Recovery of fluorocarbons in Japan as a measure for abating global warming

The objective of this study is to evaluate the potential for recovering fluorocarbons as measures for the abatement of global warming. In this study, we focused on the three different kinds of fluorocarbons: CFCs, HCFCs and HFCs, and targeted refrigerant use because of the availability of relevant data. We first estimated future fluorocarbon emissions from the targeted appliances; we next compared those emissions in the units of CO₂ equivalent to the level of CO₂ emissions in 1990 from a quantitative point of view. As the result of this study, it was found that fluorocarbon emissions in 1999 and 2010 would be equal to approximately 7 and 3% of the level of CO₂ emissions in 1990 respectively. Moreover, if we implement a 100% recovery rate in every recovery route, we can reduce a large amount of emissions which correspond to approximately 2–5% of the level of CO₂ emissions in 1990, even if we take into account the energy-related CO₂ emissions by the transportation and decomposition of fluorocarbons.     

A Novel UWB Pulse Shape Modulation System

In this paper novel modified Hermite polynomial functions for use in impulse radio (ultra-wideband) communications are proposed. With these functions pulse shapes which are orthogonal and have nearly constant pulse width regardless of the pulse order are generated. These properties hold under the effects of differentiation. An M-ary communication system is constructed using these pulse shapes. A Matlab model for generating the pulses is designed and the effect of timing jitter on the performance of the system is investigated by computer simulation.     

Analysis of shielded microstrip lines with arbitrary metallizationcross section using a vector finite element method

The finite element method (FEM) with the high-order mixed-interpolation-type triangular element is used to solve the problem of practical microstrip lines with arbitrary metallization cross section. Analyses are carried out to produce the frequency characteristics of propagation constant, characteristic impedance, and attenuation constant of shielded microstrip lines with rectangular, trapezoidal, and semi-trapezoidal strip cross sections. A comparison of the numerical results with those of the existing results shows good agreement and thus verifies the versatility of the FEM. Also, the numerical results show the effects of the metallization cross sections on the transmission properties and thus emphasize the importance of considering the practical microstrip configurations in the design of miniaturized MMICs     

A high resolution negative working resist,LMR-UV,for g- and i-line lithography

LMR-UV (“low molecular weight resist for uv lithography”), a naphthoquinone-diazide sulfonic acid ester of a novolak resin, is a negative working resist. The mechanism of insolubilization of LMR-UV is based on the facts that the naphthoquinone-diazide moiety is decomposed to indenecarboxylic acid (polar compound) by photolysis upon UV irradiation and that the irradiated resist film insolubilizes in a non-polar developer. LMR-UV reliably forms 0.6 μm lines and spaces over a reflective substrate with steps by using a g-line stepper having a 0.35 NA lens. 0.6 μm-wide aluminum patterns over topography are obtained by use of g-line exposure and reactive ion etching. By use of an i-line aligner (NA = 0.42), LMR-UV resolves 0.25 μm space patterns with overhang profiles. The profiles are due to the large absorption coefficient of 3.8 μm^?1. 0.3 μm wide aluminum patterns are formed by i-line exposure and lift-off metallization.     

Quantitative trait loci affecting 4-nitroquinoline 1-oxide-induced tongue carcinogenesis in the rat

The incidence of tongue carcinomas (TCs) induced by oral administration of 4-nitroquinoline 1-oxide in rats is strain dependent. The inbred Dark-Agouti (DA) strain showed a much higher susceptibility to large mass-forming infiltrative TCs than did the Wistar-Furth (WF) strain. Our previous study (M. Kitano et al, Jpn. J. Cancer Res., 87: 1097-1101, 1996) on crosses between these two strains postulated a dominant susceptibility gene in DA and a dominant resistance gene in WF rats. The present study mapped these loci by analyzing the backcrosses to each parent with simple sequence repeat polymorphisms. Five quantitative parameters were analyzed: (a) the number of TCs > 5 mm in diameter; (b) the total number of TCs per rat; (c) the diameter of the largest TCs (DTCmax values); (d) the number of non-TC cancers per rat; and (e) and the number of cancers of any site per rat. All of these parameters were closely correlated (P < 0.0001). DA rats had a semidominant gene (Stc1) favoring the development of 4-nitroquinoline 1-oxide-induced cancers on chromosome 19, closely linked to D19Mit9. Peak linkage was observed 4 cM distal from D19Mit9, with a logarithm of the odds (lod) score of 5.72 for the number of large TCs and 6.08 for the DTCmax. On the other hand, WF rats had a semidominant gene (Rtc1) mapped between D1Mit1 and D1Mit3, approximately 20 cM from D1Mit1, with a peak lod score of 3.30 for both the number of large TCs and the DTCmax. The main effect of Rtc1 seemed to be to reduce the size of the TCs. The action of these genes was dose dependent and cooperative. The final incidence of TC in DA, WF, F1, and backcross rats seemed to be explained by combinations of genotype at these two loci. Possible candidate genes for Stc1 and Rtc1 are discussed.     

The effect of gas atmospheres on resistivity of indium tin oxide films at high temperature

The effects of heat treatment in Q₂, O₂ and N₂, and Ar gases on the high temperature (500 C) electrical resistivity of indium tin oxide (ITO) film 52 nm thick prepared by chemical spray pyrolysis method were studied. The partial oxygen pressure effect on the resistivity was found to be to . The resistivity changes for cyclic exchange of O₂ by Ar gas at 500 C. These lead to the conclusion that chemisorption of oxygen atoms in the film surface is dominant for this thin film, for thicker films such as 640 nm oxygen diffusion is found to occur. The Langmuir model of the monolayer isothermal adsorption of oxygen atoms in the surface is applicable to the rapid change of resistivity.     

Alteration of substrate specificity of cholesterol oxidase from Streptomyces sp. by site-directed mutagenesis

Despite the structural similarities between cholesterol oxidasefrom Streptomyces and that from Brevibacterium, both enzymesexhibit different characteristics, such as catalytic activity,optimum pH and temperature. In attempts to define the molecularbasis of differences in catalytic activity or stability, substitutionsat six amino acid residues were introduced into cholesteroloxidase using site-directed mutagenesis of its gene. The aminoacid substitutions chosen were based on structural comparisonsof cholesterol oxidases from Streptomyces and Brevibacterium.Seven mutant enzymes were constructed with the following aminoacid substitutions: L117P, L119A, L119F, V145Q, Q286R, P357Nand S379T. All the mutant enzymes exhibited activity with theexception of that with the L117P mutation. The resulting V145Qmutant enzyme has low activities for all substrates examinedand the S379T mutant enzyme showed markedly altered substratespecificity compared with the wild-type enzyme. To evaluatethe role of V145 and S379 residues in the reaction, mutantswith two additional substitutions in V145 and four in S379 wereconstructed. The mutant enzymes created by the replacement ofV145 by Asp and Glu had much lower catalytic efficiency forcholesterol and pregnenolone as substrates than the wild-typeenzyme. From previous studies and this study, the V145 residueseems to be important for the stability and substrate bindingof the cholesterol oxidase. In contrast, the catalytic efficiencies(k_cat/K_m) of the S379T mutant enzyme for cholesterol and pregnenolonewere 1.8- and 6.0-fold higher, respectively, than those of thewild-type enzyme. The enhanced catalytic efficiency of the S379Tmutant enzyme for pregnenolone was due to a slightly high k_catvalue and a low K_m value. These findings will provide severalideas for the design of more powerful enzymes that can be appliedto clinical determination of serum cholesterol levels and assterol probes.     

Preparation of Aluminum Nitride–Silicon Carbide Nanocomposite Powder by the Nitridation of Aluminum Silicon Carbide

Aluminum nitride (AlN)–silicon carbide (SiC) nanocomposite powders were prepared by the nitridation of aluminum-silicon carbide (Al₄SiC₄) with the specific surface area of 15.5 m²·g⁻¹. The powders nitrided at and above 1400°C for 3 h contained the 2H-phases which consisted of AlN-rich and SiC-rich phases. The formation of homogeneous solid solution proceeded with increasing nitridation temperature from 1400° up to 1500°C. The specific surface area of the AlN–SiC powder nitrided at 1500°C for 3 h was 19.5 m²·g⁻¹, whereas the primary particle size (assuming spherical particles) was estimated to be ∼100 nm.     

Measurement of self-diffusion coefficients in Li ionic conductors by using the short-lived radiotracer of 8Li

For the effective use of short-lived radioactive beams, soon to be available at the Tokai Radioactive Ion Accelerator Complex, the authors have developed a radiotracer method for diffusion studies in solids. The experimental test was performed by the measurement of the diffusion coefficients of Li in a sample of the compound βLiAl using an α-emitting radiotracer of ⁸Li (T_1/2=0.84 s). It was found that the time-dependent yields of the α particles from the diffusing ⁸Li that was initially implanted in the sample could be used as a measure of the diffusivity of the tracer in a nondestructive way. The method was applied to measure the self-diffusion coefficients of Li in βLiGa, and for investigating how the Li diffusion in the Li ionic conductors is affected by the concentration of atomic defects (i.e., the existence of the atomic vacancies of Li and the defects in Ga sites that are replaced by Li).