Atomistic simulations of grain boundary migration in copper

While the motion of twist boundaries can be readily studied by atomistic simulations with molecular dynamics (MD) under the action of an elastic driving force, the approach fails for tilt boundaries. This is due to the interaction of the elastic stress with the grain boundary (GB) structure, which causes plastic strain by GB sliding. A novel concept, the orientation correlated driving force, is introduced to circumvent this problem. It is shown that this concept can be successfully applied to the study of the migration of tilt boundaries. The migration behavior of several twist and tilt GBs was investigated. The transition from low-to high-angle boundaries can be captured, and a structural transition of tilt boundaries was found at high temperatures, which also affected the migration behavior. The results compare well with experimental results of the motion high-angle boundaries, but for low-angle boundaries, the agreement is poor. This article is based on a presentation made in the “Hillert Symposium on Thermodynamics & Kinetics of Migrating Interfaces in Steels and Other Complex Alloys,” December 2–3, 2004, organized by The Royal Institute of Technology in Stockholm, Sweden.     

Untersuchung der Verteilung und Intensität filamentierter Barrierenplasmen für die Behandlung von Oberflächen

The application of barrier discharges at atmospheric pressure in air expands on the market of plasma technology, because it is an ecological and cost‐effective alternative to other processes of surface treatment. These plasmas usually consist of a multitude of spatially and temporally localized filaments, whose distribution should be as even as possible for homogeneous treatment. This holds especially for the plasma treatment of sensitive goods such as wool or other textiles. In equipment for continuous pass of material the barrier arrangements often consist of a system cylinder – cylinder or cylinder – plane, whereby the gap width changes locally. Space distribution and intensity of filaments has been investigated by means of short‐time photography and spatially resolved measurement of current distribution and energy distribution derived from it. The local dependency found can be explained by means of a capacitive equivalent circuit.     

Desalination by distillation and by reverse osmosis — trends towards the future

As the requirement for fresh water increases worldwide, there is a need for more and more plants that are able to treat non-conventional water sources. Sea water has become an important source of fresh water in many arid regions. This feature provides an overview of recent process improvements in sea water desalination using reverse osmosis, multi-stage flash, multi-effect distillation and electrodialysis. Areas discussed include the use of alternative energy sources (wind energy, solar energy and nuclear energy) for reverse osmosis or distillation processes, and the impact of the different desalination process on the environment. Also covered are the implementation of hybrid processes in sea water desalination, and the pretreatment of desalination plants by pressure-driven membrane processes.     

The measurement of the diffusion coefficient and the sorption isotherm of water in paint films

An experimental technique together with a numerical model is proposed with which the diffusion coefficient and the sorption isotherm of water in paint can be measured. Inside a closed vessel, paint films are on stainless-steel plates. Water is present as water vapour in the air and in the paint. After blowing dry or wet air through the vessel for some time, the situation moves to a new equilibrium. The relative humidity of the air inside the vessel is measured as a function of time. From fitting the theoretical/numerical model against the experimental values, follow the diffusion coefficient and the sorption isotherm of water in the paint. The results show large scattering. When the independently measured sorption isotherm is used as an input parameter in the model, the fitting procedure gives much smaller scattering for the diffusion coefficient.     

Strengthening of concrete prisms using the plate-bonding technique

This paper presents the use of fracture mechanics for the plate bonding technique. Plates of steel or carbon-fibre reinforced plastic are bonded with an epoxy adhesive to rectangular concrete prisms and loaded in shear up to failure, what is normally known in fracture mechanics as mode II failure. In this special application a linear and a nonlinear approach are presented. The nonlinear equation derived for a realistic shear-deformation curve can only be used for numerical calculations. However, for simplified shear-deformation curves, the derived formula can be solved analytically. Results from tests, which are compared with the theory, are also presented.     

Electromigration-induced damage in bamboo Al interconnects

Depletion and hillock formation were examined in-situ in a scanning electron microscope (SEM) during electromigration of bamboo Al interconnect segments. Hillocks formed directly at the anode ends of the segments by epitaxial addition of Al at the bottom Al/TiN interface. Depletion occurred nonuniformly from the cathode end and stopped once the distance between the leading void and the hillock reached the critical length for electromigration at the given current density. A modified equation for the drift velocity is proposed, which includes the effect of nonuniform depletion and predicts that interconnects with nonuniform depletion are more reliable than those with uniform depletion.     

Insertional re-activation of a chloramphenicol acetyltransferase misfolding mutant protein

The deletion of nine residues from the C-terminus of the bacterialchloramphenicol acetyltransferase (CAT) results in depositionof the mutant protein in cytoplasmic inclusion bodies and lossof chloramphenicol resistance in Escherichia coli. This foldingdefect is relieved by C-terminal fusion of the polypeptide withas few as two residues. Based on these observations, efficientpositive selection for the cloning of DNA fragments has beendemonstrated. The cloning vector encodes a C-terminally truncatedCAT protein. Restriction sites in front of the stop codon allowthe insertion of target DNA, resulting in the production ofproperly folded CAT fusion proteins and regained chloramphenicolresistance. The positive selection of recombinants is accomplishedby growth of transformants on chloramphenicol-containing agarplates. The method appears particularly convenient for the cloningof DNA fragments amplified by the PCR because minimal informationto restore CAT folding can be included in the primers. The cloningof random sequences shows that the folding defect can be relievedby fusion to a wide variety of peptides, providing great flexibilityto the positive selection system. This vector may also contributeto the determination of the role of the C-terminus in CAT folding.     

Polymeric schiff's base chelates and their precursors 8a), some cobalt chelates as catalysts for the isomerization of quadrycyclane to norbornadiene

Summary Starting with Z-2, 3-diamino-2-butenedinitrile as diamine component the synthesis of the low molecular N,N,O,O-chelate 3.Co and its ligand 3 is optimized. An easy synthesis of the chelate 8.Co covalently bound on macroreticular resins is presented. The chelates 8.Co are the most active heterogenous catalysts for the valence isomerization of quadricyclane to norbornadiene today.