 acts as a crystallinity inductor and/or pore former in the cellulose acetate matrix. The induction of crystallinity is important for this system since it had not been reported on the literature yet. The results also demonstrated that the studied membranes present a nontoxic behavior.     

GraftFast Surface Engineering to Improve MOF Nanoparticles Furtiveness

Controlling the outer surface of nanometric metal–organic frameworks (nanoMOFs) and further understanding the in vivo effect of the coated material are crucial for the convenient biomedical applications of MOFs. However, in most studies, the surface modification protocol is often associated with significant toxicity and/or lack of selectivity. As an alternative, how the highly selective and general grafting GraftFast method leads, through a green and simple process, to the successful attachment of multifunctional biopolymers (polyethylene glycol (PEG) and hyaluronic acid) on the external surface of nanoMOFs is reported. In particular, effectively PEGylated iron trimesate MIL‐100(Fe) nanoparticles (NPs) exhibit suitable grafting stability and superior chemical and colloidal stability in different biofluids, while conserving full porosity and allowing the adsorption of bioactive molecules (cosmetic and antitumor agents). Furthermore, the nature of the MOF–PEG interaction is deeply investigated using high‐resolution soft X‐ray spectroscopy. Finally, a cell penetration study using the radio‐labeled antitumor agent gemcitabine monophosphate (³H‐GMP)‐loaded MIL‐100(Fe)@PEG NPs shows reduced macrophage phagocytosis, confirming a significant in vitro PEG furtiveness.     

Pull-in-based μg-resolution accelerometer: Characterization and noise analysis

The pull-in time (t_pi) of electrostatically actuated parallel-plate microstructures enables the realization of a high-sensitivity accelerometer that uses time measurement as the transduction mechanism. The key feature is the existence of a metastable region that dominates pull-in behavior, thus making pull-in time very sensitive to external accelerations. Parallel-plate MEMS structures have been designed and fabricated using a SOI micromachining process (SOIMUMPS) for the implementation of the accelerometer. This paper presents the experimental characterization of the microdevices, validating the concept and the analytical models used. The accelerometer has a measured sensitivity of 0.25 μs/μg and a bandwidth that is directly related to the pull-in time, BW = 1/2t_pi ≈ 50 Hz. These specifications place this sensor between the state of the art accelerometers found both in the literature and commercially. More importantly, the resolution of the measurement method used is very high, making the mechanical-thermal noise the only factor limiting the resolution. The in-depth noise analysis to the system supports these conclusions. The total measured noise floor of 400 μg (100 μs) is mainly due to the contribution of the environmental noise, due to lack of isolation of the experimental setup from the building vibrations (estimated mechanical thermal noise of 2.8 μg/√Hz). The low requirements of the electronic readout circuit makes this an interesting approach for high-resolution accelerometers.     

Sacha inchi (Plukenetia volubilis L.) shell: an alternative source of phenolic compounds and antioxidants

Sacha inchi seed (SI) is known as a rich source of oil with high content of polyunsaturared fatty acids of the ω‐3 and ω‐6 type (~85% of total fatty acids). However, few studies have focused on the use of by‐products from the seed. The aim of this study was to characterise the main phenolic families present in SI shell and to evaluate the best extraction solvent for the extraction of phenolic compounds (PC) and antioxidant capacity (AOXC). The PC content corresponded to 74.5 ± 5.1 mg g^?1 of which 93.1% were condensed tannins and the remaining compounds corresponded to free and bound phenolic acids, hydrolyzable tannins, flavonoids and flavanoids. Protocatechic and p‐coumaric acids but also hydroxycinammic acid derivatives of ferulic and o‐coumaric type and lignan derivatives were identified. Acetone containing solvents favoured the extraction of higher amounts of total PC and AOXC. This study highlights the potential use of SI shell as a novel and alternative source of PC antioxidants for the nutraceutical and/or functional food industries.