Influence of the filler type on the rupture behavior of filled elastomers

This work is devoted to the rupture behavior of elastomers filled with carbon black (CB) or silica. Two elastomers have been studied: one which crystallizes under strain, natural rubber (NR), and another one which does not crystallize, styrene butadiene rubber (SBR). The study of the crack propagation of Single Edge Notched specimen (SENT) during stretching at different speeds focuses on the crack initiation and crack deviation phenomenon. This deviation is of main importance in the materials crack resistance as it leads to a large increase in the energy needed for rupture. The deviation in filled or unfilled NR is controlled by crystallization, which is a slow process. In unfilled SBR, deviation is controlled by polymer chain orientation, which is hindered by relaxation mechanisms. The introduction of fillers promotes strain amplification, and strain anisotropy in the crack tip region of the notched samples, and therefore crack deviation. In term of energy density at break of the SBR composites, the SBR filled with silica treated with a covering agent is the most efficient. Thus, a weak interface between the silica and SBR promotes better rupture properties. When comparing Silica and CB filled NR, the highest strain energy to rupture is also obtained with silica. This might be due to the weaker filler‐matrix interface for silica. Thus, these results evidence the kinetic aspect of the rupture, and of the mechanisms it involves: the polymer relaxation, the crystallization (for NR), and the filler‐matrix interaction and decohesion, all of them being strongly interrelated. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

A theoretical and experimental study of a small-scale steam jet refrigerator

The paper provides the results of a theoretical and experimental study of a steam jet refrigerator. A small-capacity steam jet refrigerator has been tested with boiler temperatures in the range 120–140°C. The experimental data were found to be within 85% of the theoretical values. The experiments showed that choking of the secondary flow in the mixing chamber of the ejector plays an important role in the system performance. Maximum COP was obtained when the ejector was operated at its critical flow condition. Off-design performance characteristics of the system are provided.     

Mixed percolating network and mechanical properties of polypropylene/talc composites

Injected polypropylene/talc composites were studied to evaluate the conditions leading to the formation of a mixed talc/polymer crystalline lamella percolating network and the influence of such a network on the nanocomposite mechanical properties. The talc was either conventional micrometer‐sized (conventional talc) or submicrometer‐sized particles (μ‐talc). In the case of μ‐talc, several talc fractions were studied, ranging from 3 to 30 wt %. The nanocomposite crystallinity was characterized with differential scanning calorimetry and wide‐angle X‐ray scattering. Talc was found to act as a nucleating agent, and only the α phase was detected. Through quantification on a Wilchinsky diagram, the talc particles were found to lie in the sample plane, the polypropylene crystalline lamellae being orthotropically distributed perpendicularly to the talc particles. The mechanical properties of the composites were tested in different directions by tensile and compression tests. The mechanical behavior of the composites confirmed the microstructural model. For low talc loadings, the composite moduli could not be well fitted by a law of mixtures. The large difference between the observed and predicted moduli was attributed to the formation of a mixed percolating network, including talc particles and polypropylene crystalline lamellae. At high talc loadings, when the mixed percolating network was completely formed, the reinforcement could well be described by parallel coupling, which indicated a classical reinforcement mechanism. Finally, the value of the critical talc fraction, at which the mixed percolating network was formed, was examined as a function of talc. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Hydrolytic degradation of poly(l‐lactic acid)/poly(methyl methacrylate) blends

The hydrolytic degradation of poly(l ‐lactic acid)/poly(methyl methacrylate) (PLLA/PMMA) blends was carried out by the immersion of thin films in buffer solutions (pH = 7.24) in a shaking water bath at 60 °C for 38 days. The PLA/PMMA blends (0/100; 30/70; 50/50; 70/30; 100/0) were obtained by melt blending using a Brabender internal mixer and shaped into thin films of about 150 µm in thickness. Considering that PMMA does not undergo hydrolytic degradation, that of PLLA was followed via evolution of PLA molecular weight (recorded by size exclusion chromatography), thermal parameters (differential scanning calorimetry (DSC)) and morphology of the films (scanning transmission electron microscopy). The results reveal a completely different degradation pathway of the blends depending on the polymethacrylate/polyester weight ratio. DSC data suggest that, during hydrolysis at higher PMMA content, the polyester amorphous chains, more sensitive to water, are degraded before being able to crystallize, while at higher PLLA content, the crystallization is favoured leading to a sample more resistant to hydrolysis. In other words, and quite unexpectedly, increasing the content of water‐sensitive PLLA in the PLLA/PMMA blends does not mean de facto faster hydrolytic degradation of the resulting materials. © 2018 Society of Chemical Industry     

Evaluation of a novel combined ejector-absorption refrigeration cycle — I: computer simulation

This paper describes a novel refrigeration cycle based on the combination of an absorption cycle with an ejector refrigeration cycle. The combination brings together the advantages of absorption and ejector refrigeration systems and provides high COP for refrigeration and air-conditioning. The combined cycle is particularly suitable for utilising waste thermal energy. A computer simulation program was developed for the combined cycle and used to determine the performance of the system using LiBrH₂O for various generator, condenser and evaporator temperatures. Optimum operating conditions and ejector design data are also provided.     

A small capacity steam-ejector refrigerator: experimental investigation of a system using ejector with movable primary nozzle

This paper describes an experimental study of a steam-ejector refrigerator using an ejector with a primary nozzle that could be moved axially within the mixing chamber section. The effects on coefficient of performance and cooling capacity produced by adjusting the position of the nozzle were studied. The experimental rig and method are described and results are presented which clearly show the benefit of using such a primary nozzle.     

Experimental investigation of an ejector refrigerator: Effect of mixing chamber geometry on system performance

This paper describes an experimental study of an ejector refrigeration cycle using R11 as the working fluid. The system was tested with boiler temperature from 100 to 110°C, the condenser temperature from 35 to 41°C, and the evaporator temperature up to 12°C. Two different mixing chambers with throat diameter of 8 mm were used. Choking of the fluid was always found in the first mixing chamber, but not in the second one. The system was more flexible to operate when there was no choking in the mixing chamber. A cooling temperature as low as ?5°C could be obtained with COP between 0.1 and 0.25 and cooling capacity between 500 and 1700 W. Copyright © 2001 John Wiley & Sons, Ltd.     

Synthesis and characterization of microporous silica–alumina membranes

The development of microporous ceramic thin layers is of prime interest for sensors or gas separation membranes working at high temperature. Microporous silica membranes can be easily prepared by the sol–gel process. However the microporosity of pure silica is rapidly modified by steam at high temperature. One way to improve hydrothermal stability is to use mixed-oxide membranes. In this work, microporous silica–alumina membranes were prepared by a simple and robust sol–gel method. Tetraethoxysilane was mixed with an acidic alumina hydrosol. Urea was added for preparing the alumina hydrosol, for controlling the mixed-oxide network polycondensation and also as porogen agent. FTIR and ²⁷Al NMR spectroscopic analyses showed that for Si/Al molar ratios up to 6/1, homogeneous mixed oxides were obtained with a random distribution of Al and Si atoms in the oxide lattice based on tetrahedral units. The derived supported layers were crack-free as demonstrated by scanning electron microscopy (SEM) observations. Their microporosity was investigated using ellipsoporosimetry (EP) with films supported on flat dense substrates. He, N₂ and CO₂ permeance measurements were performed for membranes deposited on porous tubular substrates. The measured values of He/N₂ and He/CO₂ ideal selectivities are in agreement with the microporous nature of the prepared layers.     

Silica Glass from Aerosil by Sol-Gel Process: Densification and Textural Properties

Sol-gel processes allow the synthesis of inorganic materials from solutions of molecular precursors. These precursors can be either organic, inorganic, or a mixture of the two. The aim of this work is the preparation of aqueous solutions consisting of Aerosil OX 50 (fumed silica) using small amount of additives like ammonium fluoride NH₄F (less than 2%), which are dried at room temperature in order to obtain monolithic gels. These are then densified at temperatures below 1200°C and sintered at 1300°C in order to obtain pure silica glass. The textural properties evolution of these gels is investigated as a function of temperature by thermal analysis (mass loss, shrinkage, and density) and scanning electron microscopy.     

A review of absorption refrigeration technologies

This paper provides a literature review on absorption refrigeration technology. A number of research options such as various types of absorption refrigeration systems, research on working fluids, and improvement of absorption processes are discussed.