Benchmark experiment of large-angle scattering reaction cross section of iron at 14 MeV using two shadow bars – Comparison of experimental results with ENDF/B-VIII –

ABSTRACT

It is important to perform neutron transport simulations with accurate nuclear data in the neutronics design of a fusion reactor. However, absolute values of large-angle scattering cross sections vary among nuclear data libraries even for well-examined nuclide of iron. Benchmark experiments focusing on large-angle scattering cross sections were thus performed to confirm the correctness of nuclear data libraries. The series benchmark experiments were performed at a DT neutron source facility, OKTAVIAN of Osaka University, Japan, by the unique experimental system established by the authors’ group, which can extract only the contribution of large-angle scattering reactions. This system consists of two shadow bars, target plate (iron), and neutron detector (niobium). Two types of shadow bars were used and four irradiations were conducted for one experiment, so that contribution of room-return neutrons was effectively removed and only large-angle scattering neutrons were extracted from the measured four Nb reaction rates. The obtained experimental results were compared with calculations for five nuclear data libraries including JENDL-4.0, JEFF.-3.3, FENDL-3.1, ENDF/B- VII, and recently released ENDF/B-VIII. It was found from the comparison that ENDF/B-VIII showed the best result, though ENDF/B-VII showed overestimation and others are in large underestimation at 14 MeV.     

Phase behavior in liquid crystallization for diblock copolymers consisting of rubbery amorphous and side-chain liquid crystalline components

Phase behavior in liquid crystallization was studied for a series of liquid crystalline (LC) diblock copolymers consisting of rubbery amorphous and side-chain liquid crystalline components, poly(n-butyl acrylate) (PBA) and poly[11-(4′-cyanophenyl-4″-phenoxy)undecyl acrylate] (PLC), respectively, using a time-resolved small-angle X-ray scattering (SAXS) techniques, DSC and polarized optical microscopy (POM). The block copolymers used had three kinds of copolymer compositions, 44, 20 and 15 wt% of PLC compositions (BLC44, BLC20 and BLC15, respectively). BLC44 showed a smectic liquid crystalline structure. In the process of liquid crystallization for BLC44, the SAXS peak due to the microphase separation structure existing before liquid crystallization was changed continuously to be at a smaller angular side, and at almost the same time, a new peak appeared at a further smaller angular side and developed. The former peak disappeared with the development of liquid crystallization. The behavior of these SAXS peaks suggests that the microphase separation structure was changed discretely at the transition from isotropic to smectic and that two phases coexist in the early stage of the liquid crystallization. The coexistence of two peaks in the early stage of the liquid crystallization corresponded to the POM observation. In the isotropization process, coexistence of two phases was not observed. For BLC20 exhibiting a cylindrical structure in both isotropic and liquid crystalline states, the liquid crystalline structure was not smectic but probably nematic, and the spacing was changed continuously in liquid crystallization. No liquid crystallization was observed in SAXS, POM and DSC for BLC15. The orientation of smectic layers within lamellar domains was investigated using 2D-SAXS images. The smectic layer was aligned perpendicularly to the lamellar interface.     

A 7 ns 1 Mb BiCMOS ECL SRAM with shift redundancy

A 7-Mb BiCMOS ECL (emitter coupled logic) SRAM was fabricated in a 0.8 μm BiCMOS process. An improved buffer with a high-level output of nearly V_CC is adopted to eliminate the DC current in the level converter circuit, and the PMOS transistor has a wide operating margin in the level converter. The configurable bit organization is realized by using a sense-amplifier switch circuit with no access degradation. A wired-OR demultiplexer for the ×1 output, having the same critical path as the ×4 output circuit, allows for the same access time between the two modes. The ×1 or ×4 mode is electrically selected by the external signal. A simplified programming redundancy technology, shift redundancy, is utilized. Address programming is performed by cutting only one fuse in the shift redundancy. The RAM operates at the ECL-10K level with an access time of 7 ns. and the power dissipation at 50 MHz is 600 mW for the × mode     

Formation of phase structure and crystallization behavior in blends containing polystyrene–polyethylene block copolymers

The microphase separation structure in the molten state and the structure formation in crystallization from such ordered melt were investigated for the blends of polystyrene–polyethylene block copolymers (SE) with polystyrene homopolymer (PS) and polyethylene homopolymer (PE) and for the blends consisting of two kinds of SE with different copolymer compositions from each other, using synchrotron small-angle X-ray scattering techniques (SAXS). The copolymer compositions of SE block copolymers employed were 0.34, 0.58 and 0.73 wt. fraction of PE, and their melt morphologies were cylindrical, lamellar and lamellar, respectively. Macrophase separation or the morphology change in the melt occurred depending on the molecular weight and the blend composition, as reported so far. In crystallization from such macrophase-separated and microphase-separated melts, the melt morphology was completely kept for all the blends. Crystallization behavior was also investigated for the blends. The crystallization within the spherical and cylindrical domains surrounded by glassy PS was not observed for SE/PS blends. In the crystallization from the macrophase-separated melt, two exothermal peaks were observed in the DSC measurements, while a single peak was observed for other blends. For the blends with PS, the degree of crystallinity was depressed and the apparent activation energy of crystallization was high, compared to those for the corresponding neat SE. For SE/PE and SE/SE blends, those were changed depending on the blend composition.     

Forming of aluminium alloy at temperatures just below melting point

In order to improve the mechanical properties of products, a forming process of a solid material at a temperature just below the melting point is proposed. The material is deformed at the semi-solid temperature due to the heat generation caused by plastic deformation. The tensile strength, elongation, hardness and toughness of the aluminium alloy (Al–7%Si–0.3%Mg) billet extruded at temperatures between 500 and 550 °C are compared with those of the billet extruded in the hot forming (450 °C) and the semi-solid (560 °C) temperatures. The billet temperature during forming is evaluated by the finite element simulation. The tensile strength and hardness of the billet extruded at 550 °C just below the solidus temperature are higher than those for a billet at 450 °C, and they are almost the same as those for a billet deformed at 560 °C in the semi-solid region. The elongation and toughness of the extruded billet at 550 °C are lower than those for a billet at 450 °C. The forming load at 550 °C is almost half of that at 450 °C. Cracking on the surface of the extruded billet occurs at a high punch speed. The calculated temperature when the solid billet is extruded in the semi-solid state agrees well with the experimental one at which the tensile and hardness are improved.     

What kind of floor am I standing on? Floor surface identification by a small humanoid robot through full-body motions

This study addresses a floor identification method for small humanoid robots that work in such daily environments as homes. The fundamental difficulty lays in a method to understand the physical properties of floors. To achieve floor identification with small humanoid robots, we used inertial sensors that can be easily installed on such robots, and dynamically selected a full-body motion that physically senses floors to achieve accurate floor identification. We collected a training data-set over 10 different kinds of common floors in home environments. We achieved 85.7% precision with our proposed method. We also demonstrate that our robot could appropriately change its locomotion behaviours depending on the floor identification results.     

Interaction between zinc dialkyldithiophosphate and amine

This paper reports work on complex formation from ZDP and various aliphatic amines, and their equilibrium states in oil, adsorptivities and antiwear properties are investigated. Complex formation from ZDP and amine was proven by isolation and identification of solid crystals, and various complexes were found from mono- and diamines. The complex from monoamine has lower adsorptivity than free ZDP, while the poorer adsorptivity of ZDP/monoamine complex makes its antiwear property worse.     

Fabrication of aluminium foams from powder by hot extrusion and foaming

In order to produce aluminium foams for light-weight and energy absorbing structures of automobiles, a method for fabricating aluminium foam from powder mixed with a foaming agent by using a mould is proposed. The method consists of four sequential processes: powder compacting, extruding, foaming and moulding. In the experiment for fabricating aluminium foam from powder, the conditions of powder extrusion and foaming by the heated die are determined from the density of the aluminium foams made without a mould. The experimental results show that the relative density of the aluminium foam made under appropriate conditions is 0.22. In moulding of aluminium foam, a stainless steel pipe is used as a mould and the cylindrical aluminium foam is produced by filling into the pipe mould. The distribution of relative density within the aluminium foam bar is in a range of 0.2–0.3 by rapid cooling of the pipe. To examine the ratio of deformation energy to weight of the pipe including the aluminium foam, a compression test using a press is carried out. The deformation energy of the pipe can be increased with aluminium foam filled by the proposed method.     

Toxicity and tetramine contents of salivary glands from carnivorous gastropods

Salivary glands from 29 species of marine carnivorous gastropods in nine families were examined for lethal activity against mice and tetramine content. Mouse lethality was assayed by intravenous injection of buffer extracts into mice, and was detected in 14 species. Heat-stability tests confirmed that toxins in four species were thermolabile, while those in eight species were thermostable. Based on the tetramine contents determined by the colorimetric method using methanolic extracts, the thermostable toxins in seven species (Neptunea eulimatalamellosa, N. vinosa, N. arthritica, N. bulbacea, N. intersculpta f. pribiloffensis, N. intersculpta f. frater pilsbry and Hemifusus tuba) were considered to be tetramine contained at high levels (more than 900 micrograms/g salivary gland), but that in one species (Buccinum opisthoplectum) appeared to be a low-molecular-weight compound differing from tetramine. It is interesting that one (Hemifusus tuba) of the seven species containing high amounts of tetramine belongs to the family Melongenidae, although the other six Neptunea species are members of the family Buccinidae, as expected from previous studies.