Synthesis,characterization and charge transport properties of Pr–Ni Co-doped SrFe2O4 spinel for high frequency devices applications

Ferrites are materials of interest due to their broad applications in high technological devices and a lot of research has been focused to synthesize new ferrites. In this regard, an effort has been devoted to synthesize spinel Pr–Ni co-substituted strontium ferrites with a nominal formula of Sr_1-xPr_xFe_2-yNi_yO₄ (0.0 ≤ x ≤ 0.1, 0.0 ≤ y ≤ 1.0). The cubic structure of pure and Pr–Ni co-substituted strontium ferrite samples calcinated at 1073 K for 3 h has been confirmed through X-ray diffraction (XRD). Average sizes of crystallites (18–25 nm) have been estimated from XRD analysis and nanometer particle sizes of synthesized ferrites have been further verified by scanning electron microscopy (SEM). SEM results have also shown that particles are mostly agglomerated and all the samples possess porosity. It has been observed that at 298 K, the values of resistivity (ρ) increase, while that of AC conductivity, dielectric loss, and dielectric constants decrease with increasing amounts of Pr³⁺ and Ni²⁺ ions. The values of dielectric parameters initially decrease with frequency and later become constant and can be explained on the basis of dielectric polarization. Electrochemical impedance spectroscopy (EIS) studies show that the charge transport phenomenon in ferrite materials is mainly controlled via grain boundaries. Overall, synthesized ferrite materials own enhanced resistivity values in the range of 1.38 × 10⁹–1.94 × 10⁹ Ω cm and minimum dielectric losses, which makes them suitable candidates for high frequency devices applications.     

Processing of engineering ceramics with high power CO2 lasers

The hardness and brittleness of high performance engineering ceramics such as zirconia, aluminia, silicon carbide and silicon nitride makes traditional processing very expensive and time consuming. Efforts have been made to cut thick commercial ceramics with a continuous wave CO₂ laser. The results obtained so far are very promising and materials up to 10 mm in thickness have been cut successfully.     

A review on improving the autonomy of unmanned surface vehicles through intelligent collision avoidance manoeuvres

In recent years unmanned vehicles have grown in popularity, with an ever increasing number of applications in industry, the military and research within air, ground and marine domains. In particular, the challenges posed by unmanned marine vehicles in order to increase the level of autonomy include automatic obstacle avoidance and conformance with the Rules of the Road when navigating in the presence of other maritime traffic. The USV Master Plan which has been established for the US Navy outlines a list of objectives for improving autonomy in order to increase mission diversity and reduce the amount of supervisory intervention. This paper addresses the specific development needs based on notable research carried out to date, primarily with regard to navigation, guidance, control and motion planning. The integration of the International Regulations for Avoiding Collisions at Sea within the obstacle avoidance protocols seeks to prevent maritime accidents attributed to human error. The addition of these critical safety measures may be key to a future growth in demand for USVs, as they serve to pave the way for establishing legal policies for unmanned vessels.     

An Insight View on Synthetic Protocol,Surface Activity,and Biological Aspects of Novel Biocompatible Quaternary Ammonium Cationic Gemini Surfactants

In this study, we prepared a novel series of diester-functionalized cationic gemini surfactants (C_m-E2O2-C_m) containing ethylene oxide as a spacer with varying alkyl chain lengths and characterized by ¹H NMR, FT-IR, elemental analysis, and ESI-MS. The physicochemical properties of the geminis were explored by tensiometry, fluorescence, dye solubilization, and Krafft point. These geminis acquire superior surface activity than the conventional surfactants. Fluorescence spectroscopy analysis affirmed that the micropolarity and aggregation number of micelles diminished with increase in the alkyl chain length. These geminis represent a new group of amphiphiles of considerably high biodegradability, better cleavability, and low toxicity as assessed by BOD test, FT-IR analysis, and HC₅₀ analysis, respectively. They also showed significant level of antimicrobial activity toward some specified bacterial strains of Gram-positive and Gram-negative by using agar well diffusion method. Furthermore, the thermogravimetric analysis provided information regarding thermal stabilities of the newly synthesized gemini surfactants.     

Effects of cobalt and potassium doping on thermal stability and electrical properties of radiation grafted acrylic acid onto poly(tetrafluoroethylene ethylene) copolymer films

Grafted copolymer of poly(tetrafluoroethylene ethylene) (ET) with acrylic acid (AAc) was prepared by direct radiation method. The obtained films were modified by treating with small amounts of Co²⁺ and K⁺ ions (1.0 wt %). The effects of such treatment on the thermal stability and electrical conductivity of these films were studied. Cobalt treatment did not much affect the thermal degradation of the films. The results obtained revealed that k⁺ treatment enhanced the thermal degradation of ET‐g‐PAAc, which started 273 K lower than that observed in the case of the untreated and Co²⁺‐treated films. Potassium and cobalt treatment of the investigated films increased their electrical conductivity (σ) and decreased the activation energy ΔE_σ. The increase in σ values was, however, more pronounced in the case of K⁺‐treated film. These results were discussed in terms of the effective increase in the hydrophilicity of the films, especially those treated with potassium. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 867–871, 2005     

γ‐Irradiation effects on the thermal and structural characteristics of modified,grafted polypropylene

The effects of both the degree of grafting and γ irradiation on the thermal stability and structural characteristic of polypropylene‐graft‐polyvinylpyrrolidone and polypropylene‐graft‐polyvinylpyrrolidone modified with α‐cyano‐δ‐(2‐thienyl) crotononitrile were investigated. The employed techniques were thermogravimetric analysis, differential thermogravimetry, and X‐ray diffraction. The thermal stability of various polymeric substrates was investigated through the determination of the degradation temperature and activation energy of degradation. The effects of different parameters on the structural characteristics of different films were investigated through the determination of possible changes in the degree of ordering of the polymeric substrates. The results revealed that the thermal stability of the trunk polymer, grafted polymer, and polymer modified by α‐cyano‐δ‐(2‐thienyl) crotononitrile increased progressively with an increasing degree of grafting. The increase was, however, more pronounced for the sample undergoing the lowest degree of grafting. The activation energy of the thermal degradation process remained almost unchanged, and this indicated that the degradation processes of the different films followed almost the same mechanism. The γ irradiation at a dose of 60 kGy of the sulfur‐treated polymeric films [i.e., the polymeric films treated with α‐cyano‐δ‐(2‐thienyl) crotononitrile] reduced their thermal stability. This conclusion was reached by the consideration of the changes observed in the pre‐exponential factor of the Arrhenius equation due to different chemical and γ‐irradiation treatments. The degree of ordering, evidenced by X‐ray diffraction measurements of the trunk polymer, grafted polymer, and modified polymer, suffered a significant drop. This drop was much more pronounced for the sulfur‐containing polymeric materials. The observed drop in the degree of ordering of the polymeric substrates was taken as a measure of the structure collapse due to a certain treatment (degree of grafting and sulfur inclusion). The γ irradiation of the sulfur‐containing polymeric materials greatly increased their degree of ordering, which reached a value greater than that measured for the trunk polymer. Therefore, it was concluded that the thermal stability increased as the degree of ordering decreased. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 506–515, 2006     

3D Simulation Research on Urea-SCR DeNO<em>x Catalyst for Diesel Engine

In order to reduce oxides of nitrogen (NOx) emanated from a diesel eng ine, a comprehensive urea selective catalyst reduction (SCR) DeNOx catalys t was modeled in which numerical simulations were used as a complementary tool f or the experimental investigations to make the design decisions, and hence short en the development process. In this approach, relevant conversion reactions were studied in 1D model, and the parameters obtained in this way were transferred t o 3D simulations. According to the results ...     

Delay-dependent anti-windup synthesis for stability of constrained state delay systems using pole-constraints

This paper proposes the design of anti-windup compensator gain for stability of actuator input constrained state delay systems using constrained pole-position of the closed-loop. Based on Delay-Dependent Lyapunov-Krasovskii functionals and local sector conditions, a new LMI characterization is derived that ensures closed-loop asymptotic stability of constrained state delay systems while accounting upper bound fixed state delay and largest lower bound of the system’s pole-position in the formulation of anti-windup gain. Besides, at saturation, the method significantly nullifies the inherent slow dynamics present in the system. It is shown in the comparative numerical examples that the LMI formulation draws stability with improved time-domain performance.